Tous les articles avec comité de lecture (ACL) du laboratoire :
AnnéeAuteurs et titre du documentLiens
2018Mehdi Salem, Sabine Le Roux, Gilles Dour, Pascal Lamesle, Karim Choquet, et al. Effect of aluminizing and oxidation on the thermal fatigue damage of hot work tool steels for high pressure die casting applications. International Journal of Fatigue, Elsevier, 2019, 119, p.126-138 [HAL] / [DOI]
2018Fenglin Liang, Martial Sauceau, Gilles Dusserre, Jean-Louis Dirion, Patricia Arlabosse. Modelling of the rheological behavior of mechanically dewatered sewage sludge in uniaxial cyclic compression. Water Research, IWA Publishing, 2018, 147, p.413-421 [HAL] / [DOI]
2018Sinh-Khoa Nguyen, Pierre-Louis Chiambaretto, Miguel Charlotte, Philippe Villedieu, Joseph Morlier, et al. Towards an analytical formulation for Fluid Structure tank vibration analysis: Modal equivalency using granular materials. Engineering Structures, Elsevier, 2018, 177, pp.345-356 [HAL] / [DOI]
2018N. Dubary, Christophe Bouvet, Samuel Rivallant, L. Ratsifandrihana. Damage tolerance of an impacted composite laminate. Composite Structures, Elsevier, 2018, 206, pp.261 - 271 [HAL] / [DOI]
2018Fadhel Chatti, Christophe Bouvet, Dominique Poquillon, Guilhem Michon. Numerical modelling of shear hysteresis of entangled cross-linked carbon fibres intended for core material. Computational Materials Science, Elsevier, 2018, 155, pp.350 - 363 [HAL] / [DOI]
2017Gian Luca Morini, Pamela Vocale, Marco Spiga, Stéphane Colin. Corrigendum to “Shear work contribution to convective heat transfer of dilute gases in slip flow regime”, [Eur. J Mech B Fluids 64 (2017) 60–68] European Journal of Mechanics - B/Fluids, Elsevier, 2018, 72, pp.467 - 470 [HAL] / [DOI]
2018Eric Paroissien, Lucas F.M. Da Silva, Frederic Lachaud. Simplified stress analysis of functionally graded single-lap joints subjected to combined thermal and mechanical loads. Composite Structures, Elsevier, 2018, 203, pp.85 - 100 [HAL] / [DOI]
2018Thierry Sentenac, Florian Bugarin, Benoit Ducarouge, Michel Devy. Automated thermal 3 D reconstruction based on a robot equipped with uncalibrated infrared stereovision cameras. Advanced Engineering Informatics, Elsevier, 2018, 38, pp.203 - 215 [HAL] / [DOI]
2018Simone Coniglio, Christian Gogu, Joseph Morlier. Weighted Average Continuity Approach and Moment Correction New strategies for non-consistent mesh projection in structural mechanics. Archives of Computational Methods in Engineering, Springer Verlag, 2018, [HAL] / [DOI]
2018Arnaud Wilhelm, Samuel Rivallant, Jean-François Ferrero, Joseph Morlier. Sandwich shield subjected to bird impact: Use of surrogate models for influencing parameter analysis and shield behaviour understanding. Journal of Sandwich Structures and Materials, SAGE Publications, 2018, [HAL] / [DOI]
2018Sinan Boztepe, Rémi Gilblas, Olivier De Almeida, Christian Gerlach, Yannick Le Maoult, et al. The role of microcrystalline structure on optical scattering characteristics of semi-crystalline thermoplastics and the accuracy of numerical input for IR-heating modeling. International Journal of Material Forming, Springer Verlag, 2018, 11 (5), pp.717-727 [HAL] / [DOI]
2018K. Moussaoui, Walter Rubio, Michel Mousseigne, T. Sultan, Farhad Rezai-Aria. Effects of Selective Laser Melting additive manufacturing parameters of Inconel 718 on porosity, microstructure and mechanical properties. Materials Science and Engineering: A, Elsevier, 2018, 735, pp.182 - 190 [HAL] / [DOI]
2018Marc Budinger, Valérie Pommier-Budinger, Lokman Bennani, Pierrick Rouset, Elmar Bonaccurso, et al. Electromechanical Resonant Ice Protection Systems: Analysis of Fracture Propagation Mechanisms. AIAA Journal, American Institute of Aeronautics and Astronautics, 2018, pp.1 - 11 [HAL] / [DOI]
2018Sabine Le Roux, Mehdi Salem, Anis Hor. Improvement of the bridge curvature method to assess residual stresses in selective laser melting. Additive Manufacturing, 2018, 22, p.320-329 [HAL] / [DOI]
2018Mahdi Masoumi Khalilabad, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher. Effect of tool geometry and welding speed on mechanical properties of dissimilar AA2198–AA2024 FSWed joint. Journal of Manufacturing Processes, Society of Manufacturing Engineers, 2018, 34 (Part A), pp.86 - 95 [HAL] / [DOI]
2018Dominique Fratantonio, Marcos Rojas-Cárdenas, Hacene Si Hadj Mohand, Christine Barrot, Lucien Baldas, et al. Molecular tagging velocimetry for confined rarefied gas flows: Phosphorescence emission measurements at low pressure. Experimental Thermal and Fluid Science, Elsevier, 2018, 99, pp.510-524 [HAL] / [DOI]
2018Mahmoud Harzallah, Thomas Pottier, Rémi Gilblas, Yann Landon, Michel Mousseigne, et al. A coupled in-situ measurement of temperature and kinematic fields in Ti-6Al-4V serrated chip formation at micro-scale. International Journal of Machine Tools and Manufacture, Elsevier, 2018, [HAL] / [DOI]
2018Fadhel Chatti, Dominique Poquillon, Christophe Bouvet, Guilhem Michon. Numerical modelling of entangled carbon fibre material under compression. Computational Materials Science, Elsevier, 2018, 151, pp.14 - 24 [HAL] / [DOI]
2018Joseph Morlier, Aniello Basile, Ankit Chiplunkar, M. Charlotte. An EGO-like Optimization Framework for Sensor Placement Optimization in Modal Analysis. Smart Materials and Structures, IOP Publishing, 2018, vol 27 (n° 7), pp 075004-075022 [HAL] / [DOI]
2018Juan de Dios Rodriguez-Ramirez, Bruno Castanié, Christophe Bouvet. Damage Mechanics Modelling of the shear nonlinear behavior of Nomex honeycomb core. Application to sandwich beams Mechanics of Advanced Materials and Structures, Taylor & Francis, 2018, pp.1 - 10 [HAL] / [DOI]
Smr Kazmi, Quentin Govignon, Simon Bickerton. Control of laminate quality for parts manufactured using the resin infusion process. Journal of Composite Materials, SAGE Publications, In press, [HAL] / [DOI]
Olivier De Almeida, Jean-François Ferrero, Laurent Escale, Gérard Bernhart. Charpy test investigation of the influence of fabric weave and fibre nature on impact properties of PEEK-reinforced composites. Journal of Thermoplastic Composite Materials, SAGE Publications (UK and US), In press, [HAL] / [DOI]
2018Robin Bouclier, Jean-Charles Passieux. A Nitsche-based non-intrusive coupling strategy for global/local isogeometric structural analysis. Computer Methods in Applied Mechanics and Engineering, Elsevier, 2018, [HAL] / [DOI]
2018Maxime Rollin, Luc Penazzi, Vincent Velay, Alain Dupuy, Sylvie Gallet. A new numerical strategy for SPF pressure profile computing based on statistical strain rate controlling. International Journal of Mechanical Sciences, Elsevier, 2018, 141, p.479-490 [HAL] / [DOI]
2018Yves Davila, Laurent Crouzeix, Bernard Douchin, Francis Collombet, Yves-Henri Grunevald. Identification and Modelling of the In-Plane Reinforcement Orientation Variations in a CFRP Laminate Produced by Manual Lay-Up. Applied Composite Materials, Springer Verlag (Germany), 2018, 25 (3), pp.647 - 660 [HAL] / [DOI]
2018Juan de Dios Rodriguez-Ramirez, Bruno Castanié, Christophe Bouvet. Experimental and numerical analysis of the shear nonlinear behaviour of Nomex honeycomb core: Application to insert sizing. Composite Structures, Elsevier, 2018, vol 193, pp 121-139 [HAL] / [DOI]
2018E Paroissien, Frederic Lachaud, Joseph Morlier, S. Schwartz. A Direct Method for the Assessment of Cohesive Zone Models for Thin Adhesive Layers Loaded in Mode I, Mode II, and Mixed-Mode I/II. Reviews of Adhesion and Adhesives, 2018, [HAL] / [DOI]
2018Ernane Silva, Cesar Deschamps, Marcos Rojas-Cárdenas, Christine Barrot-Lattes, Lucien Baldas, et al. A time-dependent method for the measurement of mass flow rate of gases in microchannels. International Journal of Heat and Mass Transfer, Elsevier, 2018, 120, pp.422 - 434 [HAL] / [DOI]
2018Soumaya Naanani, Jean-Philippe Monchoux, Catherine Mabru, Alain Couret. Pure climb of [001] dislocations in TiAl at 850 °C. Scripta Materialia, Elsevier, 2018, 149, pp.53-57 [HAL] / [DOI]
2018M Azib, Fulbert Baudoin, Nicolas Binaud, F Villeneuve-Faure, Florian Bugarin, et al. Numerical simulations for quantitative analysis of electrostatic interaction between atomic force microscopy probe and an embedded electrode within a thin dielectric: meshing optimization, sensitivity to potential distribution and impact of cantilever contribution. Journal of Physics D: Applied Physics, IOP Publishing, 2018, 51 (16), [HAL] / [DOI]
2018Stéphane Amiel, Etienne Copin, Thierry Sentenac, Philippe Lours, Yannick Le Maoult. On the thermal sensitivity and resolution of a YSZ:Er 3+ /YSZ:Eu 3+ fluorescent thermal history sensor. Sensors and Actuators A: Physical , Elsevier, 2018, 272, p.42-52 [HAL] / [DOI]
2018Pascal Florian, Olivier Dorival, Pablo Navarro, Steven Marguet, Jean-François Ferrero. Impact damage prediction in thin woven composite laminates-Part I: Modeling strategy and validation. Composite Structures, Elsevier, 2018, 190, pp.32 - 42 [HAL] / [DOI]
2018Florian Pascal, Ange Rogani, Bassam Mahmoud, Pablo Navarro, Steven Marguet, et al. Impact damage prediction in thin woven composite laminates – Part II: Application to normal and oblique impacts on sandwich structure. Composite Structures, Elsevier, 2018, 190, pp.43 - 51 [HAL] / [DOI]
2018Aurélien Mondière, Valentine Déneux, Nicolas Binot, Denis Delagnes. Controlling the MC and M2C carbide precipitation in Ferrium® M54® steel to achieve optimum ultimate tensile strength/fracture toughness balance. Materials Characterization, Elsevier, 2018, 140, p.103 - 112 [HAL] / [DOI]
2018Tao Li, Claude-Henri Lamarque, Sébastien Seguy, Alain Berlioz. Chaotic characteristic of a linear oscillator coupled with vibro-impact nonlinear energy sink. Nonlinear Dynamics, Springer Verlag, 2018, 91, pp.2319--2330 [HAL] / [DOI]
2018Oleksii Shtehin, Sébastien Seguy, Vincent Wagner, Yann Landon, Gilles Dessein, et al. Low-frequency chatter genesis during inclined surface copy-milling with ball-end mill: Experimental study. Machining Science and Technology, Taylor & Francis, 2018, 22 (4), pp.621 - 637 [HAL] / [DOI]
2018Patrice Longère. Respective/combined roles of thermal softening and dynamic recrystallization in adiabatic shear banding initiation. Mechanics of Materials, Elsevier, 2018, 117, pp.81 - 90 [HAL] / [DOI]
2018Mickaël Duval, Alexei Lozinski, Jean-Charles Passieux, Michel Salaün. Residual error based adaptive mesh refinement with the non-intrusive patch algorithm. Computer Methods in Applied Mechanics and Engineering, Elsevier, 2018, [HAL] / [DOI]
2018Jérôme Michetti, Adrian Basarab, Franck Diemer, Denis Kouamé. Comparison of an adaptive local thresholding method on CBCT and µ CT endodontic images. Physics in Medicine and Biology, IOP Publishing, 2018, 63 (1), [HAL] / [DOI]
2018D'Elia Raffaele, Gilles Dusserre, Sylvie Del Confetto, Nicolas Eberling-Fux, Cédric Descamps, et al. Effect of dicumyl peroxide concentration on the polymerization kinetics of a polysilazane system. Polymer Engineering and Science, Wiley-Blackwell, 2018, 58 (6), p.859-869 [HAL] / [DOI]
1425Bessam Zeramdini, Camille Robert, Guenaël Germain, Thomas Pottier. Numerical simulation of metal forming processes with 3D adaptive Remeshing strategy based on a posteriori error estimation. International Journal of Material Forming, Springer Verlag, In press, [HAL] / [DOI]
2018Thibaut Hirschler, Robin Bouclier, Arnaud Duval, Thomas Elguedj, Joseph Morlier. Isogeometric sizing and shape optimization of thin structures with a solid-shell approach. Structural and Multidisciplinary Optimization, Springer Verlag (Germany), 2018 [HAL]
2018Patrice Longère. Adiabatic shear banding assisted dynamic failure: Some modeling issues. Mechanics of Materials, Elsevier, 2018, 116, pp.49-66 [HAL] / [DOI]
2018Sylvian Dubreuil, Michel Salaün, Emmanuel Rodriguez, Frank Petitjean. Construction and identification of a D-Vine model applied to the probability distribution of modal parameters in structural dynamics. Mechanical Systems and Signal Processing, Elsevier, 2018, vol 98, pp 190-208 [HAL] / [DOI]
2018Matthias Barus, Hélène Welemane, Valérie Nassiet, Marie-Laetitia Pastor, Arthur Cantarel, et al. NDT-based design of joint material for the detection of bonding defects by infrared thermography. NDT and E International, Elsevier, 2018, 93, pp.157-163 [HAL] / [DOI]
2018J. Sweeney, P.E. Spencer, D. Vgenopoulos, M. Babenko, Florian Boutenel, et al. Application of activated barrier hopping theory to viscoplastic modeling of glassy polymers. Mechanics of Time-Dependent Materials, Society for Experimental Mechanics, 2018, 22 (2), p.145-165 [HAL] / [DOI]
2018Olivier De Almeida, Philippe Olivier. Introduction mise en oeuvre des composites à matrice thermoplastique : préface. Revue des composites et des matériaux avancés, Lavoisier, 2018, Mise en oeuvre des composites à matrice thermoplastique, 28 (1), p.7-8 [HAL]
2018Céline Vicard, Olivier De Almeida, Arthur Cantarel, Gérard Bernhart. Diagramme TTT isotherme de la polymérisation anionique du PA6 à partir de l'epsilon-caprolactame. Revue des composites et des matériaux avancés, Lavoisier, 2018, Mise en oeuvre des composites à matrice thermoplastique, 28 (1), p.89-110 [HAL]
2018Zhorachaid Thanawarothon, Abdelrahman Elmikaty, Christophe Bouvet, Laurent Mezeix. NONCIRCULAR CFRP BICYCLE'S CHAINRING, PART II: FINITE ELEMENT ANALYSIS. Composites: Mechanics, Computations, Applications: An International Journal, 2018, 9 (3), pp.207 - 222 [HAL] / [DOI]
2018Valérie Pommier-Budinger, Marc Budinger, Pierrick Rouset, Fabien Dezitter, Florent Huet, et al. Electro-mechanical Resonant Ice Protection Systems: Initiation of Fractures with Piezoelectric Actuators. AIAA Journal, American Institute of Aeronautics and Astronautics, 2018, pp.0 [HAL] / [DOI]
2018S. Dubreuil, N. Bartoli, Christian Gogu, T. Lefebvre, J. Mas Colomer. Extreme value oriented random field discretization based on an hybrid polynomial chaos expansion — Kriging approach. Computer Methods in Applied Mechanics and Engineering, Elsevier, 2018, 332, pp.540-571 [HAL] / [DOI]
2018Maxime Boulanghien, Mohamed R'Mili, Gérard Bernhart, Florentin Berthet, Yannick Soudais. Mechanical Characterization of Carbon Fibres Recycled by Steam Thermolysis: A Statistical Approach. Advances in Materials Science and Engineering, Hindawi Publishing Corporation, 2018, 2018, art 8630232-10 p [HAL] / [DOI]
2018Renaud Julien, Vincent Velay, Vanessa Vidal, Yoann Dahan, Romain Forestier, et al. Characterization and modeling of forged Ti-6Al-4V Titanium alloy with microstructural considerations during quenching process. International Journal of Mechanical Sciences, Elsevier, 2018, 142-143, pp.456-467 [HAL] / [DOI]
Florian Mitjana, Sonia Cafieri, Florian Bugarin, Christian Gogu, Fabien Castanié. Optimization of structures under buckling constraints using frame elements. Engineering Optimization, Taylor & Francis, In press [HAL]
2018Jamel Saoudi, Redouane Zitoune, Suhasini Gururaja, Mehdi Salem, Salah Mezleni. Analytical and experimental investigation of the delamination during drilling of composite structures with core drill made of diamond grits: X-ray tomography analysis. Journal of Composite Materials, SAGE Publications, 2018, 52 (10), p.1281-1294 [HAL] / [DOI]
2018Hiroaki Matsumoto, Takuro Nishihara, Vincent Velay, Vanessa Vidal. Superplastic Property of the Ti-6Al-4V Alloy with Ultrafine-Grained Heterogeneous Microstructure. Advanced Engineering Materials, Wiley-VCH Verlag, 2018, 20 (1), pp.1700317 [HAL] / [DOI]
2018F. Bourdin, J.C. Stinville, M.P. Echlin, P.G. Callahan, W.C. Lenthe, et al. Measurements of plastic localization by heaviside-digital image correlation. Acta Materialia, Elsevier, 2018, 157, pp.307-325 [HAL] / [DOI]
Mahamadou Mounkaila, Sonia Sassi, Abbas Hamadi, Philippe Marguerès, Philippe Olivier, et al. Modelling the electrical behaviour of carbon/epoxy composites and monitoring changes in their microstructure during oven and autoclave curing using electrical impedancemetry. Smart Materials and Structures, IOP Publishing, In press, [HAL] / [DOI]
2018Fabien Blas, Florence Ansart, Philippe Lours, Jean-Pierre Bonino, Sandrine Duluard, et al. Processing thermal barrier coatings via sol-gel route: Crack network control and durability. Surface and Coatings Technology, Elsevier, 2018, 334, p.71-77 [HAL] / [DOI]
2018Donghai Qiu, Sébastien Seguy, Manuel Paredes. Tuned Nonlinear Energy Sink With Conical Spring: Design Theory and Sensitivity Analysis. Journal of Mechanical Design, American Society of Mechanical Engineers, 2018, 140 (1), [HAL] / [DOI]
2018Pierre-Marie Nigay, Ange Nzihou, Thierry Cutard. The impact of the particle size distribution of organic additives on the microstructure of a clay ceramic and its thermal and mechanical properties . Journal of Materials in Civil Engineering, American Society of Civil Engineers, 2018, 30 (4), pp.04018044 [HAL] / [DOI]
2018Michel Bornert, Pascal Doumalin, Jean-Christophe Dupré, Christophe Poilâne, Laurent Robert, et al. Assessment of Digital Image Correlation Measurement Accuracy in the Ultimate Error Regime: Improved Models of Systematic and Random Errors. Experimental Mechanics, Society for Experimental Mechanics, 2018, 58 (1), p.33-48 [HAL] / [DOI]
2018Jean-Charles Passieux, Robin Bouclier, Jean-Noël Périé. A Space-Time PGD-DIC Algorithm: Application to 3D Mode Shapes Measurements. Experimental Mechanics, Society for Experimental Mechanics, 2018, [HAL] / [DOI]
2018D. Texier, F. Atmani, P. Bocher, F. Nadeau, J. Chen, et al. Fatigue performances of FSW and GMAW aluminum alloys welded joints: Competition between microstructural and structural-contact-fretting crack initiation. International Journal of Fatigue, Elsevier, 2018, 116, pp.20-233 [HAL] / [DOI]
