Jean-Noël Felices




Maître de conférences à l'Institut Universitaire de Technologie de Tarbes (IUT de Tarbes)
Membre du groupe Matériaux et Structures Composites (MSC)
IUT, 1 rue Lautréamont
65016 Tarbes


☎ +33 (0) 5 62 44 42 11

Responsabilités collectives

Chef de département Génie Mécanique et productique

Responsabilités administratives

Président commission Recherche de l'IUT de Tarbes
vice président Conseil Recherche des 2 IUT de l'UPS

Production scientifique

16 contributions

Article de revue internationale avec comité de lecture

[ACL1]R. Gantois, A. Cantarel, G. Dusserre, J.-N. Felices, B. Cosson and F. Schmidt. BEM-based models to simulate the resin flow at macroscale and microscale in LCM processes. Polymer Composites. 34(8)1235–1244. 2013 [DOI]
[ACL2]R. Gantois, A. Cantarel, G. Dusserre, J.-N. Felices and F. Schmidt. Mold Filling Simulation of Resin Transfer Molding Combining BEM and Level Set Method. Applied Mechanics and Materials. 62, 57-65. 2011 [DOI]
[ACL3]R. Gantois, A. Cantarel, J.-N. Felices and F. Schmidt. Numerical simulation of Resin Transfer Molding using BEM and Level Set method. International Journal of Material Forming. 3(Suppl 1)635-638. 2010 [DOI]
[ACL4]S. Chevalier, J.-N. Felices, X. Pessoles and W. Rubio. Study of polynomial path parameterisation for side milling of sculptured surfaces. International Journal of Machining and Machinability of Materials. 8(3-4)384-407. 2010
[ACL5]F. Monies, J.-N. Felices, W. Rubio, J.-M. Redonnet and P. Lagarrigue. Five-axis NC milling of ruled surfaces: optimal geometry of a conical tool . International Journal of Production Research. 40(12)2901-2922. 2002

Article de revue avec comité de lecture non répertorié

[ACLN1]R. Gantois, A. Cantarel, J.-N. Felices, N. Pirc and F. Schmidt. BEM Simulation Of 3D Updated Resin Front For LCM Processes. Key Engineering Materials. 446, 131-136. 2010 [DOI]
[ACLN2]S. Chevalier, J.-N. Felices and W. Rubio. Modelling the Surface Generated by a Cutting Tool in Wooden Workpieces. Journal of Manufacturing Technology Research. 1, 117-136. 2009

Communication avec actes dans un congrès international ou national

[ACT1]R. Gantois, A. Cantarel, J.-N. Felices and F. Schmidt. Numerical simulation of Resin Transfer Molding using BEM and Level Set method. Proceedings of 13th ESAFORM CONFERENCE ON MATERIAL FORMING 2010
[ACT2]S. Chevalier, J.-N. Felices and W. Rubio. Detection and reduction of zones of burning in 5-axis machining of wooden parts. Proceedings of International Conference on Structural Analysis of Advanced Materials 2009
[ACT3]R. Gantois, A. Cantarel, J.-N. Felices, N. Pirc and F. Schmidt. BEM simulation of 3D updated resin front for LCM processes. Proceedings of International Conference on Structural Analysis of Advanced Materials 2009
[ACT4]C. Garnier, S. Mistou, J.-N. Felices, P. Hermel, C. Naejus and O. Pantalé. A-ACTI-5. Methodology to predict the influence of process and material parameters on impact response in composite structures. Proceedings of A-ACTI-5. International Conference on Structural Analysis of Advanced Materials 2009
[ACT5]A. Khazaeian, P. Larricq and J.-N. Felices. Deliberation on measurement conditions of surface quality of machined wood using laser optical profilometry. Proceedings of 2nd Int. Symposium on Wood Machining p.351-358 2004

Communication sans actes dans un congrès international ou national

[COM1]R. Gantois, A. Cantarel, G. Dusserre, J.-N. Felices and F. Schmidt. Mold filling simulation of resin transfer molding combining BEM and level set method . ACMA 2010 - International symposium on composites and aircraft materials 2012
[COM2]C. Garnier, S. Mistou, J.-N. Felices, P. Hermel and O. Pantalé. Methodology to predict process and materials parameters on the impact response of composites structures. Les 16èmes Journées Nationales sur les Composites- Toulouse 2009
[COM3]S. Chevalier, J.-N. Felices and W. Rubio. Génération de surfaces enveloppes pour l'usinage de pièces en Bois avec des outils de forme. XIV Colloque National de la Recherche en IUT à Villeurbanne, 2008
[COM4]J.-N. Felices, F. Eyma, M. Chaussade and P. Larricq. Side milling of swept surface on wood machining – Cutting conditions and tool path generation. COST E35 2nd Workshop Cluny 2004



INSTITUT CLEMENT ADER, 3, rue Caroline Aigle F-31400 Toulouse, France.
Livraisons : +33 (0)5 61 17 10 07
Secrétariat ICA: +33 (0)5 61 17 10 85 ou +33 (0)5 61 17 10 82
Fax : +33 (0)5 61 17 10 80