2018Stéphane Guinard, Robin Bouclier, Mateus Toniolli, Jean-Charles Passieux. Multiscale analysis of complex aeronautical structures using robust non-intrusive coupling. Advanced Modeling and Simulation in Engineering Sciences, SpringerOpen, 2018, 5 (1), pp.1 [HAL] / [DOI]
2018John Susainathan, Florent Eyma, Emmanuel De Luycker, Arthur Cantarel, Bruno Castanié. Experimental investigation of impact behavior of wood-based sandwich structures. Composites Part A: Applied Science and Manufacturing, Elsevier, 2018, vol 109, pp 10-19 [HAL] / [DOI]
2018Florian Boutenel, Myriam Delhomme, Vincent Velay, Romain Boman. Finite element modelling of cold drawing for high-precision tubes. Comptes Rendus Mécanique, Elsevier Masson, 2018, 346 (8), pp.665-677 [HAL] / [DOI]
2017Céline Vicard, Olivier De Almeida, Arthur Cantarel, Gérard Bernhart. Experimental study of polymerization and crystallization kinetics of polyamide 6 obtained by anionic ring opening polymerization of ε-caprolactam. Polymer, Elsevier, 2017, 132, p.88 - 97 [HAL] / [DOI]
2017Pierre Planques, Vanessa Vidal, Philippe Lours, Vincent Proton, Fabrice Crabos, et al. Characterization of the mechanical properties of thermal barrier coatings by 3 points bending tests and modified small punch tests. Surface and Coatings Technology, Elsevier, 2017, 332, p.40-46 [HAL] / [DOI]
2017Rémi Gilblas, Thierry Sentenac, Jean-José Orteu, Mickaël Sauvée, Guillaume Sierra, et al. Detection of Micro-Cracks on Highly Specular Reflectors: Dimensioning a Vision Machine Based on Optical Properties. IEEE Sensors Journal, Institute of Electrical and Electronics Engineers, 2017, 17 (23), p.7901 - 7907 [HAL] / [DOI]
2017Joël Serra, Christophe Bouvet, Bruno Castanié, Caroline Petiot. Experimental and numerical analysis of Carbon Fiber Reinforced Polymer notched coupons under tensile loading. Composite Structures, Elsevier, 2017, 181, pp.145-157 [HAL] / [DOI]
2017Bassam Mahmoud, Marcos Torrecilla Colungo, Pablo Navarro, Steven Marguet, Issam Tawk, et al. Semi-continuous strategy for the modelling of damage mechanisms in unidirectional composites under low velocity impacts. Composites Part B: Engineering, Elsevier, 2017, 130, pp.147 - 157 [HAL] / [DOI]
2017Van Hung Bui, Patrick Gilles, Tarek Sultan, Guillaume Cohen, Walter Rubio. A new cutting depth model with rapid calibration in abrasive water jet machining of titanium alloy. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2017, 93 (5-8), pp.1499 - 1512 [HAL] / [DOI]
2017Rami Hamdan, Jérôme Michetti, Claire Dionnet, Franck Diemer, Marie Georgelin-Gurgel. In-vitro evaluation of apical microleakage of two obturation methods of immature permanent teeth: orthograde apical plug of Mineral Trioxide Aggregate and root canal filling combining custom gutta-percha cone with Calcium Silicate-based sealer. GIORNALE ITALIANO DI ENDODONZIA, 2017, 31 (2), pp.89 - 95 [HAL] / [DOI]
2017Yanfeng Gao, Pascale Magaud, Lucien Baldas, Christine Lafforgue, Micheline Abbas, et al. Self-ordered particle trains in inertial microchannel flows. Microfluidics and Nanofluidics, Springer Verlag, 2017, 21 (10), pp.0 [HAL] / [DOI]
2017Srinivas Pinisetty, Thierry Jéron, Stavros Tripakis, Yliès Falcone, Hervé Marchand, et al. Predictive Runtime Verification of Timed Properties. Journal of Systems and Software, Elsevier, 2017, 132, pp.353 - 365 [HAL] / [DOI]
2017Benjamin Vales, Steven Marguet, Romain Créac'Hcadec, Laurent Sohier, Jean-François Ferrero, et al. Experimental & numerical study of the Tensile/Compression-Shear Arcan test under dynamic loading. International Journal of Adhesion and Adhesives, Elsevier, 2017, 78, pp.135 - 147 [HAL] / [DOI]
2017Yves Davila, Laurent Crouzeix, Bernard Douchin, Francis Collombet, Yves-Henri Grunevald. Spatial Evolution of the Thickness Variations over a CFRP Laminated Structure. Applied Composite Materials, Springer Verlag (Germany), 2017, 24 (5), pp.1201 - 1215 [HAL] / [DOI]
2017Marcio Wagner Batista Dos santos, Vincent Velay, Vanessa Vidal, Gérard Bernhart, Gilmar Ferreira Batalha, et al. Mechanical behavior of a Ti-6Al-4 V titanium alloy with microstructural evolution modeling under hot and superplastic conditions. Materials Science and Engineering Technology / Materialwissenschaft und Werkstofftechnik, Wiley-VCH Verlag, 2017, Special Issue: 11th European Conference on Superplastic Forming (EuroSPF) (Selected contributions), 48 (10), p.952-961 [HAL] / [DOI]
2017Ion Hazyuk, Marc Budinger, Florian Sanchez, Christian Gogu. Optimal design of computer experiments for surrogate models with dimensionless variables. Structural and Multidisciplinary Optimization, Springer Verlag (Germany), 2017, 56 (3), pp.663 - 679 [HAL] / [DOI]
2017Tao Li, Donghai Qiu, Sébastien Seguy, Alain Berlioz. Activation characteristic of a vibro-impact energy sink and its application to chatter control in turning. Journal of Sound and Vibration, Elsevier, 2017, 405, pp.1 - 18 [HAL] / [DOI]
2017Pierre Planques, Vanessa Vidal, Philippe Lours, Vincent Proton, Fabrice Crabos, et al. Mechanical and thermo-physical properties of plasma-sprayed thermal barrier coatings: a literature survey. Oxidation of Metals, Springer Verlag, 2017, vol 88 (n° 1-2), p.133-143 [HAL] / [DOI]
2017M. -Q. Thai, F. Schmidt, Gilles Dusserre, Arthur Cantarel, L. Silva. BEM computation of 3D Stokes flow including moving front. International Journal of Material Forming, Springer Verlag, 2017, 10 (4), p 567-580 [HAL] / [DOI]
2017Robin Bouclier, Jean-Charles Passieux. A domain coupling method for finite element digital image correlation with mechanical regularization: Application to multiscale measurements and parallel computing. International Journal for Numerical Methods in Engineering, Wiley, 2017, 111 (2), pp.123 - 143 [HAL] / [DOI]
2017Aurélien Fabas, Aurélie Rouaix-Vande Put, Sébastien Doublet, Didier Domergue, Mehdi Salem, et al. Metal dusting corrosion of austenitic alloys at low and high pressure with the effects of Cr, Al, Nb and Cu. Corrosion Science, Elsevier, 2017, 123, p 310-318 [HAL] / [DOI]
2017Pamela Vocale, Gian Luca Morini, Marco Spiga, Stéphane Colin. Shear work contribution to convective heat transfer of dilute gases in slip flow regime. European Journal of Mechanics - B/Fluids, Elsevier, 2017, 64, pp.60 - 68 [HAL] / [DOI]
2017Hiroaki Matsumoto, Vincent Velay. Mesoscale modeling of dynamic recrystallization behavior, grain size evolution, dislocation density, processing map characteristic, and room temperature strength of Ti-6Al-4V alloy forged in the (α+β) region. Journal of Alloys and Compounds, Elsevier, 2017, 708, pp.404 - 413 [HAL] / [DOI]
2017Victor Achard, Alain Daidié, Manuel Paredes, Clément Chirol. Optimization of the Cold Expansion Process for Titanium Holes . Advanced Engineering Materials, Wiley-VCH Verlag, 2017, 19 (6), [HAL] / [DOI]
2017G. Tatsios, G. Lopez Quesada, Marcos Rojas-Cárdenas, Lucien Baldas, Stéphane Colin, et al. Computational investigation and parametrization of the pumping effect in temperature-driven flows through long tapered channels. Microfluidics and Nanofluidics, Springer Verlag, 2017, 21 (5), 99 (17 p.) [HAL] / [DOI]
2017Marcos Rojas-Cárdenas, Ernane Silva, Minh-Tuan Ho, César Deschamps, Irina Graur. Time-dependent methodology for non-stationary mass flow rate measurements in a long micro-tube. Microfluidics and Nanofluidics, Springer Verlag, 2017, 21 (5), [HAL] / [DOI]
2017Hacene Si Hadj Mohand, Aldo Frezzotti, Juergen Brandner, Stéphane Colin, Christine Barrot. Molecular tagging velocimetry by direct phosphorescence in gas microflows: Correction of Taylor dispersion. Experimental Thermal and Fluid Science, Elsevier, 2017, 83, pp.177 - 190 [HAL] / [DOI]
2017Frederic Monies, Isabelle Danis, Christian Bes, Sonia Cafieri, Marcel Mongeau. A new machining strategy for roughing deep pockets of magnesium-rare earth alloys. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2017, 92, pp.3883-3901 [HAL] / [DOI]
2017N. Dubary, G. Taconet, Christophe Bouvet, B. Vieille. Influence of temperature on the impact behavior and damage tolerance of hybrid woven-ply thermoplastic laminates for aeronautical applications. Composite Structures, Elsevier, 2017, 168, pp.663 - 674 [HAL] / [DOI]
2017Michel Bornert, Pascal Doumalin, Jean-Christophe Dupré, Christophe Poilâne, Laurent Robert, et al. Shortcut in DIC error assessment induced by image interpolation used for subpixel shifting. Optics and Lasers in Engineering, Elsevier, 2017, 91, pp.124-133 [HAL] / [DOI]
2017Akshay Hejjaji, Redouane Zitoune, Laurent Crouzeix, Sabine Le Roux, Francis Collombet. Surface and machining induced damage characterization of abrasive water jet milled carbon/epoxy composite specimens and their impact on tensile behavior. Wear, Elsevier, 2017, 376-377 (Part B), p 1356-1364 [HAL] / [DOI]
2017T. Li, E. Gourc, Sébastien Seguy, Alain Berlioz. Dynamics of two vibro-impact nonlinear energy sinks in parallel under periodic and transient excitations. International Journal of Non-Linear Mechanics, Elsevier, 2017, 90, pp.100 - 110 [HAL] / [DOI]
2017O. Shtehin, V. Wagner, Sébastien Seguy, Yann Landon, G. Dessein, et al. Stability of ball-end milling on warped surface: semi-analytical and experimental analysis. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2017, 89 (9-12), pp.2557 - 2569 [HAL] / [DOI]
2017Christophe Rouzaud, Fabrice Gatuingt, Guillaume Hervé, Olivier Dorival. A new multi-frequency approach based on Padé approximants for the treatment of transient dynamics problems with the variational theory of complex rays. Journal of Sound and Vibration, Elsevier, 2017, 392, pp.170-186 [HAL] / [DOI]
2017Kejian Li, Gabriel Spartacus, Jiling Dong, Pengjun Cao, Keesam Shin. Effect of ultrasonic shot peening on microstructure and properties of 301SS. Materials and Manufacturing Processes, Taylor & Francis, 2017, 32 (16), p.1851-1855 [HAL] / [DOI]
2017Francois Louf, Sami Daouk, Christophe Cluzel, Olivier Dorival, Laurent Champaney, et al. Study of the dynamic behavior of a bolted joint under heavy loadings. Journal of Sound and Vibration, Elsevier, 2017, 392, pp.307 - 324 [HAL] / [DOI]
2017Yankuan Liu, Yinghui Liu, Philippe Lours, Thierry Sentenac, Vanessa Vidal, et al. Influence of isothermal aging conditions on APS TBC's interfacial fracture toughness. Surface and Coatings Technology, Elsevier, 2017, 313, pp.417-424 [HAL] / [DOI]
2017Tao Li, Sébastien Seguy, Alain Berlioz. Optimization mechanism of targeted energy transfer with vibro-impact energy sink under periodic and transient excitation. Nonlinear Dynamics, Springer Verlag, 2017, 87 (4), pp.2415 - 2433 [HAL] / [DOI]
2017P. M. Nigay, Thierry Cutard, Ange Nzihou. The impact of heat treatment on the microstructure of a clay ceramic and its thermal and mechanical properties. Ceramics International, Elsevier, 2017, 43 (2), p.1747-1754 [HAL] / [DOI]
2017M. F. Ameur, M. Habak, M. Kenane, H. Aouici, Mohammed Cheikh. Machinability analysis of dry drilling of carbon/epoxy composites: cases of exit delamination and cylindricity error. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2017, 88 (9), p 2557-2571 [HAL] / [DOI]
2017Tao Li, Sébastien Seguy, Alain Berlioz. On the dynamics around targeted energy transfer for vibro-impact nonlinear energy sink. Nonlinear Dynamics, Springer Verlag, 2017, 87 (3), pp.1453 - 1466 [HAL] / [DOI]
2017Teddy Lisle, Marie-Laetitia Pastor, Christophe Bouvet, Philippe Marguerès. Damage of woven composite under translaminar cracking tests using infrared thermography. Composite Structures, Elsevier, 2017, vol 161, pp 275-286 [HAL] / [DOI]
2017M. S. Bin Mohamed Rehan,, Jérôme Rousseau, Stéphane Fontaine, Xiaojing Gong. Experimental study of the influence of ply orientation on DCB mode-I delamination behavior by using multidirectional fully isotropic carbon/epoxy laminates. Composite Structures, Elsevier, 2017, 161, pp.1-7 [HAL] / [DOI]
2017I Alhossen, F Villeneuve-Faure, F. Baudoin, Florian Bugarin, Stéphane Segonds. Sensitivity analysis of the electrostatic force distance curve using Sobol’s method and design of experiments. Journal of Physics D: Applied Physics, IOP Publishing, 2017, 50 (3), [HAL] / [DOI]
2017Giuseppe Pennisi, Cyrille Stephan, Etienne Gourc, Guilhem Michon. Experimental investigation and analytical description of a vibro-impact NES coupled to a single-degree-of-freedom linear oscillator harmonically forced. Nonlinear Dynamics, Springer Verlag, 2017, 88 (3), pp.1769 - 1784 [HAL] / [DOI]
2017Naomi Murdoch, Iris Avila Martinez, Cecily Sunday, Emmanuel Zenou, Olivier Cherrier, et al. An experimental study of low-velocity impacts into granular material in reduced gravity. Monthly Notices of the Royal Astronomical Society, Oxford University Press (OUP): Policy P - Oxford Open Option A, 2017, vol 468 (n° 2), pp 1259-1272 [HAL] / [DOI]
2017Pierre-Marie Nigay, Rababe Sani, Thierry Cutard, Ange Nzihou. Modeling of the thermal and mechanical properties of clay ceramics incorporating organic additives. Materials Science and Engineering: A, Elsevier, 2017, 708, p.375-382 [HAL] / [DOI]
2017R. Julien, Vincent Velay, V. Vidal, Y. Dahan, R. Forestier, et al. Tensile behaviour of high temperature forged Ti-6Al-4V during in-situ heat treatments. Materials Letters, Elsevier, 2017, 208, p 7-9 [HAL] / [DOI]
2017Matthias Barus, Hélène Welemane, Francis Collombet, Marie-Laetitia Pastor, Arthur Cantarel, et al. Bonded repair issues for composites: An investigation approach based on infrared thermography. NDT and E International, Elsevier, 2017, 85, pp.27-33 [HAL] / [DOI]
2017Camille Bessaguet, Eric Dantras, Colette Lacabanne, Mathieu Chevalier, Guilhem Michon. Piezoelectric and mechanical behavior of NaNbO3/PEKK lead-free nanocomposites. Journal of Non-Crystalline Solids, Elsevier, 2017, 459, pp.83-87 [HAL] / [DOI]
2017Igor Jovančević, Huy-Hieu Pham, Jean-José Orteu, Rémi Gilblas, Jacques Harvent, et al. 3D Point Cloud Analysis for Detection and Characterization of Defects on Airplane Exterior Surface. Journal of Nondestructive Evaluation, Springer Verlag, 2017, 36 (4), pp.74 [HAL] / [DOI]
2017Laurent Mezeix, Simon Dols, Christophe Bouvet, Bruno Castanié, Jean-Paul Giavarini, et al. Experimental analysis of impact and post-impact behaviour of inserts in Carbon sandwich structures. Journal of Sandwich Structures and Materials, SAGE Publications, 2017, pp.0 [HAL] / [DOI]
2017Imen Ksouri, Olivier De Almeida, Nader Haddar. Long term ageing of polyamide 6 and polyamide 6 reinforced with 30% of glass fibers: physicochemical, mechanical and morphological characterization. Journal of Polymer Research, Springer Verlag, 2017, 24 (8), art.133 - 12 p [HAL] / [DOI]
2017Stéphane Segonds, Philippe Seitier, Cyril Bordreuil, Florian Bugarin, Walter Rubio, et al. An analytical model taking feed rate effect into consideration for scallop height calculation in milling with torus-end cutter. Journal of Intelligent Manufacturing, Springer Verlag (Germany), 2017, [HAL] / [DOI]
2017Jacques Poirier, Eric Blond, Emmanuel De Bilbao, Rudy Michel, Antoine Coulon, et al. New advances in the laboratory characterization of refractories : testing and modelling. Metallurgical Research & Technology, EDP Sciences, 2017, 114 (6), art 610 - 16 p [HAL] / [DOI]
2017Robin Bouclier, Jean-Charles Passieux, Michel Salaün. Development of a new, more regular, mortar method for the coupling of NURBS subdomains within a NURBS patch: Application to a non-intrusive local enrichment of NURBS patches. Computer Methods in Applied Mechanics and Engineering, Elsevier, 2017, 316, pp.123-150 [HAL] / [DOI]
2017Ankit Chiplunkar, Emmanuel Rachelson, Michele Colombo, Joseph Morlier. Approximate inference in related multi-output Gaussian Process Regression. Lecture Notes in Computer Science, Springer, 2017, pp.88-103 [HAL] / [DOI]
2017Igor Jovančević, Huy-Hieu Pham, Jean-José Orteu, Rémi Gilblas, Jacques Harvent, et al. Détection et caractérisation de défauts de surface par analyse des nuages de points 3D fournis par un scanner. Instrumentation, Mesure, Métrologie, Lavoisier, 2017, 16 (1-4), p.261-282 [HAL]
2017Marie Adou-Assoumou, Aline Krah-Sinan, Yolande Koffi-Gnagne, K Bane, B Faye, et al. Protocol for Root Canals' Irrigation in Endodontic Practice in Ivory Coast: A Survey of 100 Dentists. Journal of Dentistry and Oral Care Medicine, 2017, 3, pp.303 - 303 [HAL]
2017Rami Hamdan, Jérôme Michetti, Deborah Pinchon, Franck Diemer, Marie Georgelin-Gurgel. The XP-Endo Finisher for the removal of calcium hydroxide paste from root canals and from the apical third. Journal of Clinical and Experimental Dentistry, 2017, 9, pp.0 - 0 [HAL] / [DOI]
2017Fenglin Liang, Martial Sauceau, Gilles Dusserre, Patricia Arlabosse. A uniaxial cyclic compression method for characterizing the rheological and textural behaviors of mechanically dewatered sewage sludge. Water Research, IWA Publishing, 2017, 113, pp.171-180 [HAL] / [DOI]
2017Juan Loukota, Jean-Charles Passieux, Albert Lucchetti, Guilhem Michon. Modeling of Nonstructural Components in the Dynamic Behavior of Aeronautical Structures. Journal of Aircraft, American Institute of Aeronautics and Astronautics, 2017, 54 (1), pp.85-93 [HAL] / [DOI]
2017Florentin Berthet, Frederic Lachaud, Jérémy Crevel, Marie-Laetitia Pastor. Behaviour and damage of injected carbon-fibre-reinforced polyether ether ketone: From process to modelling. Journal of Composite Materials, SAGE Publications, 2017, 51 (2), p 141-151 [HAL] / [DOI]
2017Etienne Copin, X. Massol, Stéphane Amiel, Thierry Sentenac, Yannick Le Maoult, et al. Novel erbia-yttria co-doped zirconia fluorescent thermal history sensor. Smart Materials and Structures, IOP Publishing, 2017, 26 (1), art 015001-11 p [HAL] / [DOI]
2017Eric Paroissien, Frederic Lachaud, Sébastien Schwartz, Anthony Da Veiga, Patrick Barrière. Simplified stress analysis of hybrid (bolted/bonded) joints. International Journal of Adhesion and Adhesives, Elsevier, 2017, 77, pp.183-197 [HAL] / [DOI]
2017Florian Sanchez, Marc Budinger, Ion Hazyuk. Dimensional analysis and surrogate models for the thermal modeling of Multiphysics systems. Applied Thermal Engineering, Elsevier, 2017, 110 (3), pp.758-771 [HAL] / [DOI]
2017Jean-Emmanuel Pierré, Jean-Charles Passieux, Jean-Noël Périé. Finite Element Stereo Digital Image Correlation: Framework and Mechanical Regularization. Experimental Mechanics, Society for Experimental Mechanics, 2017, 57 (3), p.443-456 [HAL] / [DOI]
2017Mahmoud Harzallah, Thomas Pottier, Johanna Senatore, Michel Mousseigne, Guénaël Germain, et al. Numerical and experimental investigations of Ti-6Al-4V chip generation and thermo-mechanical couplings in orthogonal cutting. International Journal of Mechanical Sciences, Elsevier, 2017, 134, p.189-202 [HAL] / [DOI]
2017John Susainathan, Florent Eyma, Emmanuel De Luycker, Arthur Cantarel, Bruno Castanié. Manufacturing and quasi-static bending behavior of wood-based sandwich structures. Composite Structures, Elsevier, 2017, 182, pp.487-504 [HAL] / [DOI]
2017Joël Serra, Jean-Emmanuel Pierré, Jean-Charles Passieux, Jean-Noël Périé, Christophe Bouvet, et al. Validation and modeling of aeronautical composite structures subjected to combined loadings: The VERTEX project. Part 1: Experimental setup, FE-DIC instrumentation and procedures Composite Structures, Elsevier, 2017, 179, p.224-244 [HAL] / [DOI]
2017Mathieu Fogel, Patricia Parlevliet, Philippe Olivier, Eric Dantras. Manufacturing of conductive structural composites through spraying of CNTs/epoxy dispersions on dry carbon fiber plies. Composites Part A: Applied Science and Manufacturing, Elsevier, 2017, vol 100, pp 40-47 [HAL] / [DOI]
2017Joël Serra, Jean-Emmanuel Pierré, Jean-Charles Passieux, Jean-Noël Périé, Christophe Bouvet, et al. Validation and modeling of aeronautical composite structures subjected to combined loadings: The VERTEX project. Part 2: Load envelopes for the assessment of panels with large notches Composite Structures, Elsevier, 2017, 180, pp.550-567 [HAL] / [DOI]
2016Vincent Velay, Abderrahim Michrafy. An analytical model for the prediction of hot roll temperatures in a hot rolling process. Materials Science and Engineering Technology / Materialwissenschaft und Werkstofftechnik, Wiley-VCH Verlag, 2016, 47 (12), p 1202-1215 [HAL] / [DOI]
2016Cédric Pozzolini, Yves Renard, Michel Salaün. Energy conservative finite element semi-discretization for vibro-impacts of plates on rigid obstacles. ESAIM: Mathematical Modelling and Numerical Analysis, EDP Sciences, 2016, vol 50 (n° 6), pp 1585-1613 [HAL] / [DOI]
2016Fabien Destic, Christophe Bouvet. Impact damages detection on composite materials by THz imaging. Case Studies in Nondestructive Testing and Evaluation, 2016, 6, pp.53-62 [HAL] / [DOI]
2016Alexia Vinel, Aline Sinan, Melanie Dedieu, Sara Laurencin Dalicieux, Franck Diemer, et al. Effect of apical preparation on different needle depth penetration. GIORNALE ITALIANO DI ENDODONZIA, 2016, 30 (2), pp.96 - 100 [HAL] / [DOI]
2016Michel Galaup, Catherine Pons lelardeux, Pierre Lagarrigue. Un learning game au carrefour des institutions partenaires : Mecagenius®. RDST (En ligne), Éditions de l’École normale supérieure de Lyon, 2016, pp.51 - 69 [HAL] / [DOI]
2016Benjamin Ostré, Christophe Bouvet, Clément Minot, Jacky Aboissière. Finite Element analysis of CFRP laminates subjected to compression after edge impact. Composite Structures, Elsevier, 2016, vol 153, pp 478-489 [HAL] / [DOI]
2016L. V. Korah, P. M. Nigay, Thierry Cutard, Ange Nzihou, S. Thomas. The impact of the particle shape of organic additives on the anisotropy of a clay ceramic and its thermal and mechanical properties. Construction and Building Materials, Elsevier, 2016, 125, p 654-660 [HAL] / [DOI]
2016Ahmed Zouaghi, Vincent Velay, Adriana Soveja, Thomas Pottier, Mohammed Cheikh, et al. A multi-scale approach to investigate the non linear subsurface behavior and strain localization of X38CrMoV5-1 martensitic tool steel: experiment and numerical analysis. International Journal of Plasticity, Elsevier, 2016, 87, pp.130-153 [HAL] / [DOI]
2016Abdelhamid Maali, Stéphane Colin, Bharat Bhushan. Slip length measurement of gas flow. Nanotechnology, Institute of Physics, 2016, 27 (37), pp.374004 (1-12) [HAL] / [DOI]
2016D'Elia Raffaele, Gérard Bernhart, Jouke Hijlkema, Thierry Cutard. Experimental analysis of SiC-based refractory concrete in hybrid rocket nozzles. Acta Astronautica, Elsevier, 2016, 126 (SI), p 168-177 [HAL] / [DOI]
2016Rémi Gilblas, Thierry Sentenac. Effect and correction of the shift in spectral images for polychromatic thermography. International Journal of Thermal Sciences, Elsevier, 2016, 107, p 153-160 [HAL] / [DOI]
2016Hakim Abdulhamid, Christophe Bouvet, Laurent Michel, Jacky Aboissière, Clément Minot. Numerical simulation of impact and compression after impact of asymmetrically tapered laminated CFRP. International Journal of Impact Engineering, Elsevier, 2016, vol 95, pp 154-164 [HAL] / [DOI]
2016Adrien Barrot, Manuel Paredes, Marc Sartor. Determining both radial pressure distribution and torsional stiffness of involute spline couplings. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, SAGE Publications, 2016, 220 (12), pp.1727 - 1738 [HAL] / [DOI]
2016Gilles Dusserre, Olivier Valentin, Fabien Nazaret, Thierry Cutard. Experimental and numerical investigation of the asymmetric primary creep of a fibre reinforced refractory concrete at 1200 degrees C. Journal of the European Ceramic Society, Elsevier, 2016, 36 (10), p. 2627-2639 [HAL] / [DOI]
2016Cecily Sunday, Naomi Murdoch, Olivier Cherrier, Sara Morales Serrano, Claudia Valeria Nardi, et al. A novel facility for reduced-gravity testing: A setup for studying low-velocity collisions into granular surfaces. Review of Scientific Instruments, American Institute of Physics, 2016, 87 (8), pp.084504 [HAL] / [DOI]
2016Ahmed Ktari, Nader Haddar, Farhad Rezai-Aria, Hassine Ferid Ayedi. On the assessment of train crankshafts fatigue life based on LCF tests and 2D-FE evaluation of J-integral. Engineering Failure Analysis, Elsevier, 2016, 66, pp.354-364 [HAL] / [DOI]
2016Hakim Abdulhamid, Christophe Bouvet, Laurent Michel, Jacky Aboissière, Clément Minot. Experimental study of compression after impact of asymmetrically tapered composite laminate. Composite Structures, Elsevier, 2016, vol 149, pp 292-303 [HAL] / [DOI]
2016Mohammed-Yassine Nagazi, Giovanni Brambilla, Gérard Meunier, Philippe Marguerès, Jean-Noël Périé, et al. Space-resolved diffusing wave spectroscopy measurements of the macroscopic deformation and the microscopic dynamics in tensile strain tests. Optics and Lasers in Engineering, Elsevier, 2016, 88, pp 5 - 12 [HAL] / [DOI]
2016Joël Serra, Christophe Bouvet, Bruno Castanié, Caroline Petiot. Scaling effect in notched composites: The Discrete Ply Model approach. Composite Structures, Elsevier, 2016, 148, pp.127-143 [HAL] / [DOI]
2016C Rouzaud, Fabrice Gatuingt, G Hervé, Olivier Dorival, Nadim Moussallam. Application Of The Variational Theory Of Complex Rays To The Determination Of Shock Induced Vibration Of A Rc Structure. International Journal of Safety and Security Engineering, WIT Press, 2016, 6 (2), pp.427-437 [HAL] / [DOI]
2016Andre Chateau Akue Asseko, Benoît Cosson, Eric Lafranche, Fabrice Schmidt, Yannick Le Maoult. Effect of the developed temperature field on the molecular interdiffusion at the interface in infrared welding of polycarbonate composites. Composites Part B: Engineering, Elsevier, 2016, 97, p 53-61 [HAL] / [DOI]
2016Tao Li, Sébastien Seguy, Alain Berlioz. Dynamics of Cubic and Vibro-Impact Nonlinear Energy Sink: Analytical, Numerical, and Experimental Analysis. Journal of Vibration and Acoustics, American Society of Mechanical Engineers, 2016, 138 (3), [HAL] / [DOI]
2016Lokman Bennani, Philippe Villedieu, Michel Salaün. A mixed adhesion–brittle fracture model and its application to the numerical study of ice shedding mechanisms. Engineering Fracture Mechanics, Elsevier, 2016, vol 158, pp 59-80 [HAL] / [DOI]
2016Ernane Silva, Marcos Rojas-Cárdenas, Cesar Deschamps. Experimental analysis of velocity slip at the wall for gas flows of nitrogen, R134a, and R600a through a metallic microtube. International Journal of Refrigeration, Elsevier, 2016, 66, pp.121 - 132 [HAL] / [DOI]
2016Redouane Zitoune, V. Krishnaraj, Francis Collombet, Sabine Le Roux. Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks. Composite Structures, Elsevier, 2016, 146, p 148-158 [HAL] / [DOI]
2016Mohamed Amine Bouhlel, Nathalie Bartoli, Abdelkader Otsmane, Joseph Morlier. Improving kriging surrogates of high-dimensional design models by Partial Least Squares dimension reduction. Structural and Multidisciplinary Optimization, Springer Verlag (Germany), 2016, vol 53 (n° 5), pp 935-952 [HAL] / [DOI]
2016Marc Budinger, Valérie Pommier-Budinger, Gael Napias, Arthur Costa da Silva. Ultrasonic Ice Protection Systems: Analytical and Numerical Models for Architecture Tradeoff. Journal of Aircraft, American Institute of Aeronautics and Astronautics, 2016, 53 (3), pp.680 - 690 [HAL] / [DOI]
2016Vincent Velay, H. Matsumoto, V. Vidal, A. Chiba. Behavior modelling and microstructural evolutions of Ti-6Al-4V alloy under hot forming conditions. International Journal of Mechanical Sciences, Elsevier, 2016, 108-109, pp.1-13 [HAL] / [DOI]
2016Faisal Qayyum, Masood Shah, Osama Shakeel, Fariha Mukhtar, Mehdi Salem, et al. Numerical simulation of thermal fatigue behavior in a cracked disc of AISI H-11 tool steel. Engineering Failure Analysis, Elsevier, 2016, 62, pp.242-263 [HAL] / [DOI]
2016Raffaele D'Elia, Gilles Dusserre, Sylvie Del Confetto, Nicolas Eberling-Fux, Cedric Descarnps, et al. Cure kinetics of a polysilazane system: Experimental characterization and numerical modelling. European Polymer Journal, Elsevier, 2016, 76, p 40-52 [HAL] / [DOI]
2016Robin Bouclier, Jean-Charles Passieux, Michel Salaün. Local enrichment of NURBS patches using a non-intrusive coupling strategy: Geometric details, local refinement, inclusion, fracture. Computer Methods in Applied Mechanics and Engineering, Elsevier, 2016, 300, pp.1-26 [HAL] / [DOI]
2016Mickaël Duval, Jean-Charles Passieux, Michel Salaün, Stéphane Guinard. Non-intrusive coupling: recent advances and scalable nonlinear domain decomposition. Archives of Computational Methods in Engineering, Springer Verlag, 2016, 23 (1), pp.17-38 [HAL] / [DOI]
2016Benjamin Vales, Steven Marguet, Romain Créach’cadec, Laurent Sohier, Jean-François Ferrero, et al. Numerical study of the local behaviour of adhesive bonds under dynamic loading. Journal of Adhesion Science and Technology, Taylor & Francis, 2016, 30 (12), pp.1319 - 1339 [HAL] / [DOI]
2016Jean-Emmanuel Pierré, Jean-Charles Passieux, Jean-Noël Périé, Florian Bugarin, Laurent Robert. Unstructured finite element-based digital image correlation with enhanced management of quadrature and lens distortions. Optics and Lasers in Engineering, Elsevier, 2016, 77, pp.44-53 [HAL] / [DOI]
2016L. Mezeix, D. Poquillon, C. Bouvet. Entangled Cross-Linked Fibres for an Application as Core Material for Sandwich Structures - Part II: Analytical Model. Applied Composite Materials, Springer Verlag (Germany), 2016, 23 (1), pp.87 - 100 [HAL] / [DOI]
2016Olivier Dorival, Pablo Navarro, Steven Marguet, Caroline Petiot, Michel Bermudez, et al. Experimental results of medium velocity impact tests for reinforced foam core braided composite structures. Journal of Sandwich Structures and Materials, SAGE Publications, 2016, [HAL] / [DOI]
2016Elsa Piollet, Dominique Poquillon, Guilhem Michon. Dynamic hysteresis modelling of entangled cross-linked fibres in shear. Journal of Sound and Vibration, Elsevier, 2016, 383, pp.248-264 [HAL] / [DOI]
2016Natassia Lona Batista, Philippe Olivier, Gérard Bernhart, Mirabel Cerqueira Rezende, Edson Cocchieri Botelho. Correlation between degree of crystallinity, morphology and mechanical properties of PPS/carbon fiber laminates. Materials Research, ABM, ABC, ABPol, SBCC, SBCr, SBMM, SBPMat, 2016, 19 (1), p 195-201 [HAL] / [DOI]
2016Aurélien Fabas, Daniel Monceau, Claudie Josse, Pascal Lamesle, Aurélie Rouaix-Vande Put. Mechanism of metal dusting corrosion by pitting of a chromia-forming alloy at atmospheric pressure and low gas velocity. Corrosion Science, Elsevier, 2016, 107, pp.204-210 [HAL] / [DOI]
2016Fazila Mohd Zawawi, Peng Lv, Sebastien Prothin, Joseph Morlier, Emmanuel Bénard, et al. Performance Enhancement of Tilt-Body Micro Air Vehicle by Use of Orthotropic Laminated Proprotors. Applied Mechanics and Materials, Trans Tech Publications, 2016, vol 819, pp 585-590 [HAL] / [DOI]
2016Damien Mauduit, Gilles Dusserre, Thierry Cutard. Probabilistic rupture analysis of a brittle spray deposited Si–Al alloy under thermal gradient: Characterization and thermoelastic sizing guidelines. Materials and Design, Elsevier, 2016, 95, p 441-421 [HAL] / [DOI]
2016Yangyang Ge, Xiaojing Gong, Anita Hurez, Emmanuel De Luycker. Test methods for measuring pure mode III delamination toughness of composite. Polymer Testing, Elsevier, 2016, 55, pp.261-268 [HAL] / [DOI]
2016Jie Chen, Stefan Stefanov, Lucien Baldas, Stéphane Colin. Analysis of flow induced by temperature fields in ratchet-like microchannels by Direct Simulation Monte Carlo. International Journal of Heat and Mass Transfer, Elsevier, 2016, 99, pp.672-680 [HAL] / [DOI]
2016Mudaser Ullah, Chuan Song Wu, Masood Shah. In situ delta ferrite estimation and their effects on FCPR at different orientations of multipass shielded metal arc welded SS304L. Journal of Manufacturing Processes, Society of Manufacturing Engineers, 2016, 21, p 107-123 [HAL] / [DOI]
2016Xavier Giraud, Marc Budinger, Xavier Roboam, Hubert Piquet, Marc Sartor, et al. Optimal design of the Integrated Modular Power Electronics Cabinet. Aerospace Science and Technology, Elsevier, 2016, 48, pp.37 - 52 [HAL] / [DOI]
2016Lisa Rivière, Antoine Lonjon, Eric Dantras, Colette Lacabanne, Philippe Olivier, et al. Silver fillers aspect ratio influence on electrical and thermal conductivity in PEEK/Ag nanocomposites. European Polymer Journal, Elsevier, 2016, 85, pp.115-125 [HAL] / [DOI]
2016Mohamed Amine Bouhlel, Nathalie Bartoli, Abdelkader Ostmane, Joseph Morlier. An improved approach for estimating the hyperparameters of the kriging model for high-dimensional problems through the partial least squares method. Mathematical Problems in Engineering, Hindawi Publishing Corporation, 2016, 2016, pp.1-11 [HAL] / [DOI]
2016Bilal Karabagli, Thierry Simon, Jean-José Orteu. A new chain-processing-based computer vision system for automatic checking of machining set-up - Application for machine tools safety. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2016, 82 (9), [HAL] / [DOI]
2016C Rouzaud, Fabrice Gatuingt, G Hervé, N Moussallam, Olivier Dorival. Influence of the aircraft crash induced local nonlinearities on the overall dynamic response of a RC structure through a parametric study. Nuclear Engineering and Design, Elsevier, 2016, [HAL] / [DOI]
2016Victor Munoz, Benjamin Vales, Marianne Perrin, Marie-Laetitia Pastor, Hélène Welemane, et al. Damage detection in CFRP by coupling acoustic emission and infrared thermography. Composites Part B: Engineering, Elsevier, 2016, 85, pp.68-75 [HAL] / [DOI]
2016Benjamin Ostré, Christophe Bouvet, Clément Minot, Jacky Aboissière. Experimental analysis of CFRP laminates subjected to compression after edge impact. Composite Structures, Elsevier, 2016, 152, pp.767-778 [HAL] / [DOI]
2016Benjamin Vales, Victor Munoz Cuartas, Hélène Welemane, Marie-Laetitia Pastor, Baptiste Trajin, et al. Heat source estimation in anisotropic materials. Composite Structures, Elsevier, 2016, 136, pp.287-296 [HAL] / [DOI]
2016Sonia Cafieri, Frederic Monies, Marcel Mongeau, Christian Bes. Plunge milling time optimization via mixed-integer nonlinear programming. Computers and Industrial Engineering, Elsevier, 2016, 98, pp.434-445 [HAL] / [DOI]
2015Aldo Frezzotti, Hacene Si Hadj Mohand, Christine Barrot, Stéphane Colin. Role of diffusion on molecular tagging velocimetry technique for rarefied gas flow analysis. Microfluidics and Nanofluidics, Springer Verlag, 2015, 19 (6), pp.1335 - 1348 [HAL] / [DOI]
2015Y. Liu, V. Vidal, Sabine Le Roux, Fabien Blas, F. Ansart, et al. Influence of isothermal and cyclic oxidation on the apparent interfacial toughness in thermal barrier coating systems. Journal of the European Ceramic Society, Elsevier, 2015, 35 (15), p 4269-4275 [HAL] / [DOI]
2015Ilisio Viana, Jean-José Orteu, Nicolas Cornille, Florian Bugarin. Inspection of aeronautical mechanical parts with a pan-tilt-zoom camera: an approach guided by the computer-aided design model. Journal of Electronic Imaging, SPIE and IS&T, 2015, 24 (6), pp.061118 [HAL] / [DOI]
2015Zeeshan Anjum, Faisal Qayyum, Shahab Khushnood, Sagheer Ahmed, Masood Shah. Prediction of non-propagating fretting fatigue cracks in Ti6Al4V sheet tested under pin-in-dovetail configuration: Experimentation and numerical simulation. Materials and Design, Elsevier, 2015, 87, p 750-758 [HAL] / [DOI]
2015Florian Pascal, Pablo Navarro, Steven Marguet, Jean-François Ferrero. On the modelling of low to medium velocity impact onto woven composite materials with a 2D semi-continuous approach. Composite Structures, Elsevier, 2015, 134, pp.302 - 310 [HAL] / [DOI]
2015Aurelien Reysset, Marc Budinger, Jean-Charles Maré. Computer-aided definition of sizing procedures and optimization problems of mechatronic systems. Concurrent Engineering: Research and Applications, SAGE Publications, 2015, 23 (4), pp.320 - 332 [HAL] / [DOI]
2015Masood Shah, Catherine Mabru, Manel Baccar, Farhad Rezai-Aria. Normalization of fatigue crack growth data in AISI H11 tool steel at room and elevated temperature. International Journal of Damage Mechanics, 2015, 24 (8), pp.1111-1140 [HAL] / [DOI]
2015Christophe Cluzel, Philippe Rouch, Olivier Dorival, Stéphanie Behar. Experimental identification and associated model of the dissipation in the electric cables of a satellite structure. Journal of Sound and Vibration, Elsevier, 2015, 357, pp.156-167 [HAL] / [DOI]
2015Christophe Rouzaud, Fabrice Gatuingt, Olivier Dorival, Hervé Guillaume, Louis Kovalevsky. A new methodology for assessing the global dynamic response of large shell structures under impact loading. Engineering Computations, Emerald, 2015, 32 (8), pp.2343-2382 [HAL] / [DOI]
2015Pierre-Jacques Liotier, Quentin Govignon, Elinor Swery, Sylvain Drapier, Simon Bickerton. Characterisation of woven flax fibres reinforcements: Effect of the shear on the in-plane permeability. Journal of Composite Materials, SAGE Publications, 2015, 49 (27), pp.3415-3430 [HAL] / [DOI]
2015Igor Jovančević, Stanislas Larnier, Jean-José Orteu, Thierry Sentenac. Automated exterior inspection of an aircraft with a pan-tilt-zoom camera mounted on a mobile robot . Journal of Electronic Imaging, SPIE and IS&T, 2015, 24 (6), pp.061110 [HAL] / [DOI]
2015Andre Chateau Akue Asseko, Benoît Cosson, Fabrice Schmidt, Yannick Le Maoult, Rémi Gilblas, et al. Laser transmission welding of composites - Part B: Experimental validation of numerical model. Infrared Physics and Technology, Elsevier, 2015, 73, p 304-311 [HAL] / [DOI]
2015E. Gourc, Sébastien Seguy, Guilhem Michon, Alain Berlioz, B.P. Mann. Quenching chatter instability in turning process with a vibro-impact nonlinear energy sink. Journal of Sound and Vibration, Elsevier, 2015, 355, pp.392 - 406 [HAL] / [DOI]
2015Serge Abrate, Jean-François Ferrero, Pablo Navarro. Cohesive zone models and impact damage predictions for composite structures. Meccanica, Springer Verlag, 2015, 50 (10), pp.2587 - 2620 [HAL] / [DOI]
2015Jérôme Michetti, Marie Georgelin-Gurgel, Jean-Philippe Mallet, Franck Diemer, Kader Boulanouar. Influence of CBCT parameters on the output of an automatic edge-detection-based endodontic segmentation. Dentomaxillofacial Radiology, British Institute of Radiology, 2015, 44 (8), [HAL] / [DOI]
2015M. Bergoglio, D. Mari, J. Chen, H. Si Hadj Mohand, Stéphane Colin, et al. Experimental and computational study of gas flow delivered by a rectangular microchannels leak. Measurement, Elsevier, 2015, 73, pp.551 - 562 [HAL] / [DOI]
2015Florian Bugarin, Adrien Bartoli, Didier Henrion, Jean-Bernard Lasserre, Jean-José Orteu, et al. Rank-constrained fundamental matrix estimation by polynomial global optimization versus the eight-point algorithm. Journal of Mathematical Imaging and Vision, Springer Verlag, 2015, 53 (1), pp.42-60 [HAL]
2015Andre Chateau Akue Asseko, Benoît Cosson, Fabrice Schmidt, Yannick Le Maoult, Eric Lafranche. Laser transmission welding of composites-Part A: Thermo-physical and optical characterization of materials. Infrared Physics and Technology, Elsevier, 2015, 72, p 293-299 [HAL] / [DOI]
2015Ion Hazyuk, Marc Budinger, Florian Sanchez, Jean-Charles Maré, Stéphane Colin. Scaling laws based metamodels for the selection of the cooling strategy of electromechanical actuators in the early design stages. Mechatronics, Elsevier, 2015, 29, pp.67 - 77 [HAL] / [DOI]
2015Benjamin Ostré, Christophe Bouvet, Clément Minot, Jacky Aboissière. Edge impact modeling on stiffened composite structures. Composite Structures, Elsevier, 2015, 126, pp.314-328 [HAL] / [DOI]
2015Etienne Gourc, Guilhem Michon, Sébastien Seguy, Alain Berlioz. Targeted Energy Transfer Under Harmonic Forcing With a Vibro-Impact Nonlinear Energy Sink: Analytical and Experimental Developments. Journal of Vibration and Acoustics / Journal of Vibration and Acoustics Transactions of the ASME, ASME International, 2015, 137 (3), [HAL] / [DOI]
2015Teddy Lisle, Christophe Bouvet, Marie-Laetitia Pastor, Thomas Rouault, Philippe Margueres. Damage of woven composite under tensile and shear stress using infrared thermography and micrographic cuts. Journal of Materials Science, Springer Verlag, 2015, 50 (18), pp.6154-6170 [HAL] / [DOI]
2015Guillaume Lélias, Eric Paroissien, Frederic Lachaud, Joseph Morlier, Sébastien Schwartz, et al. An extended semi-analytical formulation for fast and reliable mode I/II stress analysis of adhesively bonded joints. International Journal of Solids and Structures, Elsevier, 2015, vol 62, pp 18-38 [HAL] / [DOI]
2015M. Shah, Catherine Mabru, Farhad Rezai-Aria. Characterisation of the surface damage of X38CrMoV5 (AISI H11) tool steel at room temperature and 600 degrees C. Fatigue and Fracture of Engineering Materials and Structures, Wiley-Blackwell, 2015, 38 (6), p. 742-754 [HAL] / [DOI]
2015Valérie Pommier-Budinger, Olivier Cherrier. Baffle silencer with tunable resonators for adaptive control of variable tonal noise. Journal of Vibration and Control, SAGE Publications, 2015, 21 (9), pp.1801-1809 [HAL] / [DOI]
2015Teddy Lisle, Christophe Bouvet, Natthawat Hongkarnjanakul, Marie-Laetitia Pastor, Samuel Rivallant, et al. Measure of fracture toughness of compressive fiber failure in composite structures using infrared thermography. Composites Science and Technology, Elsevier, 2015, 112, pp.22-33 [HAL] / [DOI]
2015Fabien Hospital, Marc Budinger, Aurelien Reysset, Jean-Charles Maré. Preliminary design of aerospace linear actuator housings. Aircraft Engineering and Aerospace Technology, Emerald, 2015, 87 (3), pp.224 - 237 [HAL] / [DOI]
2015Gilles Dusserre. Modelling the hysteretic wale-wise stretching behaviour of technical plain knits. European Journal of Mechanics - A/Solids, Elsevier, 2015, 51, p 160-171 [HAL] / [DOI]
2015Peng Lv, Sebastien Prothin, Fazila Mohd Zawawi, Emmanuel Bénard, Joseph Morlier, et al. Performance improvement of small-scale rotors by passive blade twist control. Journal of Fluids and Structures, Elsevier, 2015, 55, pp.25-41 [HAL] / [DOI]
2015Valeria La Saponara, Anaïs Farrugia, Wahyu Lestari, Anastasia Muliana. Analysis of ultrasonic waveforms from smart sandwich composite structures under creep bending at elevated temperature. JOURNAL OF INTELLIGENT MATERIAL SYSTEMS AND STRUCTURES, 2015, 26 (7), pp.810-829 [HAL] / [DOI]
2015Christine Espinosa, Frederic Lachaud, Jérôme Limido, Jean-Luc Lacome, Antoine Bisson, et al. Coupling continuous damage and debris fragmentation for energy absorption prediction by cfrp structures during crushing. Computational Particle Mechanics, Springer Verlag, 2015, 2 (1), pp.1-17 [HAL] / [DOI]
2015Laurent Mezeix, Dominique Poquillon, Christophe Bouvet. Entangled cross-linked fibres for an application as core material for sandwich structures - Part I: Experimental investigation. Applied Composite Materials, Springer Verlag (Germany), 2015, 23 (1), pp.71-86 [HAL] / [DOI]
2015Elodie Cabrol, Christine Boher, V. Vidal, Farhad Rezai-Aria, Franck Touratier. Plastic strain of cobalt-based hardfacings under friction loading. Wear, Elsevier, 2015, 330 (SI), p 354-363 [HAL] / [DOI]
2015Mathieu Fogel, Patricia Parlevliet, Matthias Geistbeck, Philippe Olivier, Eric Dantras. Thermal, rheological and electrical analysis of MWCNTs/epoxy matrices. Composites Science and Technology, Elsevier, 2015, vol 110, pp 118-125 [HAL] / [DOI]
2015F. Szmytka, Mehdi Salem, Farhad Rezai-Aria, A. Oudin. Thermal fatigue analysis of automotive Diesel piston: Experimental procedure and numerical protocol. International Journal of Fatigue, Elsevier, 2015, 73, p.48-57 [HAL] / [DOI]
2015Andre Chateau Akue Asseko, Benoît Cosson, Mylene Deleglise, Fabrice Schmidt, Yannick Le Maoult, et al. Analytical and numerical modeling of light scattering in composite transmission laser welding process. International Journal of Material Forming, Springer Verlag, 2015, 8 (1), p 127-135 [HAL] / [DOI]
2015Feriel Samouda, Stéphane Colin, Christine Barrot, Lucien Baldas, Juergen Brandner. Micro molecular tagging velocimetry for analysis of gas flows in mini and micro systems. Microsystem Technologies, Springer Verlag, 2015, 21 (3), pp.527 - 537 [HAL] / [DOI]
2015Sabine Le Roux, Frédéric Deschaux-Beaume, Thierry Cutard, Philippe Lours. Quantitative assessment of the interfacial roughness in multi-layered materials using image analysis: Application to oxidation in ceramic-based materials. Journal of the European Ceramic Society, Elsevier, 2015, 35 (3), pp.1063-1079 [HAL] / [DOI]
2015Jérémie Vignes, Fabrice Schmidt, Gilles Dusserre, Jean Frederic Dalmasso. Numerical simulation of extruded clay paste compression. International Journal of Material Forming, Springer Verlag, 2015, 8 (1), p 111-118 [HAL] / [DOI]
2015Kuniaki Dohda, Christine Boher, Farhad Rezai-Aria, Numpon Mahayotsanun. Tribology in metal forming at elevated temperatures: review. FRICTION, 2015, 3 (1), p 1-27 [HAL] / [DOI]
2015M. Haddad, Redouane Zitoune, Florent Eyma, Bruno Castanié. Influence of Machining Process and Machining Induced Surface Roughness on Mechanical Properties of Continuous Fiber Composites. Experimental Mechanics, Society for Experimental Mechanics, 2015, 55 (3), p 519-528 [HAL] / [DOI]
2015B. Wang, L. D. Cot, Luc Adolphe, Sandrine Geoffroy, J. Morchain. Estimation of wind energy over roof of two perpendicular buildings. Energy and Buildings, Elsevier, 2015, 88, pp.57--67 [HAL] / [DOI]
2015Delphine Carponcin, Eric Dantras, Guilhem Michon, Jany Dandurand, Gwenaëlle Aridon, et al. New hybrid polymer nanocomposites for passive vibration damping by incorporation of carbon nanotubes and lead zirconate titanate particles. Journal of Non-Crystalline Solids, Elsevier, 2015, vol 409, pp 20-26 [HAL] / [DOI]
2015Florentin Berthet, Maxime Boulanghien, Gérard Bernhart, Yannick Soudais. Méthodes de détermination de la résistance en cisaillement à l’interface. Application au PA66 10%FC Revue des composites et des matériaux avancés, Lavoisier, 2015, 25 (3_4), p.295-309 [HAL] / [DOI]
2015Victor Munoz Cuartas, Marianne Perrin, Marie-Laetitia Pastor, Hélène Welemane, Arthur Cantarel, et al. Determination of the elastic properties in CFRP composites: comparison of different approaches based on tensile tests and ultrasonic characterization. Advances in Aircraft and Spacecraft Science, Techno-Press, 2015, vol 2 (n° 3), pp 249-260 [HAL] / [DOI]
2015T Bouzdine-Chameeva, André Ferrand, P. Valette Florence. Measurement and segmentation of sport fans using brand association networks: Application to Union of European Football Associations (UEFA) Champions League (UCL). . Sport Management Review, Elsevier, 2015, Vol 18, (n°3,), p 407-420 [HAL]
2015Hiroaki Matsumoto, Vincent Velay, Akihiko Chiba. Flow behavior and microstructure in Ti-6Al-4V alloy with an ultrafine-grained alpha-single phase microstructure during low-temperature-high-strain-rate superplasticity. Materials and Design, Elsevier, 2015, 66, p 611-617 [HAL] / [DOI]
2015Hakim Abdulhamid, Christophe Bouvet, Laurent Michel, Jacky Aboissière, Clément Minot. Influence of internally dropped-off plies on the impact damage of asymmetrically tapered laminated CFRP. Acta Materialia, Elsevier, 2015, vol 68, pp 110-120 [HAL] / [DOI]
2015Bernard Thibaut, Louis Denaud, Robert Collet, Rémy Marchal, Jacques Beauchêne, et al. Wood machining with a focus on French research in the last 50 years. Annals of Forest Science, Springer Verlag/EDP Sciences, 2015, 35 p [HAL] / [DOI]
2015Sami Daouk, François Louf, Olivier Dorival, Laurent Champaney, Sylvie Audebert. Uncertainties in structural dynamics: overview and comparative analysis of methods. Mechanics & Industry, EDP Sciences, 2015, 16 (4), pp.10 [HAL] / [DOI]
2015J. Harvent, Benjamin Coudrin, L. Brèthes, Jean-José Orteu, Michel Devy. Shape Measurement Using a New Multi-step Stereo-DIC Algorithm That Preserves Sharp Edges. Experimental Mechanics, Society for Experimental Mechanics, 2015, 55 (1), pp.167-176 [HAL] / [DOI]
2015Pablo Navarro, Florian Pascal, Julien Aubry, Steven Marguet, Jean-François Ferrero, et al. Semi-continuous approach for the study of impacts on woven composite laminates: Modeling interlaminar behavior with a specific interface element. International Journal of Impact Engineering, Elsevier, 2015, 75, pp.184 - 193 [HAL] / [DOI]
2015Jean-Charles Passieux, Jean-Noël Périé, Michel Salaün. A dual domain decomposition method for finite element digital image correlation. International Journal for Numerical Methods in Engineering, Wiley, 2015, 102 (10), pp.1670-1682 [HAL] / [DOI]
2015Pablo Navarro, Julien Aubry, Pascal Florian, Steven Marguet, Jean-François Ferrero, et al. Effects of the stacking sequence, material nature and addition of an adhesive film on the delamination resistance of woven composite laminates in mode I and II. Advanced composites letters, Woodhead Publishing Limited, 2015, 24 (1), pp.1-5 [HAL]
2015Olivier Dorival, Pablo Navarro, Steven Marguet, C Petiot, M Bermudez, et al. Experimental study of impact energy absorption by reinforced braided composite structures: Dynamic crushing tests. Composites Part B: Engineering, Elsevier, 2015, 78, pp.244-255 [HAL] / [DOI]
2014Etienne Copin, Thierry Sentenac, Yannick Le Maoult, Fabien Blas, Florence Ansart, et al. Feasibility of luminescent multilayer sol-gel thermal barrier coating manufacturing for future applications in through-thickness temperature gradient sensing. Surface and Coatings Technology, Elsevier, 2014, vol 260, pp 90-96 [HAL] / [DOI]
2014M. Abbas, Pascale Magaud, Y. Gao, Sandrine Geoffroy. Migration of finite sized particles in a laminar square channel flow from low to high Reynolds numbers. Physics of Fluids, American Institute of Physics, 2014, 26 (12), pp.123301 [HAL] / [DOI]
2014J. Chen, Lucien Baldas, Stéphane Colin. Numerical study of thermal creep flow between two ratchet surfaces. Vacuum, Elsevier, 2014, 109, pp.294 - 301 [HAL] / [DOI]
2014Marc Budinger, Jean-Charles Passieux, Christian Gogu, Amine Fraj. Scaling-law-based metamodels for the sizing of mechatronic systems. Mechatronics, Elsevier, 2014, 24 (7), pp.775-787 [HAL] / [DOI]
2014Joseph Morlier, Hanno Niemann, Amir Shahdin. Topology optimization for robust damage localization using aggregated FRFs statistical criteria. Journal of Applied Mechanics and Materials, 2014, 629, pp.513-518 [HAL] / [DOI]
2014Sébastien Seguy, Lionel Arnaud, Tamás Insperger. Chatter in interrupted turning with geometrical defects: an industrial case study. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2014, 75 (1-4), pp.45 - 56 [HAL] / [DOI]
2014Jean Heutte, Michel Galaup, Catherine Pons Lelardeux, Pierre Lagarrigue, Fabien Fenouillet. Etude des déterminants psychologiques de la persistance dans l'usage d'un jeu sérieux : évaluation de l'environnement optimal d'apprentissage avec Mecagenius®. Sciences et Technologies de l'Information et de la Communication pour l'Éducation et la Formation, ATIEF, 2014, 21, pp.1 [HAL]
2014Jean Heutte, Michel Galaup, Catherine Lelardeux, Pierre Lagarrigue, Fabien Fenouillet. Etude des déterminants psychologiques de la persistance dans l’usage d’un jeu sérieux : évaluation de l'environnement optimal d'apprentissage avec Mecagenius®. Sciences et Technologies de l'Information et de la Communication pour l'Éducation et la Formation, ATIEF, 2014, Evaluation dans les jeux sérieux, 21, pp.ISSN : 1764-7223, [HAL]
2014Rémi Gilblas, Thierry Sentenac, D. Hernandez, Yannick Le Maoult. Quantitative temperature field measurements on a non-gray multi-materials scene by thermoreflectometry. Infrared Physics and Technology, Elsevier, 2014, 66, p 70-77 [HAL] / [DOI]
2014Vincent Velay, H. Matsumoto, L. Sasaki, V. Vidal. Investigation of the mechanical behaviour of Ti-6Al-4V alloy under hot forming conditions: Experiment and modelling. Materials Science and Engineering Technology / Materialwissenschaft und Werkstofftechnik, Wiley-VCH Verlag, 2014, 45 (9), p 847-853 [HAL] / [DOI]
2014Lokman Bennani, Philippe Villedieu, Michel Salaün, Pierre Trontin. Numerical simulation and modeling of ice shedding: Process initiation. Computers and Structures, Elsevier, 2014, 142, pp.15-27 [HAL] / [DOI]
2014Natthawat Hongkarnjanakul, Samuel Rivallant, Christophe Bouvet, Arturo Miranda. Permanent indentation characterization for low-velocity impact modelling using three-point bending test. Journal of Composite Materials, SAGE Publications, 2014, 48 (20), pp.2441-2454 [HAL] / [DOI]
O. Le Fevre, P. Cassata, O. Cucciati, B. Garilli, O. Ilbert, et al. The VIMOS VLT Deep Survey final data release: a spectroscopic sample of 35016 galaxies and AGN out to z~6.7 selected with 17.5. [HAL]
2014Vlasios Leontidis, Jie Chen, Lucien Baldas, Stéphane Colin. Numerical design of a Knudsen pump with curved channels operating in the slip flow regime. Heat and Mass Transfer, Springer Verlag, 2014, 50 (8), pp.1065 - 1080 [HAL] / [DOI]
2014Jean-Charles Passieux, Pablo Navarro, Jean-Noël Périé, Steven Marguet, Jean-François Ferrero. A digital image correlation method for tracking planar motions of rigid spheres: application to medium velocity impacts. Experimental Mechanics, Society for Experimental Mechanics, 2014, 54 (8), pp.1453-1466 [HAL] / [DOI]
2014Laurent Robert, Gilles Dusserre. Assessment of Thermoset Cure-Induced Strains by Fiber Bragg Grating Sensor. Polymer Engineering and Science, Wiley-Blackwell, 2014, 54 (7), p 1585-1594 [HAL] / [DOI]
2014Simon Foucaud, Guilhem Michon, Yves Gourinat, Adrien Pelat, François Gautier. Artificial cochlea and acoustic black hole travelling waves observation: Model and experimental results. Journal of Sound and Vibration, Elsevier, 2014, vol 333 (n° 15), pp 3428-3439 [HAL] / [DOI]
2014Thomas Pottier, Guénaël Germain, Madalina Calamaz, Anne Morel, Dominique Coupard. Sub-millimeter measurement of finite strains at cutting tool tip vicinity. Experimental Mechanics, Society for Experimental Mechanics, 2014, 54 (6), pp.1031-1042 [HAL] / [DOI]
2014Victor Achard, Christophe Bouvet, Bruno Castanié, Clément Chirol. Discrete ply modelling of open hole tensile tests. Composite Structures, Elsevier, 2014, vol 113, pp 369-381 [HAL] / [DOI]
2014D'Elia Raffaele, Gérard Bernhart, Thierry Cutard, Gilles Peraudeau, Marianne Balat-Pichelin. Preliminary tests of silicon carbide based concretes for hybrid rocket nozzles in a solar furnace. Acta Astronautica, Elsevier, 2014, 99, pp.242-251 [HAL] / [DOI]
2014A. Ktari, M. Baccar, M. Shah, N. Haddar, H. F. Ayedi, et al. A crack propagation criterion based on Delta CTOD measured with 2D-digital image correlation technique. Fatigue and Fracture of Engineering Materials and Structures, Wiley-Blackwell, 2014, 37 (6), p 682-694 [HAL] / [DOI]
2014Luis Agnaldo Gomes Perini, Jean-Charles Passieux, Jean-Noël Périé. A multigrid PGD-based algorithm for volumetric displacement fields measurements. Strain, Wiley-Blackwell, 2014, 50 (4), pp.355-367 [HAL] / [DOI]
2014Benjamin Ostré, Christophe Bouvet, Frederic Lachaud, Clément Minot, Jacky Aboissière. Edge impact damage scenario on stiffened composite structure. Journal of Composite Materials, SAGE Publications, 2014, 42 p [HAL] / [DOI]
2014Samuel Rivallant, Christophe Bouvet, Elias Abi Abdallah, Bernhard Broll, Jean-Jacques Barrau. Experimental analysis of CFRP laminates subjected to Compression After Impact: the role of impact-induced cracks in failure. Composite Structures, Elsevier, 2014, vol 111, pp 147-157 [HAL] / [DOI]
2014Etienne Gourc, Guilhem Michon, Sébastien Seguy, Alain Berlioz. Experimental Investigation and Design Optimization of Targeted Energy Transfer Under Periodic Forcing. Journal of Vibration and Acoustics / Journal of Vibration and Acoustics Transactions of the ASME, ASME International, 2014, 136 (2), [HAL] / [DOI]
2014Lisa Pin, Vanessa Vidal, Fabien Blas, Florence Ansart, Sandrine Duluard, et al. Optimized sol–gel thermal barrier coatings for long-term cyclic oxidation life. Journal of the European Ceramic Society, Elsevier, 2014, vol 34 (n° 4), pp 961-974 [HAL] / [DOI]
2014Laurent Robert, Gilles Dusserre. Anisothermal thermosetting resin cure monitored by optical fiber refractometer. Polymer Engineering and Science, Wiley-Blackwell, 2014, 54 (3), p 626-635 [HAL] / [DOI]
2014Mohammed Cheikh, Alain Fermy. Prototype fretting device and some experimental results. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J‐JOURNAL OF ENGINEERING TRIBOLOGY, 2014, 228 (3), pp.266-275 [HAL]
2014Tchadja Kagnaya, Laurence Lambert, Myriam Lazard, Christine Boher, Thierry Cutard. Investigation and FEA-based simulation of tool wear geometry and metal oxide effect on cutting process variables. Simulation Modelling Practice and Theory, Elsevier, 2014, 42 (SI), p 84-97 [HAL] / [DOI]
2014Thomas Pottier, Hervé Louche, Serge Samper, Hugues Favreliěre, Franck Toussaint, et al. Proposition of a modal filtering method to enhance heat source computation within heterogeneous thermomechanical problems. International Journal of Engineering Science, Elsevier, 2014, 81, pp.163 - 176 [HAL] / [DOI]
2014Farid Medjedoub, Sabine Le Roux, Gilles Dour, Farhad Rezai-Aria. Effect of local stress on the heat-checking morphology in high temperature tool steels under thermal fatigue: Transition from multi-axiality to uniaxiality. Mechanics of Materials, Elsevier, 2014, 69 (1), p 159-172 [HAL] / [DOI]
2014Emeline Bessard, Olivier De Almeida, Gérard Bernhart. Unified isothermal and non-isothermal modelling of neat PEEK crystallization. JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY, 2014, 115 (2), p 1669-1678 [HAL] / [DOI]
2014Jérémy Crevel, Lascoup Bertrand. Etude du comportement de la protection foudre face à un impact mécanique. Revue des composites et des matériaux avancés, Lavoisier, 2014, 24 (2), [HAL] / [DOI]
2014Marie Poitrimolt, Mohammed Cheikh, Gérard Bernhart, Vincent Velay. Characterisation of the transverse mechanical properties of carbon/carbon composites by spherical indentation. Carbon, Elsevier, 2014, 66, p 234-245 [HAL] / [DOI]
2014Romuald Bertolaso, Mohammed Cheikh, Yoann Barranger, Jean-Christophe Dupré, Arnaud Germaneau, et al. Experimental and numerical study of the load distribution in a ball-screw system. Journal of Mechanical Science and Technology, 2014, 28 (4), p 1411-1420 [HAL] / [DOI]
2014Julien Aubry, Pablo Navarro, Steven Marguet, Jean-François Ferrero, Olivier Dorival, et al. Change of scale strategy for the microstructural modelling of polymeric rohacell foams. Computers, Materials & Continua, 2014, pp.21-47 [HAL] / [DOI]
2014Valérie Pommier-Budinger, Marc Budinger. Sizing optimization of piezoelectric smart structures with meta-modeling techniques for dynamic applications. International Journal of Applied Electromagnetics and Mechanics, IOS Press 2014, [HAL] / [DOI]
2014Fazila Mohd Zawawi, Peng Lv, Sebastien Prothin, Joseph Morlier, Jean-Marc Moschetta, et al. Study of a flexible UAV proprotor. International Journal of Engineering Systems Modelling and Simulation, InderScience, 2014, 6 (3/4), pp.149-161 [HAL]
2014Haris Ahmad Israr, Natthawat Hongkarnjanakul, Samuel Rivallant, Christophe Bouvet. Post-Impact Investigation of CFRP Laminated Plate. Jurnal Teknologi, 2014, 71 (2), pp.71-78 [HAL] / [DOI]
2014Pablo Navarro, Julien Aubry, Pascal Florian, Steven Marguet, Jean-François Ferrero, et al. Influence of the stacking sequence and crack velocity on fracture toughness of woven composite laminates in mode I. Engineering Fracture Mechanics, Elsevier, 2014, 131, pp.340-348. [HAL] / [DOI]
2014Sylvain Dubreuil, Marc Berveiller, Frank Petitjean, Michel Salaün. Construction of bootstrap confidence intervals on sensitivity indices computed by polynomial chaos expansion. Reliability Engineering and System Safety, Elsevier, 2014, vol 121, pp 263-275 [HAL] / [DOI]
2014Marc Budinger, J-F Rouchon, B Nogarede. Modélisation par méthode variationnelle d'un actionneur piézoélectrique à rotation de mode. Approche analytique et numérique European Journal of Electrical Engineering, Lavoisier, 2014, 7 (1-2), pp.223-251 [HAL] / [DOI]
2014Victor Pozzobon, Sylvain Salvador, Jean Jacques Bézian, Mouna El-Hafi, Yannick Le Maoult, et al. Radiative pyrolysis of wet wood under intermediate heat flux: Experiments and modelling. Fuel Processing Technology, Elsevier, 2014, 128, pp.319-330 [HAL] / [DOI]
2014Jean-Charles Passieux, Florian Bugarin, Christoph David, Jean-Noël Périé, Laurent Robert. Multiscale displacement field measurement using digital image correlation: Application to the identification of elastic properties. Experimental Mechanics, Society for Experimental Mechanics, 2014, 55 (1), pp.121-137 [HAL] / [DOI]
2014Tchadja Kagnaya, Christine Boher, Laurence Lambert, Myriam Lazard, Thierry Cutard. Microstructural analysis of wear micromechanisms of WC-6Co cutting tools during high speed dry machining. International Journal of Refractory Metals and Hard Materials, Elsevier, 2014, 42, p.151-162 [HAL] / [DOI]
2014Jean-Sébastien Brest, Vincent Keryvin, Patrice Longère, Yoshihiko Yokoyama. Insight into plasticity mechanisms in metallic glasses by means of a Brazilian test and numerical simulation. Journal of Alloys and Compounds, Elsevier, 2014, 586, pp.S236-S241 [HAL]
2014Elodie Cabrol, Christine Boher, Vanessa Vidal, Farhad Rezai-Aria, Fabienne Touratier. A wear damage assessment of high temperature forging tool. Advanced Materials Research, Trans Tech Publications, 2014, 966-967, p.103-110 [HAL] / [DOI]
2014Haris Ahmad Israr, Samuel Rivallant, Christophe Bouvet, Jean-Jacques Barrau. Finite element simulation of 0°/90° CFRP laminated plates subjected to crushing using a free-face-crushing concept. Composites Part A: Applied Science and Manufacturing, Elsevier, 2014, vol 62, pp 16-25 [HAL] / [DOI]
2014Laura Balea, Gilles Dusserre, Gérard Bernhart. Mechanical behaviour of plain-knit reinforced injected composites : effect of inlay yarns and fibre type. Composites Part B: Engineering, Elsevier, 2014, 56, p.20-29 [HAL] / [DOI]
2014Benoit Vieille, Victor Manuel Casado, Christophe Bouvet. Influence of matrix toughness and ductility on the compression-after-impact behavior of woven-ply thermoplastic- and thermosetting-composites: A comparative study. Composite Structures, Elsevier, 2014, vol 110, pp 207-218 [HAL] / [DOI]
2014Gilles Dusserre, Laura Balea, Gérard Bernhart. Elastic properties prediction of a knitted composite with inlaid yarns subjected to stretching: A coupled semi-analytical model. Composites Part A: Applied Science and Manufacturing, Elsevier, 2014, 64, pp.185 - 193 [HAL] / [DOI]
2013Victor Munoz, Marianne Perrin, Marie-Laetitia Pastor, Hélène Welemane, Arthur Cantarel, et al. Application of non destructive testing to the detection of aeronautical defects in composite structure. Nonconventional Technologies Review, 2013 [HAL]
2013Peng Lv, Fazila Mohd Zawawi, Emmanuel Bénard, Sebastien Prothin, Jean-Marc Moschetta, et al. An Application of Adaptive Blades on Convertible MAVs. International Journal of Micro Air Vehicles, 2013, 5 (4), pp.229-243 [HAL] / [DOI]
2013Ludovic Barrière, Steven Marguet, Bruno Castanié, Philippe Cresta, Jean-Charles Passieux. An adaptive model reduction strategy for post-buckling analysis of stiffened structures. Thin-Walled Structures, Elsevier, 2013, 73, pp.81-93 [HAL] / [DOI]
2013A. Nafi, Mohammed Cheikh, O. Mercier. Identification of mechanical properties of CuSil-steel brazed structures joints: a numerical approach. Journal of Adhesion Science and Technology, Taylor & Francis, 2013, 27 (24), pp.2705-2713 [HAL] / [DOI]
2013Jean-Charles Passieux, Julien Réthoré, Anthony Gravouil, Marie-Christine Baietto. Local/global non-intrusive crack propagation simulation using a multigrid X-FEM solver. Computational Mechanics, Springer Verlag, 2013, 52 (6), pp.1381-1393 [HAL] / [DOI]
2013Eric Vermesse, Catherine Mabru, Laurent Arurault. Surface integrity after pickling and anodization of Ti–6Al–4V titanium alloy. Applied Surface Science, Elsevier, 2013, vol 285 (Part B), pp 629-637 [HAL] / [DOI]
2013Amélie Kolopp, Samuel Rivallant, Christophe Bouvet. Experimental study of sandwich structures as armour against medium-velocity impacts. International Journal of Impact Engineering, Elsevier, 2013, vol 61, pp 24-35 [HAL] / [DOI]
2013Cédric Bellot, Pascal Lamesle, Denis Delagnes. XRD Synchrotron Study of Carbide Precipitation in Martensitic Steels During Tempering. Acta Metallurgica Sinica, Springer Verlag, 2013, 26 (5), pp.553-557 [HAL] / [DOI]
2013Fabien Amiot, Michel Bornert, Pascal Doumalin, Jean Christophe DuprÉ, Marina Fazzini, et al. Assessment of Digital Image Correlation Measurement Accuracy in the Ultimate Error Regime: Main Results of a Collaborative Benchmark. Strain, Wiley-Blackwell, 2013, 49 (6), pp.14 [HAL] / [DOI]
2012Satish Kandlikar, Stéphane Colin, Yoav Peles, Srinivas Garimella, R. Fabian Pease, et al. Heat Transfer in Microchannels—2012 Status and Research Needs. Journal of Heat Transfer, American Society of Mechanical Engineers, 2013, 135 (9), 091001 (18 p.) [HAL] / [DOI]
2013Cédric Bellot, Pascal Lamesle. Quantitative measurement of gamma prime precipitates in two industrial nickel-based superalloys using extraction and high resolution SEM imaging. Journal of Alloys and Compounds, Elsevier, 2013, 570, pp.100-103 [HAL] / [DOI]
2013Renaud Gantois, Arthur Cantarel, Benoit Cosson, Gilles Dusserre, Jean-Noël Felices, et al. BEM-based models to simulate the resin flow at macroscale and microscale in LCM processes. Polymer Composites, Wiley, 2013, 34 (8), pp.1235-1244 [HAL] / [DOI]
2013Florence Pettinari-Sturmel, B. Kedjar, Joël Douin, Christophe Gatel, Denis Delagnes, et al. TEM study of structural hardening in a new martensitic steel for aeronautic application. Materials Science and Engineering: A, Elsevier, 2013, 576, pp.290-297 [HAL] / [DOI]
2013Belkacem Hachemane, Redouane Zitoune, Boudjema Bezzazi, Christophe Bouvet. Sandwich composites impact and indentation behaviour study. Composites Part B: Engineering, Elsevier, 2013, vol 51, pp 1-10 [HAL] / [DOI]
2013Sabine Le Roux, Farhad Rezai-Aria. Topological and metric properties of microscopic crack patterns: application to thermal fatigue of high temperature tool steels. JOURNAL OF PHYSICS D‐APPLIED PHYSICS, 2013, 46 (29), [HAL] / [DOI]
2013Benoit Vieille, Victor Manuel Casado, Christophe Bouvet. About the impact behavior of woven-ply carbon fiber-reinforced thermoplastic- and thermosetting-composites: A comparative study. Composite Structures, Elsevier, 2013, vol 101, pp 9-21 [HAL] / [DOI]
2013Marc Budinger, Aurelien Reysset, Toufic El Halabi, Catalin Vasiliu, Jean-Charles Maré. Optimal preliminary design of electromechanical actuators. Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, SAGE Publications, 2013, 228 (9), pp.1598 - 1616 [HAL] / [DOI]
2013Laurent Tapie, Bernardin Mawussi, Walter Rubio, Benoît Furet. Machining of complex-shaped parts with guidance curves. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2013, 69 (5), pp.1499-1509 [HAL] / [DOI]
2013Sabine Le Roux, Farid Medjedoub, Gilles Dour, Farhad Rezai-Aria. Role of heat‐flux density and mechanical loading on the microscopic heat‐checking of high temperature tool steels under thermal fatigue experiments. International Journal of Fatigue, 2013, 51, pp.15-25 [HAL] / [DOI]
2013Thierry Sentenac, Rémi Gilblas. Noise effect on the interpolation equation for near infrared thermography. Metrologia, IOP Publishing, 2013, 50 (3), pp.208-218 [HAL] / [DOI]
2013Pablo Navarro, Serge Abrate, Julien Aubry, Steven Marguet, Jean-François Ferrero. Analytical modeling of indentation of composite sandwich beam. Composite Structures, Elsevier, 2013, 100, pp.79 - 88 [HAL] / [DOI]
2013Christian Garnier, Marie-Laetitia Pastor, Bernard Lorrain, Olivier Pantalé. Fatigue behaviour of impacted composite structures. Composite Structures, Elsevier, 2013, vol 100, pp 443-450 [HAL] / [DOI]
2013Jean-Max Redonnet, Sonia Djebali, Stéphane Segonds, Johanna Senatore, Walter Rubio. Study of the effective cutter radius for end milling of free-form surfaces using a torus milling cutter. Computer-Aided Design, Elsevier, 2013, 45 (6), pp.951-962 [HAL] / [DOI]
2013Etienne Gourc, Sébastien Seguy, Guilhem Michon, Alain Berlioz. Chatter Control in Turning Process with a Nonlinear Energy Sink. Advanced Materials Research, Trans Tech Publications, 2013, 698, pp.89-98 [HAL] / [DOI]
2013Alvine Njionhou, Florentin Berthet, Bruno Castanié. Effects of process parameters on the mechanical properties and morphology of stitched and non-stitched carbon/epoxy liquid resin-infused NCF laminate, out of autoclave and out of oven. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2013, 65 (9-12), pp.1289-1302 [HAL] / [DOI]
2013Elodie Cabrol, Cédric Bellot, Pascal Lamesle, Denis Delagnes, E. Povoden-Karadeniz. Experimental investigation and thermodynamic modeling of molybdenum and vanadium-containing carbide hardened iron-based alloys. Journal of Alloys and Compounds, Elsevier, 2013, 556, pp.203-209 [HAL] / [DOI]
2013Lisa Pin, Christopher Pilgrim, Jörg Feist, Yannick Le Maoult, Florence Ansart, et al. Characterisation of thermal barrier sensor coatings synthesised by sol–gel route. Sensors and Actuators A: Physical , Elsevier, 2013, vol 199, pp 289-296 [HAL] / [DOI]
2013Michel Chaussumier, Catherine Mabru, Majid Shahzad, Rémy Chieragatti, Farhad Rezai-Aria. A predictive fatigue life model for anodized 7050 aluminium alloy. International Journal of Fatigue, Elsevier, 2013, vol 48, pp 205-213 [HAL] / [DOI]
2013Irène Maillet, Laurent Michel, Germain Rico, Mathieu Fressinet, Yves Gourinat. A new test methodology based on structural resonance for mode I fatigue delamination growth in an unidirectional composite. Composite Structures, Elsevier, 2013, vol 97, pp 353-362 [HAL] / [DOI]
2013Pauline Lepesant, Christine Boher, Yves Berthier, Farhad Rezai-Aria. A phenomenological model of the third body particles circulation in a high temperature contact. Wear, Elsevier, 2013, 298-299, pp.66-79 [HAL] / [DOI]
2013Gilles Dusserre, F. Nazaret, Laurent Robert, Thierry Cutard. Applicability of image correlation techniques to characterise asymmetric refractory creep during bending tests. Journal of the European Ceramic Society, Elsevier, 2013, 33 (2), pp.221-231 [HAL] / [DOI]
2013Lisa Pin, Florence Ansart, Jean-Pierre Bonino, Yannick Le Maoult, Vanessa Vidal, et al. Reinforced sol-gel thermal barrier coatings and their cyclic oxidation life. Journal of the European Ceramic Society, Elsevier, 2013, vol 33, pp 269-276 [HAL] / [DOI]
2013Michel Mousseigne, Yann Landon, Sébastien Seguy, Gilles Dessein, Jean-Max Redonnet. Predicting the dynamic behaviour of torus milling tools when climb milling using the stability lobes theory. International Journal of Machine Tools and Manufacture, Elsevier, 2013, vol 65, pp 47-57 [HAL] / [DOI]
2013Haris Ahmad Israr, Samuel Rivallant, Jean-Jacques Barrau. Experimental investigation on mean crushing stress characterization of carbon-epoxy plies under compressive crushing mode. Composite Structures, Elsevier, 2013, vol 96, pp.357-364 [HAL] / [DOI]
2013Philippe Marguerès, Fodil Meraghni. Damage induced anisotropy and stiffness reduction evaluation in composite materials using ultrasonic wave transmission. Composites Part A: Applied Science and Manufacturing, Elsevier, 2013, 45, pp.134-144 [HAL] / [DOI]
2013Christian Gogu, Jean-Charles Passieux. Efficient surrogate construction by combining response surface methodology and reduced order modeling. Structural and Multidisciplinary Optimization, Springer Verlag (Germany), 2013, 47 (6), pp.821-837 [HAL] / [DOI]
2013Jacques Harvent, Benjamin Coudrin, Ludovic Brèthes, Jean-José Orteu, Michel Devy. Multi-view dense 3D modelling of untextured objects from a moving projector-cameras system. Machine Vision and Applications, Springer Verlag, 2013, 24 (8), pp.1645-1659 [HAL] / [DOI]
2013Karin Faria Pinho, Christine Boher, Cherlio Scandian. Effect of molybdenum and chromium contents on sliding wear of high-chromium white cast iron at high temperature. Lubrication Science, Wiley, 2013, First International Brazilian Conference on Tribology (TriboBR 2010), 25 (2), pp.153-162 [HAL] / [DOI]
2013Amélie Kolopp, Raquel Alvarado, Samuel Rivallant, Christophe Bouvet. Modeling impact on aluminium sandwich including velocity effects in honeycomb core. Journal of Sandwich Structures and Materials, SAGE Publications, 2013, 13 (6), pp.733-757 [HAL] / [DOI]
2013T. Benmbarek, Laurent Robert, H. Sammouda, Bertrand Charrier, Jean-José Orteu, et al. Effect of acetylation and additive on the tensile properties of wood fiber - HDPE composite. Journal of Reinforced Plastics and Composites, SAGE Publications, 2013, 32 (21), pp.1646-1655 [HAL] / [DOI]
2013Badis Haddag, Tchadja Kagnaya, Mohammed Nouari, Thierry Cutard. A new heat transfer analysis in machining based on two steps of 3D finite element modelling and experimental validation. Heat and Mass Transfer, Springer Verlag, 2013, 49 (1), pp.129--145 [HAL] / [DOI]
2013Marie-Cécile Robin, Denis Delagnes, Roland E. Logé, Pierre-Olivier Bouchard, Stéphanie Da Costa, et al. Thermo-mechanical fatigue behaviour of welded tubular parts made of ferritic stainless steel. International Journal of Fatigue, Elsevier, 2013, 54, pp.84 - 98 [HAL] / [DOI]
2013Emmanuel Mermoz, Julien Astoul, Marc Sartor, Jean-Marc Linares, Alain Bernard. A new methodology to optimize spiral bevel gear topography. CIRP Annals - Manufacturing Technology, Elsevier, 2013, 62, pp.119 - 122 [HAL] / [DOI]
2013Arnaud Duchosal, Frédéric Deschaux-Beaume, Philippe Lours, Sergio Haro, Gilles Fras. Analysis of weld-cracking and improvement of the weld-repair process of superplastic forming tools. Materials and Design, Elsevier, 2013, 46, pp.731-739 [HAL] / [DOI]
2013Xavier Giraud, Marc Sartor, Xavier Roboam, Bruno Sareni, Hubert Piquet, et al. Load allocation problem for optimal design of aircraft electrical power system . IJAEM: International Journal of Applied Electromagnetics and Mechanics, 2013 [HAL]
2013Pierre Selva, Olivier Cherrier, Valérie Pommier-Budinger, Frederic Lachaud, Joseph Morlier. Smart monitoring of aeronautical composites plates based on electromechanical impedance measurements and artificial neural networks. Engineering Structures, Elsevier, 2013, 56, pp.794-804 [HAL] / [DOI]
2013Olivier Cherrier, Pierre Selva, Valérie Pommier-Budinger, Frederic Lachaud, Joseph Morlier. Damage localization map using electromechanical impedance spectrums and inverse distance weighting interpolation: Experimental validation on thin composite structures. Structural Health Monitoring, SAGE Publications (UK and US), 2013, 12 (4), pp.311-324 [HAL] / [DOI]
2013Leonardo Sanches, Daniel Alazard, Guilhem Michon, Alain Berlioz. Robustness Analysis of Helicopter Ground Resonance with Parametric Uncertainties in Blade Properties. Journal of Guidance, Control, and Dynamics, American Institute of Aeronautics and Astronautics, 2013, 36 (1), pp.272-281 [HAL] / [DOI]
2013Elodie Péronnet, Marie-Laetitia Pastor, Richard Huillery, Olivier Dalverny, Sebastien Mistou, et al. Non destructive investigation of defects in composite structures by fullfield measurement methods. Key Engineering Materials, 2013, vol 550, pp 135-142 [HAL] / [DOI]
2013Anthony Delmas, Yannick Le Maoult, Jean-Marie Buchlin, Thierry Sentenac, Jean-José Orteu. Shape distortions induced by convective effect on hot object in visible, near infrared and infrared bands. Experiments in Fluids, Springer Verlag (Germany), 2013, 54 (4), pp.1452 [HAL] / [DOI]
2013Thomas Rouault, Christophe Bouvet, Vincent Nègre, Patrice Rauch. Reversible Rail Shear Apparatus Applied to the Study of Woven Laminate Shear Behavior. Experimental Mechanics, Society for Experimental Mechanics, 2013, 53 (8), pp.1437-1448 [HAL] / [DOI]
2013Michel Bornert, Fabrice Brémand, Pascal Doumalin, Jean-Christophe Dupré, Marina Fazzini, et al. Addendum to: Assessment of Digital Image Correlation Measurement Errors: Methodology and Results [Experimental Mechanics 49(3)]. Experimental Mechanics, Society for Experimental Mechanics, 2013, page 1 [HAL] / [DOI]
2013Cédric Pozzolini, Yves Renard, Michel Salaün. Vibro-impact of a plate on rigid obstacles: existence theorem, convergence of a scheme and numerical simulations. IMA Journal of Numerical Analysis, Oxford University Press (OUP), 2013, vol 33, pp 261 -294 [HAL] / [DOI]
2013Hakim Abdulhamid, Amélie Kolopp, Christophe Bouvet, Samuel Rivallant. Experimental and numerical study of AA5086-H111 aluminum plates subjected to impact. International Journal of Impact Engineering, Elsevier, 2013, 51, pp.1-12 [HAL] / [DOI]
2013Eric Paroissien, Fréderic Gaubert, A. Da Veiga, Frederic Lachaud. Elasto-plastic analysis of bonded joints with macro-elements. Journal of Adhesion Science and Technology, Taylor & Francis, 2013, vol 27, pp 1464-1498 [HAL] / [DOI]
2013John Le Dref, Florent Eyma, Gilles Dessein, Louis Etienne Denaud, Yann Landon. Comparative study of tools in drilling composites T700-M21 and T800-M21. Advanced Materials Research, Trans Tech Publications, 2013, vol 698, pp 59-68 [HAL] / [DOI]
2013Sabine Le Roux, Farid Medjedoub, Gilles Dour, Farhad Rezai-Aria. Image analysis of microscopic crack patterns applied to thermal fatigue heat-checking of high temperature tool steels. Micron, Elsevier, 2013, 44, pp.347-358 [HAL] / [DOI]
2013Natthawat Hongkarnjanakul, Christophe Bouvet, Samuel Rivallant. Validation of low velocity impact modelling on different stacking sequences of CFRP laminates and influence of fibre failure. Composite Structures, Elsevier, 2013, vol 106, pp 549-559 [HAL] / [DOI]
2013Teddy Lisle, Christophe Bouvet, Marie-Laetitia Pastor, Philippe Marguerès, Roberto Prieto Corral. Damage analysis and fracture toughness evaluation in a thin woven composite laminate under static tension using infrared thermography. Composites Part A: Applied Science and Manufacturing, Elsevier, 2013, vol 53, pp 75-87 [HAL] / [DOI]
2013Samuel Rivallant, Christophe Bouvet, Natthawat Hongkarnjanakul. Failure analysis of CFRP laminates subjected to Compression After Impact: FE simulation using discrete interface elements. Composites Part A: Applied Science and Manufacturing, Elsevier, 2013, vol 55, pp 83-93 [HAL] / [DOI]
2012Emmanuel Marin, Laurent Robert, Sébastien Triollet, Youcef Ouerdane. Liquid Resin Infusion process monitoring with superimposed Fibre Bragg Grating sensor. Polymer Testing, Elsevier, 2012, 31 (8), pp.1045-1052 [HAL] / [DOI]
2012N. Lebaal, S. Puissant, F. M. Schmidt, D. Schlaefli. An optimization method with experimental validation for the design of extrusion wire coating dies for a range of different materials and operating conditions. Polymer Engineering and Science, Wiley-Blackwell, 2012, 52 (12), pp.2675-2687 [HAL] / [DOI]
2012Thierry Sentenac, Rémi Gilblas, Daniel Hernandez, Yannick Le Maoult. Bi-color near infrared thermoreflectometry: A method for true temperature field measurement. Review of Scientific Instruments, American Institute of Physics, 2012, 83 (12), [HAL] / [DOI]
2012Ihab El Sawi, Philippe Olivier, Philippe Demont, Habiba Bougherara. Processing and electrical characterization of a unidirectional CFRP composite filled with double walled carbon nanotubes. Composites Science and Technology, Elsevier, 2012, vol 73, pp 19-26 [HAL] / [DOI]
2012Ihab El Sawi, Philippe Olivier, Philippe Demont, Habiba Bougherara. Investigation of the effect of double-walled carbon nanotubes on the curing reaction kinetics and shear flow of an epoxy resin. Journal of Applied Polymer Science, Wiley, 2012, vol 126, pp.358-366 [HAL] / [DOI]
2012Pablo Navarro, Steven Marguet, Jean-François Ferrero, Jean-Jacques Barrau, Sandrine Lemaire. Modeling of Impacts on Sandwich Structures. Mechanics of Advanced Materials and Structures, Taylor & Francis, 2012, 19 (7), pp.523 - 529 [HAL] / [DOI]
2012J. Liscouët, Jean-Charles Maré, Marc Budinger. An integrated methodology for the preliminary design of highly reliable electromechanical actuators: Search for architecture solutions. Aerospace Science and Technology, Elsevier, 2012, 22 (1), pp.9 - 18 [HAL] / [DOI]
2012Louis Adam, Christophe Bouvet, Bruno Castanié, Alain Daidié, Elodie Bonhomme. Discrete ply model of circular pull-through test of fasteners in laminates. Composite Structures, Elsevier, 2012, vol 94, pp 3082-3091 [HAL] / [DOI]
2012Vincent Velay, Thierry Cutard, N. Guegan. Thermal behaviour modelling of superplastic forming tools. Materials Science and Engineering Technology / Materialwissenschaft und Werkstofftechnik, Wiley-VCH Verlag, 2012, 43 (9, SI), pp.799-804 [HAL] / [DOI]
2012Aurélien Mazzoni, Gérard Bernhart, Thierry Cutard. Ceramic fibre reinforced refractory castables for very high temperature superplastic forming. Materials Science and Engineering Technology / Materialwissenschaft und Werkstofftechnik, Wiley-VCH Verlag, 2012, 43 (9, SI), pp.758-762 [HAL] / [DOI]
2012M. Cusick, F. Abu-Farha, Philippe Lours, Yannick Le Maoult, Gérard Bernhart, et al. Superplastic forming of AZ31 magnesium alloy with controlled microstructure. Materials Science and Engineering Technology / Materialwissenschaft und Werkstofftechnik, Wiley-VCH Verlag, 2012, 43 (9, SI), pp.810-816 [HAL] / [DOI]
2012Cyril Renault, Jérôme Roche, Mihaela Raluca Ciumag, Theodore Tzedakis, Stéphane Colin, et al. Design and optimization of electrochemical microreactors for continuous electrosynthesis. Journal of Applied Electrochemistry, Springer Verlag, 2012, vol 42, pp 667-677 [HAL] / [DOI]
2012Issam Tawk, Julien Aubry, Pablo Navarro, Jean-François Ferrero, Steven Marguet, et al. Study of impact on helicopter blade. Engineering Failure Analysis, Elsevier, 2012, 24, pp.38-45 [HAL] / [DOI]
2012Denis Delagnes, Florence Pettinari-Sturmel, M. H. Mathon, R. Danoix, F. Danoix, et al. Cementite-free martensitic steels: A new route to develop high strength/high toughness grades by modifying the conventional precipitation sequence during tempering. Acta Materialia, Elsevier, 2012, 60 (16), pp.5877-5888 [HAL] / [DOI]
2012Masood Shah, Catherine Mabru, Farhad Rezai-Aria, Inès Souki, Riffat Asim Pasha. An estimation of stress intensity factor in a clamped SE(T) specimen through numerical simulation and experimental verification: case of FCGR of AISI H11 tool steel. ACTA METALLURGICA SINICA‐ENGLISH LETTERS, 2012, 25 (4), pp.307-319 [HAL] / [DOI]
2012Miguel Charlotte, Lev Truskinovsky. Lattice dynamics from a continuum viewpoint. Journal of the Mechanics and Physics of Solids, Elsevier, 2012, 60 (8), pp.1508-1544 [HAL] / [DOI]
2012Jérémie Lasry, Yves Renard, Michel Salaün. Stress intensity factors computation for bending plates with extended finite element method. International Journal for Numerical Methods in Engineering, Wiley, 2012, vol 91, pp 909-928 [HAL] / [DOI]
2012Leonardo Sanches, Guilhem Michon, Alain Berlioz, Daniel Alazard. Parametrically excited helicopter ground resonance dynamics with high blade asymmetries. Journal of Sound and Vibration, Elsevier, 2012, vol 331, pp 3897-3913 [HAL] / [DOI]
2012Pablo Navarro, Julien Aubry, Steven Marguet, Jean-François Ferrero, Sandrine Lemaire, et al. Semi-continuous approach for the modeling of thin woven composite panels applied to oblique impacts on helicopter blades. Composites Part A: Applied Science and Manufacturing, Elsevier, 2012, 43 (6), pp.871 - 879 [HAL] / [DOI]
2012Pablo Navarro, Julien Aubry, Steven Marguet, Jean-François Ferrero, Sandrine Lemaire, et al. Experimental and numerical study of oblique impact on woven composite sandwich structure: Influence of the firing axis orientation. Composite Structures, Elsevier, 2012, 94 (6), pp.1967 - 1972 [HAL] / [DOI]
2012Marc Budinger, Jonathan Liscouët, Fabien Hospital, Jean-Charles Maré. Estimation models for the preliminary design of electromechanical actuators. Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, SAGE Publications, 2012, 226 (3), pp.243-259 [HAL] / [DOI]
2012Cyril Renault, Stéphane Colin, Stéphane Orieux, Patrick Cognet, Théo Tzedakis. Optimal design of multi-channel microreactor for uniform residence time distribution. Microsystem Technologies, Springer Verlag, 2012, 18 (2), pp.209 - 223 [HAL] / [DOI]
2012Mikael Perrut, Marie-Helene Mathon, Denis Delagnes. Small-angle neutron scattering of multiphase secondary hardening steels. Journal of Materials Science, Springer Verlag, 2012, 47 (4), pp.1920-1929 [HAL] / [DOI]
2012Laurent Robert, Vincent Velay, Nicolas Decultot, Souleymane Ramde. Identification of hardening parameters using finite element models and full-field measurements: some case studies. Journal of Strain Analysis for Engineering Design, SAGE Publications, 2012, 47 (1), pp.3-17 [HAL] / [DOI]
2012Yann Goueffon, Grégory Aldebert, Catherine Mabru, Laurent Arurault, Claire Tonon, et al. Flaking of black anodic films in space environment: Ageing and numerical simulation. Mechanics of Materials, Elsevier, 2012, 45, pp.72-82 [HAL] / [DOI]
2012Hugo Leclerc, Jean-Noël Périé, François Hild, Stéphane Roux. Digital volume correlation: what are the limits to the spatial resolution? Mechanics & Industry, EDP Sciences, 2012, 13, pp.361-371 [HAL] / [DOI]
2012Cédric Bellot, Denis Delagnes, Pascal Lamesle. Mécanismes de précipitation dans les aciers martensitiques au carbone : caractérisation par DRX synchrotron et simulation thermocinétique. Materiaux et Techniques, 2012, 100 (Hors-Série), p.117-118 [HAL]
2012Christophe Paris, Gérard Bernhart, Philippe Olivier, Olivier De Almeida. Influence de cycles de cuisson rapides sur le préimprégné aéronautique M21/T700 : suivi de polymérisation et propriétés mécaniques. Materiaux et Techniques, 2012, 100 (6-7), p.611-622 [HAL]
2012Cédric Bellot, Denis Delagnes, Pascal Lamesle. Developing cementite-free martensitic steels : a new route to improve the ultimate tensile strength-fracture toughness balance. Materiaux et Techniques, 2012, 100 (Hors-Série), p.76-78 [HAL]
2012Sabine Le Roux, Christine Boher, Luc Penazzi, C. Dessain, B. Tavernier. A methodology and new criteria to quantify the adhesive and abrasive wear damage on a die radius using white light profilometry. Tribology International, Elsevier, 2012, 52, pp.40-49 [HAL] / [DOI]
2012Thomas Vandellos, Mathieu Hautier, Nicolas Carrère, Cédric Huchette. Development of a new fracture test to identify the critical energy release rate: The Tensile Flexure test on Notched Specimen. Engineering Fracture Mechanics, Elsevier, 2012, 96, pp.641-655 [HAL] / [DOI]
2012Fazila Mohd Zawawi, Joseph Morlier, Gilles Grondin, Jean-Marc Moschetta. Design of Optimum Torsionally Flexible PropRotors for Tilt-Body MAVs. Applied Mechanics and Materials, Trans Tech Publications, 2012, AEROTECH IV, 225, pp.281-286 [HAL] / [DOI]
2012Majid Shahzad, Michel Chaussumier, Rémy Chieragatti, Catherine Mabru, Farhad Rezai-Aria. Effect of sealed anodic film on fatigue performance of 2214-T6 aluminium alloy. Surface and Coatings Technology, Elsevier, 2012, vol 206, pp.2733-2739 [HAL]
2012Christian Gogu, Youchun Qiu, Stéphane Segonds, Christian Bes. Optimization based algorithms for uncertainty propagation through functions with multidimensional output within evidence theory. Journal of Mechanical Design, American Society of Mechanical Engineers, 2012, 134 (10), p 914 [HAL] / [DOI]
2012Stéphane Colin. Gas microflows in the slip flow regime: A critical review on convective heat transfer. Journal of Heat Transfer, American Society of Mechanical Engineers, 2012, 134 (2), 020908 (13 p.) [HAL] / [DOI]
2012Alvine Njionhou, Florentin Berthet, Bruno Castanié, Christophe Bouvet. Relationships between LRI process parameters and impact and post-impact behaviour of stitched and unstitched NCF laminates. Applied Composite Materials, Springer Verlag (Germany), 2012, vol 19, pp 885-899 [HAL] / [DOI]
2012Thomas Vandellos, Mathieu Hautier, Nicolas Carrere, Cédric Huchette. Development of a new fracture test to identify the critical energy release rate: The Tensile Flexure test on Notched Specimen. Engieneering Fracture Mechanics, 2012, 96, pp.64-65 [HAL]
2012Louis Denaud, Laurent Bleron, Florent Eyma, Rémy Marchal. Wood peeling process monitoring: a comparison of signal processing methods to estimate veneer average lathe check frequency. European Journal of Wood and Wood Products, Springer Verlag, 2012, 70 (1-3), pp.253-261 [HAL]
2012Christine Boher, Sabine Le Roux, Luc Penazzi, C. Dessain. Experimental investigation of the tribological behavior and wear mechanisms of tool steel grades in hot stamping of a high-strength boron steel. Wear, Elsevier, 2012, 294, pp.286-295 [HAL] / [DOI]
2012Jean-Charles Passieux, Jean-Noël Périé. High resolution digital image correlation using proper generalized decomposition: PGD-DIC. International Journal for Numerical Methods in Engineering, Wiley, 2012, 92 (6), pp.531-550 [HAL] / [DOI]
2012Khalil Ben Slima, Luc Penazzi, Catherine Mabru, François Ronde-Oustau. Fatigue analysis-based numerical design of stamping tools made of cast iron. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2012, [HAL] / [DOI]
2012Christophe Bouvet, Samuel Rivallant, Jean-Jacques Barrau. Low velocity impact modeling in composite laminates capturing permanent indentation. Composites Science and Technology, Elsevier, 2012, 72 (16), pp.1977-1988 [HAL] / [DOI]
2012Pierre Rahmé, Christophe Bouvet, Samuel Rivallant, Valia Fascio, Guy Valembois. Experimental investigation of impact on composite laminates with protective layers. Composites Science and Technology, Elsevier, 2012, 72 (2), pp.182-189 [HAL] / [DOI]
2011Lisa Pin, Florence Ansart, Jean-Pierre Bonino, Yannick Le Maoult, Vanessa Vidal, et al. Processing, repairing and cyclic oxidation behaviour of sol-gel thermal barrier coatings. Surface and Coatings Technology, Elsevier, 2011, vol 206, pp 1609-1614 [HAL] / [DOI]
2011Thibault Gouache, Christopher Brunskill, Gregory Scott, Yves Gourinat, Pierre Coste, et al. Regolith simulant preparation methods for hardware testing. Planetary and Space Science, Elsevier, 2011, 58 (14-15), pp.1977-1984 [HAL] / [DOI]
2011F. Danoix, R. Danoix, J. Akre, A. Grellier, Denis Delagnes. Atom probe tomography investigation of assisted precipitation of secondary hardening carbides in a medium carbon martensitic steels. Journal of Microscopy, Wiley, 2011, 244 (3), pp.305-310 [HAL] / [DOI]
2011Vincent Cazajus, Sébastien Seguy, Hélène Welemane, Moussa Karama. Residual stresses in a ceramic-metal composite. Applied Mechanics and Materials, Trans Tech Publications, 2011, vol 146, pp 185-196 [HAL] / [DOI]
2011Etienne Gourc, Sébastien Seguy, Lionel Arnaud. Chatter milling modeling of active magnetic bearing spindle in high-speed domain. International Journal of Machine Tools and Manufacture, Elsevier, 2011, vol 51, pp 928-936 [HAL] / [DOI]
2011Gilles Dusserre, Gérard Bernhart, F. M. Schmidt, Gilles Dour. Evaluation of viscous and elastic parameters of a borosilicate glass above transition temperature using optical instrumented squeeze tests. Journal of Non-Newtonian Fluid Mechanics, Elsevier, 2011, 166 (21-22), pp.1229-1238 [HAL] / [DOI]
2011Solene Tadier, Nadine Le Bolay, Sophie Girod Fullana, Sophie Cazalbou, Cédric Charvillat, et al. Co-grinding significance for calcium carbonate-calcium phosphate mixed cement. Part II: effect on cement properties Journal of Biomedical Materials Research Part B: Applied Biomaterials, Wiley, 2011, 99B (2), pp.302-312 [HAL] / [DOI]
2011Cédric Pozzolini, Michel Salaün. SOME ENERGY CONSERVATIVE SCHEMES FOR VIBRO-IMPACTS OF A BEAM ON RIGID OBSTACLES. ESAIM: Mathematical Modelling and Numerical Analysis, EDP Sciences, 2011, pp.1163-1192 [HAL]
2011Benjamin Coudrin, Michel Devy, Jean-José Orteu, Ludovic Brèthes. An innovative hand-held vision-based digitizing system for 3D modelling. Optics and Lasers in Engineering, Elsevier, 2011, 49 (9-10), pp.1168-1176 [HAL] / [DOI]
2011Leonardo Sanches, Guilhem Michon, Alain Berlioz, Daniel Alazard. Instability zones for isotropic and anisotropic multibladed rotor configurations. Mechanism and Machine Theory, Elsevier, 2011, 46 (8), pp.1054-1065 [HAL] / [DOI]
2011Pierre Kerfriden, Jean-Charles Passieux, Stephane Pierre-Alain Bordas. Local/global model order reduction strategy for the simulation of quasi-brittle fracture. International Journal for Numerical Methods in Engineering, Wiley, 2011, 89 (2), pp.154-179 [HAL] / [DOI]
2011Sawsane Nakouzi, Johann Pancrace, Fabrice Schmidt, Yannick Le Maoult, Florentin Berthet. Simulations of an Infrared Composite Curing Process. Advanced Engineering Materials, Wiley-VCH Verlag, 2011, 13 (7, SI), pp.604-608 [HAL] / [DOI]
2011Patrick Gilles, Johanna Senatore, Stéphane Segonds, Frederic Monies, Walter Rubio. Determination of angular fields outside low and high collisions to mill free-form surfaces on 5-axis CNC Machines. International Journal of Production Research, Taylor & Francis, 2011, [HAL] / [DOI]
2011Madjid Haddad, Yves Gourinat, M. Charlotte. Equivalence Theory Applied to Anisotropic Thin Plates. Engineering, 2011, 3 (7), pp.669-679 [HAL] / [DOI]
2011Adrien Perret, Sebastien Mistou, Louis Etienne Denaud, Thierry Molle, Claudia Veyrac, et al. Numerical modelling of a composite fuselage manufactured by liquid resin infusion. Applied Mechanics and Materials, Trans Tech Publications, 2011, vol 62, pp.49-56 [HAL] / [DOI]
2011Rizwan Shad, Guilhem Michon, Alain Berlioz. Modeling and analysis of nonlinear rotordynamics due to higher order deformations in bending. Applied Mathematical Modelling, Elsevier, 2011, 35 (5), pp.2145-2159 [HAL] / [DOI]
2011Jean-José Orteu, Florian Bugarin, J. Harvent, Laurent Robert, Vincent Velay. Multiple-Camera Instrumentation of a Single Point Incremental Forming Process Pilot for Shape and 3D Displacement Measurements: Methodology and Results. Experimental Mechanics, Society for Experimental Mechanics, 2011, 51 (4), pp.625-639 [HAL] / [DOI]
2011Benoit Cosson, Fabrice Schmidt, Yannick Le Maoult, Maxime Bordival. Infrared heating stage simulation of semi-transparent media (PET) using ray tracing method. International Journal of Material Forming, Springer Verlag, 2011, 4 (1), pp.1-10 [HAL] / [DOI]
2011Jonathan Liscouët, Marc Budinger, Stéphane Orieux, Jean-Charles Maré. Modelling approach for the Simulation-Based Preliminary Design of Power Transmissions. Mechanism and Machine Theory, Elsevier, 2011, 46 (3), pp 276-289 [HAL] / [DOI]
2011Zhang Zhanping, Denis Delagnes, Gérard Bernhart. Cyclic behaviour and plastic strain memory effect of 55NiCrMoV7 steel under low cycle fatigue. Rare Metals, Springer Verlag, 2011, 30 (1, SI), pp.443-446 [HAL] / [DOI]
2011Abderrahim Michrafy, Harona Diarra, John A. Dodds, M. Michrafy, Luc Penazzi. Analysis of strain stress state in roller compaction process. Powder Technology, Elsevier, 2011, 208 (2, SI), pp.417-422 [HAL] / [DOI]
2011Matthieu Bizeul, Christophe Bouvet, Jean-Jacques Barrau, Rémy Cuenca. Fatigue crack growth in thin notched woven glass composites under tensile loading. Part I: experimental Composites Science and Technology, Elsevier, 2011, 71 (3), pp.289-296 [HAL] / [DOI]
2011Dimitri Bettebghor, Nathalie Bartoli, Stéphane Grihon, Joseph Morlier, Manuel Samuelides. Surrogate modeling approximation using a mixture of experts based on EM joint estimation. Structural and Multidisciplinary Optimization, 2011, 43 (2), pp.243-259 [HAL] / [DOI]
2011Gilles Dusserre, Eric Jourdain, Gérard Bernhart. Effect of deformation on knitted glass preform in-plane permeability. Polymer Composites, Wiley, 2011, 32 (1), p.18-28 [HAL]
2011Fabrice Schmidt, Nicolas Pirc, Marcel Mongeau, Francisco Chinesta. Efficient Mold Cooling Optimization by Using Model Reduction. International Journal of Material Forming, Springer Verlag, 2011, 4 (1), pp.73-82 [HAL] / [DOI]
2011Cédric Pozzolini, Michel Salaün. Some energy conservative schemes for vibro-impacts of a beam on rigid obstacles. ESAIM: Mathematical Modelling and Numerical Analysis, EDP Sciences, 2011, vol 45, pp 1163-1192 [HAL] / [DOI]
2011Sébastien Triollet, Laurent Robert, Emmanuel Marin, Youcef Ouerdane. Discriminated measures of strain and temperature in metallic specimen with embedded superimposed long and short fibre Bragg Gratings. Measurement Science and Technology, IOP Publishing, 2011, 22 (1), pp.015202 [HAL] / [DOI]
2011O. Bourrion, C. Bernard, D. Bondoux, J.L. Bouly, J. Bouvier, et al. Design and construction of a Cherenkov imager for charge measurement of nuclear cosmic rays. Journal of Instrumentation, IOP Publishing, 2011, 6, pp.P06004 [HAL] / [DOI]
2011Amir Shahdin, Joseph Morlier, Laurent Mezeix, Christophe Bouvet, Yves Gourinat. Evaluation of the impact resistance of various composite sandwich beams by vibration tests. Shock and Vibration, IOS Press, 2011, 18 (6), pp.789-805 [HAL] / [DOI]
2011Julien Sniezewski, Philippe Lours, Yannick Le Maoult. Buckling and spalling failure of alumina grown by oxidation on ODS FeCrAl alloys. Materials at High Temperatures, Taylor and Francis, 2011, 28 (1), pp.17-20 [HAL] / [DOI]
2011Majid Shahzad, Michel Chaussumier, Rémy Chieragatti, Catherine Mabru, Farhad Rezai-Aria. Surface characterization and influence of anodizing process on fatigue life of Al 7050 alloy. Materials and Design, Elsevier, 2011, 32 (6), pp.3328-3335 [HAL] / [DOI]
2011Mouldi Ben Azzouna, Jean-Noël Périé, Jean-Mathieu Guimard, François Hild, Stéphane Roux. On the Identification and Validation of an Anisotropic Damage Model Using Full-field Measurements. International Journal of Damage Mechanics, SAGE Publications, 2011, 20, pp.1130-1150 [HAL] / [DOI]
2011Jamel Madiouli, Jalila Sghaier, Jean-José Orteu, Laurent Robert, Didier Lecomte, et al. Non-contact Measurement of the Shrinkage and Calculation of Porosity During the Drying of Banana. Drying Technology, Taylor & Francis, 2011, 29 (12), pp.358-1364 [HAL] / [DOI]
2011Renaud Gantois, Arthur Cantarel, Gilles Dusserre, Jean Noël Felices, Fabrice Schmidt. Mold filling simulation of resin transfer molding combining BEM and level set method. Applied Mechanics and Materials, Trans Tech Publications, 2011, 62, p.57-65 [HAL] / [DOI]
2011Talel Ben Mbarek, Laurent Robert, Francoise Hugot, Jean-José Orteu. Mechanical behavior of wood-plastic composites investigated by 3D digital image correlation. Journal of Composite Materials, SAGE Publications, 2011, 45 (26), pp.2751-2764 [HAL] / [DOI]
2011Amir Shahdin, Joseph Morlier, Hanno Niemann, Yves Gourinat. Correlating low energy impact damage with changes in modal parameters: diagnosis tools and FE validation. Structural Health Monitoring, SAGE Publications (UK and US), 2011, 10 (2), pp.199-217 [HAL] / [DOI]
2011Tchadja Kagnaya, Myriam Lazard, Laurence Lambert, Christine Boher, Thierry Cutard. Temperature evolution in a WC-6% Co cutting tool during turning machining : experiment and finite element simulations. WSEAS Transactions on Heat and Mass Transfer, World Scientific and Engineering Academy and Society (WSEAS), 2011, 6 (3), pp.71-80 [HAL]
2011Hugo Leclerc, Jean-Noël Périé, Stéphane Roux, François Hild. Voxel-Scale Digital Volume Correlation. Experimental Mechanics, Society for Experimental Mechanics, 2011, 51 (4), pp.479-490 [HAL] / [DOI]
2011T. Zhu, M. A. Sutton, N. Li, Jean-José Orteu, Nicolas Cornille, et al. Quantitative Stereovision in a Scanning Electron Microscope. Experimental Mechanics, Society for Experimental Mechanics, 2011, 51 (1), pp.97-109 [HAL] / [DOI]
2011Jérôme Limido, Christine Espinosa, Michel Salaün, Catherine Mabru, Rémy Chieragatti, et al. Metal cutting modelling SPH approach. International Journal of Machining and Machinability of Materials, Inderscience, 2011, 9 (3-4), pp.177-196 [HAL] / [DOI]
2011Lionel Arnaud, Oscar Gonzalo, Sébastien Seguy, Haritz Jauregi, Grégoire Peigné. Simulation of low rigidity part machining applied to thin-walled structures. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2011, vol 54, pp 479-488 [HAL] / [DOI]
2011Francisco Javier Campa, Luis Norberto Lopez de Lacalle, Gorka Urbicain, Aitzol Lamikiz, Sébastien Seguy, et al. Critical thickness and dynamic stiffness for chatter avoidance in thin floors milling. Advanced Materials Research, Trans Tech Publications, 2011, vol 188, pp 116-121 [HAL] / [DOI]
2011Etienne Gourc, Sébastien Seguy, Gilles Dessein. Dynamical modeling of spindle with active magnetic bearing for milling process. Advanced Materials Research, Trans Tech Publications, 2011, vol 423, pp 200-209 [HAL] / [DOI]
2011Christian Garnier, Marie-Laetitia Pastor, Florent Eyma, Bernard Lorrain. The detection of aeronautical defects in-situ on composite structures using Non Destructive Testing. Composite Structures, Elsevier, 2011, vol 93, pp 1328-1336 [HAL] / [DOI]
2011Jeong Sik Kim, Luciana Arronche, Anaïs Farrugia, Anastasia Muliana, Valeria La Saponara. Multi-scale modeling of time-dependent response of smart sandwich constructions. Composite Structures, Elsevier, 2011, 93 (9), p.2196-2207 [HAL] / [DOI]
2011Matthieu Bizeul, Christophe Bouvet, Jean-Jacques Barrau, Rémy Cuenca. Fatigue crack growth in thin notched woven glass composites under tensile loading. Part II: modelling Composites Science and Technology, Elsevier, 2011, 71 (3), pp.297-305 [HAL] / [DOI]
2011Matthieu Bizeul, Christophe Bouvet, Jean-Jacques Barrau, Rémy Cuenca. Fatigue crack growth in thin notched woven glass composites under tensile loading. Part II: modelling Composites Science and Technology, Elsevier, 2011, 71 (3), pp.297-305 [HAL] / [DOI]
2010Lajos Szalmas, Jeerasak Pitakarnnop, Sandrine Geoffroy, Stéphane Colin, Dimitris Valougeorgis. Comparative study between computational and experimental results for binary rarefied gas flows through long microchannels. Microfluidics and Nanofluidics, Springer Verlag, 2010, 9 (6), pp.1103 - 1114 [HAL] / [DOI]
2010Yann Goueffon, Catherine Mabru, Michel Labarrère, Laurent Arurault, Claire Tonon, et al. Investigations into the coefficient of thermal expansion of porous films prepared on AA7175 T7351 by anodizing in sulphuric acid electrolyte. Surface and Coatings Technology, Elsevier, 2010, 205 (7), pp.2643-2648 [HAL] / [DOI]
2010Walid Trabelsi, Laurent Michel, Renaud Othomene. Effects of stitching on delamination of satin weave carbon-epoxy laminates under mode I, mode II and mixed-mode I/II loadings. Applied Composite Materials, Springer Verlag (Germany), 2010, 17 (6), pp.575-595 [HAL] / [DOI]
2010Julien Sniezewski, Yannick Le Maoult, Philippe Lours, Lisa Pin, Vincent Menvie Bekale, et al. Sol–gel thermal barrier coatings: Optimization of the manufacturing route and durability under cyclic oxidation. Surface and Coatings Technology, Elsevier, 2010, vol 205 (n° 5), pp 1256-1261 [HAL] / [DOI]
2010Muhammad Ilyas, Christine Espinosa, Frederic Lachaud, Laurent Michel, Michel Salaün. Modelling aeronautical composite laminates behaviour under impact using a saturation damage and delamination continuous material model. Key Engineering Materials, Trans Tech Publications, 2010, 452-453 (2011), pp.369-372 [HAL] / [DOI]
2010Marie-Laetitia Pastor, Christian Garnier, Christophe Pescay. Comparison of two non destructive tests in carbon/epoxy composites. Journal of Materials Science and Engineering, 2010, vol 4 [HAL]
2010Fabrice Schmidt, Nicolas Pirc, Marcel Mongeau, Francisco Chinesta. Efficient mold Danscooling optimization by using model reduction. International Journal of Material Forming, Springer Verlag, 2010, pp 1-10 [HAL] / [DOI]
2010Sébastien Seguy, Tamás Insperger, Lionel Arnaud, Gilles Dessein, Grégoire Peigné. On the stability of high-speed milling with spindle speed variation. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2010, vol 48, pp 883-895 [HAL] / [DOI]
2010Bartosz PaŁubicki, Rémy Marchal, Jean-Claude Butaud, Louis Denaud, Laurent Bleron, et al. A Method of Lathe Checks Measurement; SMOF device and its software. European Journal of Wood and Wood Products, 2010, 68 (2), pp.151-159 [HAL] / [DOI]
2010Sébastien Seguy, Gilles Dessein, Lionel Arnaud, Tamás Insperger. Control of Chatter by Spindle Speed Variation in High-Speed Milling. Advanced Materials Research, Trans Tech Publications, 2010, 112, pp.179 - 186 [HAL] / [DOI]
2010Yann Goueffon, Laurent Arurault, Sandra Fontorbes, Catherine Mabru, Claire Tonon, et al. Chemical characteristics, mechanical and thermo-optical properties of black anodic films prepared on 7175 aluminium alloy for space applications. Materials Chemistry and Physics, Elsevier, 2010, 120 (2-3), pp.636-642 [HAL] / [DOI]
2010R. Gantois, Arthur Cantarel, Gilles Dusserre, Jean-Noël Felices, F. Schmidt. Numerical simulation of resin transfer molding using BEM and level set method. International Journal of Material Forming, Springer Verlag, 2010, 3 (1), pp.635-638 [HAL] / [DOI]
2010Sawsane Nakouzi, J. Pancrace, F. M. Schmidt, Yannick Le Maoult, Florentin Berthet. Curing simulation of composites coupled with infrared heating. International Journal of Material Forming, Springer Verlag, 2010, 3 (1), pp.587-590 [HAL] / [DOI]
2010Majid Shahzad, Michel Chaussumier, Rémy Chieragatti, Catherine Mabru, Farhad Rezaï-Aria. Influence of anodizing process on fatigue life of a machined aluminium alloy. Procedia Engineering, Elsevier, 2010, 2 (1), pp.1015-1024 [HAL] / [DOI]
2010Hanno Niemann, Joseph Morlier, Amir Shahdin, Yves Gourinat. Damage localization using experimental modal parameters and topology optimization. Mechanical Systems and Signal Processing, Elsevier, 2010, 24 (3), pp.636-652 [HAL] / [DOI]
2010Ambrosius Weiss, Walid Trabelsi, Laurent Michel, Jean-Jacques Barrau, Stephane Mahdi. Influence of ply-drop location on the fatigue behaviour of tapered composites laminates. Procedia Engineering, Elsevier, 2010, 2 (1), pp.1105-1114 [HAL] / [DOI]
2010Nadhir Lebaal, Stephan Puissant, Fabrice Schmidt. Application of a response surface method to the optimal design of the wall temperature profiles in extrusion die. International Journal of Material Forming, Springer Verlag, 2010, 3 (1), pp.47-58 [HAL] / [DOI]
2010Amir Shahdin, Joseph Morlier, Yves Gourinat. Damage monitoring in sandwich beams by modal parameter shifts: a comparative study of burst random and sine dwell vibration testing. Journal of Sound and Vibration, Elsevier, 2010, 3 (5), pp.566-584 [HAL] / [DOI]
2010Xavier Pessoles, Yann Landon, Walter Rubio. Kinematic modelling of a 3-axis NC machine tool in linear and circular interpolation. International Journal of Advanced Manufacturing Technology, Springer Verlag, 2010, 47 (5-8), pp.639-655 [HAL] / [DOI]
2010Yann Goueffon, Catherine Mabru, Michel Labarrère, Laurent Arurault, Claire Tonon, et al. Mechanical behaviour of black anodic films on 7175 aluminium alloy for space applications. Metal Finishing, Elsevier, 2010, 108 (2), pp.22-27 [HAL] / [DOI]
2010Yves Gourinat, Uwe Apel, Franck Delbart. The aerocrew mission: training space session at Ny Aalesund Arctic base. Acta Astronautica, Elsevier, 2010, 66 (1-2), pp.74-77 [HAL] / [DOI]
2010Anwar Hamasaiid, Gilles Dour, T. Loulou, M.S. Dargusch. A predictive model for the evolution of the thermal conductance at the casting–die interfaces in high pressure die casting. International Journal of Thermal Sciences, Elsevier, 2010, 49 (2), pp.365 - 372 [HAL] / [DOI]
2010Issam Tawk, Pablo Navarro, Jean-François Ferrero, Jean-Jacques Barrau, Elie Abdullah. Composite delamination modelling using a multi-layered solid element. Composites Science and Technology, Elsevier, 2010, 70 (2), pp.207 - 214 [HAL] / [DOI]
2010Christophe Paris, Philippe Olivier, Gérard Bernhart. Modelling of the thermokinetic behaviour and the phases transitions of a carbon/polymeric composite submitted to high heating rate ramps. International Journal of Material Forming, Springer Verlag, 2010, 3 (Suppl 1), p.639-642 [HAL]
2010Majid Shahzad, Michel Chaussumier, Rémy Chieragatti, Catherine Mabru, Farhad Rezai-Aria. Influence of surface treatments on fatigue life of Al 7010 alloy. Journal of Materials Processing Technology, Elsevier, 2010, 210 (13), pp.1821-1826 [HAL] / [DOI]
2010A. Noeppel, A.I. Ciobanas, X.D. Wang, K. Zaïdat, Nathalie Mangelinck-Noël, et al. Influence of forced/natural convection on segregation during the directional solidification of Al-based binary alloys. Metallurgical and Materials Transactions B, Springer Verlag, 2010, 41 (1), pp.193-208 [HAL]
2010Florentin Berthet. Comparaison des cinétiques de réaction de la résine RTM6 à l'aide des diagrammes TTT. Revue des composites et des matériaux avancés, Lavoisier, 2010, 20 (1), p.25-40 [HAL]
2010Fabien Nazaret, Thierry Cutard, Olivier Barrau. Sizing of refractory castable gas-burner using thermomechanical simulations. Advances in Science and Technology, 2010, 70, p.173-178 [HAL]
2010Thierry Cutard, Nicolas Donval, Aurélien Mazzoni, Claire Michel, Fabien Nazaret. Thermomechanical characterization of monolithic refractory castables. Advances in Science and Technology, 2010, 70, p.37-46 [HAL] / [DOI]
2010Stéphane Segonds, Christian Gogu, Youchun Qiu, Christian Bes, A. Mauffrey. Design optimization under evidence based uncertainty with application to an engine connecting rod. International Journal of Design and Innovation Research, 2010, 5 (3), p 77-91 [HAL]
2010E. De Bilbao, Eric Blond, Christine Michel, N. Schmitt, Thierry Cutard, et al. A new method to determine Young's modulus of refractory. Interceram, 2010, 59 (1), pp.34-38 [HAL]
2010Alvine Njionhou Kepnang, Florentin Berthet, Bruno Castanié. Optimisation de la résistance au cisaillement interlaminaire (RCIL) des matériaux composites fabriqués par LRI en fonction des paramètres de fabrication. Materiaux et Techniques, 2010, 98 (2), p.151-163 [HAL]
2010Lisa Pin, Florence Ansart, Justine Fenech, Philippe Lours, Jean Pierre Bonino, et al. Advances in the field of new smart thermal barrier coatings. Advances in Science and Technology, 2010, 66, p.136-141 [HAL]
2010Pierre Selva, Joseph Morlier, Yves Gourinat. Toward a three-dimensional finite-element model of the human inner ear angular accelerometers sensors. International Journal for Computational Vision and Biomechanics (IJCV & B), 2010, 3 (2), pp.149-156 [HAL]
2010Joseph Morlier, Guilhem Michon. Virtual vibration measurement using KLT motion tracking algorithm. Journal of Dynamic Systems, Measurement, and Control, American Society of Mechanical Engineers, 2010, 132 (1), pp.011003-011011 [HAL] / [DOI]
2010R. Gantois, Arthur Cantarel, Jean-Noël Felices, N. Pirc, F. Schmidt. BEM Simulation Of 3D Updated Resin Front For LCM Processes. Key Engineering Materials, Trans Tech Publications, 2010, 446, pp.131-136 [HAL] / [DOI]
2010Matthieu Bizeul, Christophe Bouvet, Jean-Jacques Barrau, Rémy Cuenca. Influence of woven ply degradation on fatigue crack growth in thin notched composites under tensile loading. International Journal of Fatigue, Elsevier, 2010, 32 (1), pp.60-65 [HAL] / [DOI]
2010Matthieu Bizeul, Christophe Bouvet, Jean-Jacques Barrau, Rémy Cuenca. Influence of woven ply degradation on fatigue crack growth in thin notched composites under tensile loading. International Journal of Fatigue, Elsevier, 2010, 32 (1), pp.60-65 [HAL] / [DOI]
2010Nadhir Lebaal, Fabrice Schmidt, Stephan Puissant. Optimisation of extrusion flat die design and die wall temperature distribution, using Kriging and response surface method. International Journal of Materials and Product Technology, Inderscience, 2010, 38 (2-3), pp.307-322 [HAL] / [DOI]
2010Jérémie Lasry, Julien Pommier, Yves Renard, Michel Salaün. Extended finite element methods for thin cracked plates with Kirchhoff-Love theory. International Journal for Numerical Methods in Engineering, Wiley, 2010, 84 (9), pp.1115-1138 [HAL] / [DOI]
2009E. Abdullah, I. Tawk, J.-F. Ferrero, J.-J. Barrau. Mode I Delamination Modelling in a Composite Plate using the Plate Behavior of a New Multilayered Solid Element. Mechanics of Advanced Materials and Structures, Taylor & Francis, 2009, 17 (1), pp.60 - 67 [HAL] / [DOI]
2009Yann Goueffon, Catherine Mabru, Michel Labarrère, Laurent Arurault, Claire Tonon, et al. Mechanical behavior of black anodic films on 7175 aluminium alloy for space applications. Surface and Coatings Technology, Elsevier, 2009, 204 (6-7), pp.1013-1017 [HAL] / [DOI]
2009Anwar Hamasaiid, G. Wang, C. Davidson, Gilles Dour, M.S. Dargusch. Interfacial Heat Transfer during Die Casting of an Al-Si-Cu Alloy. Metallurgical and Materials Transactions A, Springer Verlag/ASM International, 2009, 40 (13), pp.3056 - 3058 [HAL] / [DOI]
2009Qi Yuhong, Philippe Lours, Yannick Le Maoult, Zhang Zongbao. Spallation Behavior of Thermally Grown Oxide Ceramic Film under Compressive Stresses. Rare Metal Materials and Engineering, 2009, 38 (2), pp.1150-1153 [HAL]
2009Amir Shahdin, Laurent Mezeix, Christophe Bouvet, Joseph Morlier, Yves Gourinat. Monitoring the effects of impact damages on modal parameters in carbon fiber entangled sandwich beams. Engineering Structures, Elsevier, 2009, 31 (12), pp.2833-2841 [HAL] / [DOI]
2009Julien Sniezewski, Vanessa Vidal, Philippe Lours, Yannick Le Maoult. Thermal barrier coatings adherence and spallation: Interfacial indentation resistance and cyclic oxidation behaviour under thermal gradient. Surface and Coatings Technology, Elsevier, 2009, ProcediaTest, 204 (6-7), pp.807-811 [HAL] / [DOI]
2009Denis Pellion, K. Jradi, A. Le Padellec, Abdelali Rennane, F. Moutier, et al. Geiger avalanche photodiodes as tentative light detectors for VHE gamma ray astronomy. Experimental Astronomy, springer Link, 2009, 27 (3), p 187-195 [HAL] / [DOI]
2009Qi Yu-Hong, Philippe Lours, Yannick Le Maoult. Spallation Process of Thermally Grown Oxides by In-Situ CCD Monitoring Technique. Journal of Iron and Steel Research, International, Elsevier, 2009, 16 (6), pp.90-94 [HAL] / [DOI]
2009Denis Pellion, K. Jradi, F. Moutier, F. Oms, C. Magenc, et al. APD photodetectors in the Geiger photon counter mode. Nuclear Instruments and Methods in Physics Research, Elsevier, 2009, A 610 (1), p 410-414 [HAL] / [DOI]
2009Amir Shahdin, Laurent Mezeix, Christophe Bouvet, Joseph Morlier, Yves Gourinat. Fabrication and mechanical testing of glass fiber entangled sandwich beams: A comparison with honeycomb and foam sandwich beams. Composite Structures, Elsevier, 2009, 9 (4), pp.404-412 [HAL] / [DOI]
2009Fabien Chauvet, Paul Duru, Sandrine Geoffroy, Marc Prat. Three Periods of Drying of a Single Square Capillary Tube. Physical Review Letters, American Physical Society, 2009, vol 103 (n° 12), pp 124502-1-124502-4 [HAL] / [DOI]
2009C. Scandian, Christine Boher, J. D. B. Mello, Farhad Rezai-Aria. Effect of molybdenum and chromium contents in sliding wear of high‐chromium white cast iron: The relationship between microstructure and wear. WEAR, 2009, 267 (1-4), pp.401-408 [HAL] / [DOI]
2009Christine Boher, Olivier Barrau, R. Gras, Farhad Rezai-Aria. A wear model based on cumulative cyclic plastic straining. WEAR, 2009, 267 (5-8), pp.1087-1094 [HAL] / [DOI]
2009Madalina Calamaz, Jérôme Limido, Mohammed Nouari, Christine Espinosa, Dominique Coupard, et al. Toward a better understanding of tool wear effect through a comparison between experiments and SPH numerical modelling of machining hard materials. International Journal of Refractory Metals and Hard Materials, Elsevier, 2009, 27, pp.595-604 [HAL] / [DOI]
2009Raquel Becerril Ortega, Bernard Calmettes, Bernard Fraysse, Pierre Lagarrigue. Des références pour des pratiques de formation. @ctivités, Association Recherches et Pratiques sur les ACTivités, 2009, 06 (1), [HAL] / [DOI]
2009M. Dargusch, A. Hamasaaid, Gilles Dour, X. Yao. Measurements of heat lossest during solidification of light metals. International Journal of Modern Physics B, World Scientific Publishing, 2009, 23 (06-07), p.802-807 [HAL] / [DOI]
2009M. Shah, Christine Boher, Sabine Le Roux, Farhad Rezai-Aria, Catherine Mabru. An investigation of the crack propagation in tool steel X38CrMoV5 (AISI H11) in SET specimens. REVUE DE METALLURGIE‐CAHIERS D INFORMATIONS TECHNIQUES, 2009, 106 (3), pp.140-145 [HAL] / [DOI]
2004Rémy Marchal, Frederic Mothe, Louis-Etienne Denaud, Bernard Thibaut, Laurent Bleron. Cutting Forces in basic and real life wood machining processes review, COST Action E35 2004-2008: Wood machining - Micromechanics and fracture. Holzforschung, De Gruyter, 2009, 63 (2), pp.157-167 [HAL]
2009Nicolas Pirc, Frederic Schmidt, Marcel Mongeau, Florian Bugarin, Francisco Chinesta. Optimization of 3D Cooling Channels in Injection Molding using DRBEM and Model Reduction. International Journal of Material Forming, Springer Verlag, 2009, 2 (1), pp.271-274 [HAL] / [DOI]
2009Tchadja Kagnaya, Christine Boher, Laurence Lambert, Myriam Lazard, Thierry Cutard. Friction at high sliding speed of WC-6Co pin versus steel disc AISI 1045 : estimation of the contact temperature. The international journal of multiphysics., Multi-Science Publishing, 2009, 3 (2), pp.141-153 [HAL] / [DOI]
2009Traian Branza, Frederic Deschaux-Beaume, G. Sierra, Philippe Lours. Study and prevention of cracking during weld-repair of heat-resistant cast steels. Journal of Materials Processing Technology, Elsevier, 2009, 209, pp.536-547 [HAL]
2009Masood Shah, Catherine Mabru, Christine Boher, Sabine Le Roux, Farhad Rezai-Aria. Crack Propagation in Tool Steel X38CrMoV5 (AISI H11) in SET Specimens. Advanced Engineering Materials, Wiley-VCH Verlag, 2009, Fatigue and Plasticity, 11 (9), pp.746-749 [HAL] / [DOI]
2009Amir Shahdin, Joseph Morlier, Yves Gourinat. Correlating low energy impact damage with changes in modal parameters: a preliminary study on composite beams. Structural Health Monitoring, SAGE Publications (UK and US), 2009, 8 (6), pp.523-536 [HAL] / [DOI]
2009Laurent Mezeix, Christophe Bouvet, Julitte Huez, Dominique Poquillon. Mechanical behavior of entangled fibers and entangled cross-linked fibers during compression. Journal of Materials Science, Springer Verlag, 2009, 44 (14), pp.3652-3661 [HAL] / [DOI]
2009Matthieu Mulle, Redouane Zitoune, Francis Collombet, Laurent Robert, Yves Henri Grunevald. Measuring strains through the thickness of a composite structural specimen subjected to bending. Experimental Mechanics, Society for Experimental Mechanics, 2009, 49 (6), p.877-880 [HAL]
2009Christophe Bouvet, Bruno Castanié, Matthieu Bizeul, Jean-Jacques Barrau. Low velocity impact modelling in laminate composite panels with discrete interface elements. International Journal of Solids and Structures, Elsevier, 2009, 46 (14-15), pp.2809-2821 [HAL] / [DOI]
2009Matthieu Mulle, Redouane Zitoune, Francis Collombet, Laurent Robert, Yves Henri Grunevald. Embedded FBGs and 3-D DIC for the stress analysis of a structural specimen subjected to bending. Composite Structures, Elsevier, 2009, 91 (1), p.48-55 [HAL]
2008Johanna Senatore, Frederic Monies, Yann Landon, Walter Rubio. Optimising positioning of the axis of a milling cutter on an offset surface by geometric error minimisation. Computer-Aided Design, Elsevier, 2008, 37 (9-10), pp.861-871 [HAL] / [DOI]
2008Vincent Velay, Denis Delagnes, Gérard Bernhart. Advances in cyclic behavior and lifetime modeling of tempered martensitic steels based on microstructural considerations. Key Engineering Materials, 2008, 378-379, pp.81-100 [HAL] / [DOI]
2008M. Dargusch, Anwar Hamasaiid, Gilles Dour. An Inverse Model to determine the Heat Transfer Coefficient and its Evolution with Time during Solidification of Light Alloys. International Journal of Nonlinear Sciences and Numerical Simulation, 2008, 9 (3), p.275-282 [HAL] / [DOI]
2008A. Duchosal, Frederic Deschaux-Beaume, Cyril Bordreuil, Gilles Fras, Philippe Lours. Method for predicting risk of cracking during weld repair of heat resistant cast steels. Science and Technology of Welding and Joining, Maney Publishing, 2008, 13, pp.126-135 [HAL] / [DOI]
2007M. s. Dargusch, Anwar Hamasaiid, Gilles Dour, T. Loulou, C. j. Davidson, et al. The Accurate Determination of Heat Transfer Coefficient and its Evolution with Time During High Pressure Die Casting of Al-9 %Si-3 %Cu and Mg-9 %Al-1 %Zn Alloys Advanced Engineering Materials, Wiley-VCH Verlag, 2007, 9 (11), pp.995 - 999 [HAL] / [DOI]
2007Gian Luca Morini, Marco Lorenzini, Stéphane Colin, Sandrine Geoffroy. Experimental analysis of pressure drop and laminar to turbulent transition for gas flows in smooth microtubes. Heat Transfer Engineering, Taylor & Francis, 2007, 28 (8-9), pp.670 - 679 [HAL] / [DOI]
2007E. Abdullah, Jean-François Ferrero, Jean-Jacques Barrau, Jean Baptiste Mouillet. Development of a new finite element for composite delamination analysis. Composites Science and Technology, Elsevier, 2007, 67 (10), pp.2208 - 2218 [HAL] / [DOI]
2007Patrick Ginet, Claude Lucat, Marc Budinger, Francis Ménil. New screen-printed thermal microactuator. IEEE Review on Advances in Micro, Nano, and Molecular Systems, 2007, 1-3, pp.851-855 [HAL]
2007Mostapha Tarfaoui, Papa-Birame Gning, Peter Davies, Francis Collombet. Scale and size Effects on Dynamic Response and Damage of Glass/Epoxy tubular structures. Journal of Composite Materials, SAGE Publications, 2007, 41 (5), pp.547-558 [HAL] / [DOI]
2007Mostapha Tarfaoui, Papa-Birame Gning, Francis Collombet. Residual strength of damaged glass/epoxy tubular structures. Journal of Composite Materials, SAGE Publications, 2007, 41 (18), pp.2165-2182 [HAL] / [DOI]
2006Denis Pellion, V. Borrel, Daniel Estève, Francis Therez, A.R. Bazer-Bachi. APD photodetectors in the Geiger photon counter mode. Nuclear Instruments and Methods in Physics Research, Elsevier, 2006, A 567, pp.41-44 [HAL] / [DOI]
2006Nicolas Driot, Claude-Henri Lamarque, Alain Berlioz. Theoretical and experimental analysis of a base-excited rotor. Journal of Computational and Nonlinear Dynamics, American Society of Mechanical Engineers (ASME), 2006, 1 (3), pp.257-263 [HAL] / [DOI]
2006Vincent Velay, Gérard Bernhart, Luc Penazzi. Cyclic behavior modeling of a tempered martensitic hot work tool steel. International Journal of Plasticity, Elsevier, 2006, 22, pp.459 - 496 [HAL] / [DOI]
2006Manuel Paredes, Emmanuel Rodriguez, Marc Sartor. Analytical Behavior Law for a Constant Pitch Conical Compression Spring. Journal of Mechanical Design, American Society of Mechanical Engineers, 2006, 128 (6), [HAL] / [DOI]
2006Yann Gueguen, Jacques Garnier, Lorenne Robert, Marc Lefranc, Isabelle Mougenot, et al. PenBase, the shrimp antimicrobial peptide penaeidin database: Sequence-based classification and recommended nomenclature. Developmental and Comparative Immunology, Elsevier, 2006, 30 (3), pp.283-288 [HAL] / [DOI]
2005Vincent Velay, Gérard Bernhart, Denis Delagnes, Luc Penazzi. A continuum damage model applied to high temperature fatigue lifetime prediction of a martensitic tool steel. Fatigue and Fracture of Engineering Materials and Structures, Wiley-Blackwell, 2005, 28 (11), pp.1009-1023 [HAL] / [DOI]
2005Nicolas Cornille, Dorian Garcia, M.A. Sutton, S.R. Mcneill, Jean-José Orteu. Calibrage d'imageurs avec prise en compte des distorsions. Instrumentation, Mesure, Métrologie, Lavoisier, 2005, 4 (3-4), p.105-124 [HAL]
2005Bertrand Tondu, Serge Ippolito, Jérémie Guiochet, Alain Daidié. A Seven-degrees-of-freedom Robot-arm Driven by Pneumatic Artificial Muscles for Humanoid Robots. International Journal of Robotics Research, SAGE Publications, 2005, 24 (4), p.257-274 [HAL] / [DOI]
2004Jean-François Ferrero, El Mahdi Yettou, Jean-Jacques Barrau, Samuel Rivallant. Analysis of a dry friction problem under small displacements: application to a bolted joint. Wear, Elsevier, 2004, 256 (11-12), pp.1135 - 1143 [HAL] / [DOI]
2004Marc Budinger, Jean-François Rouchon, Bertrand Nogarède. Analytical Modeling for the Design of a Piezoelectric Rotating-Mode Motor. IEEE/ASME Transactions on Mechatronics, Institute of Electrical and Electronics Engineers, 2004, 9 (1), pp.1 - 9 [HAL] / [DOI]
2002Stéphane Claudinon, Pascal Lamesle, Jean-José Orteu, Roland Fortunier. Continuous in situ measurement of quenching distortions using computer vision. Journal of Materials Processing Technology, Elsevier, 2002, 122, p 69-81 [HAL]
2001Jean-François Ferrero, Jean-Jacques Barrau, Jean Marie Segura, Bruno Castanié, Michel Sudre. Torsion of thin-walled composite beams with midplane symmetry. Composite Structures, Elsevier, 2001, 54 (1), pp.111 - 120 [HAL] / [DOI]
2001Jean-François Ferrero, Jean-Jacques Barrau, Jean Marie Segura, Michel Sudre, Bruno Castanié. Analytical theory for an approach calculation of non-balanced composite box beams. Thin-Walled Structures, Elsevier, 2001, 39 (8), pp.709 - 729 [HAL] / [DOI]
1998Jean-Max Redonnet, Walter Rubio, Gilles Dessein. Side milling of ruled surfaces: Optimum positioning of the milling cutter and calculation of interference. International Journal of Advanced Manufacturing Technology, Springer Verlag, 1998, 14 (7), pp.459-465 [HAL] / [DOI]
1997Jean-François Ferrero, Jean-Jacques Barrau. Study of dry friction under small displacements and near-zero sliding velocity. Wear, Elsevier, 1997, 209 (1-2), pp.322 - 327 [HAL] / [DOI]