Redouane Zitoune




Maître de conférences (HDR) - Institut Universitaire de Technologie en Génie Mécanique et Productique de Toulouse (IUT GMP)
Membre du groupe Matériaux et Structures Composites (MSC)
Espace Clément Ader, 3 rue Caroline Aigle
31400 Toulouse


☎ +33 (0) 5 61 17 11 66

Activités de recherche

My current research activity focuses mainly on two axes:

1°) Machining of composite materials and multi-stacks: this part focuses on the experimental and numerical studies of the machining (drilling and trimming) of the composite and hybrid materials. The main objectives are the analysis of the damage generated during machining and the material integrity vs. the machining process and the parameters of the process. In addition, an analytical models for the prediction of the critical forces responsible of the delamination at the hole exit when drilling is developed.

 

2°) Instrumentation and manufacturing of composites materials: this part is dedicated to the identification of the variability due to the process of manufacturing thanks to the in-situ instrumentation of the composite materials by optical fiber with Bragg sensor and the digital image correlation. The composite materials concerned are made of natural fibers (flax/epoxy) and synthetic fibers (carbon/epoxy).

Activités d'enseignement

- Mechanical design, Computer-Aided Design (undergraduate students),
- Manufacturing of Composite materials (graduate students),
- Machining of composite materials (graduate students)
- Robot Kinematics
(undergraduate students),
- Stress - strain analysis
(undergraduate students),

Responsabilités collectives


Responsabilités administratives


Activités techniques de soutien à la recherche


Autres


Production scientifique

83 contributions

Article de revue internationale avec comité de lecture

[ACL1]A. Djabali , L. Toubal, R. Zitoune and S. Rechak. An experimental investigation of the mechanical behavior and damage of thick laminated carbon/epoxy composite. Composite Structures. accepted, . 2017 [DOI]
[ACL2]L. Toubal, R. Zitoune, F. Collombet and N. Rocher Gleizes. Moisture Effects on the Material Properties of a Jute/Epoxy Laminate: Impulse Excitation Technique Contribution. Journal of Natural Fibers. , 1-14. 2017 [DOI]
[ACL3]A. Hejjaji, R. Zitoune, L. Crouzeix, S. Le Roux and F. Collombet. Surface and machining induced damage characterization of abrasive water jet milled carbon/epoxy composite specimens and their impact on tensile behavior. Wear. 376-377, 1356-1364. 2017 [DOI]
[ACL4]D. Kumar, K. Singh and R. Zitoune. Impact of the carbon nanotube reinforcement in glass/epoxy polymeric nanocomposite on the quality of fiber laser drilling. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. accepted, . 2017 [DOI]
[ACL5]R. Zitoune, N. Cadorin, F. Collombet and M. Sima. Temperature and wear analysis in function of the cutting tool coating when drilling of composite structure: In situ measurement by optical fiber. Wear. 376–377, 1849-1858. 2017
[ACL6]J. Saoudi, R. Zitoune, S. Gururaja, M. Salem and S. Mezleni. Analytical and experimental investigation of the delamination during drilling of composite structures with core drill made of diamond grits: X-ray Tomography analysis. Journal of Composite Materials. , In press. 2017
[ACL7]S. Braiek, R. Zitoune, A. Ben Khalifa and M. Zidi. Experimental and numerical study of adhesively bonded ±55° filament wound tubular specimens under uniaxial tensile loading. Composite Structures. 172, 297-310. 2017
[ACL8]J. Saoudi, R. Zitoune, S. Gururaja, S. Mezlini and P. Seitier . Critical thrust force predictions during drilling: analytical modeling and X-ray tomography quantification. Composite Structures. 153(1 )886-894. 2016 [DOI]
[ACL9]R. Zitoune, K. Vijayan, F. Collombet and S. Le Roux. Experimental and numerical analysis on drilling of carbon fibre reinforced plastic and aluminium stacks. Composite Structures. 146(20)148-158. 2016 [DOI]
[ACL10]D. Kumar, K.K. Singh and R. Zitoune. Experimental investigation of delamination and surface roughness in the drilling of GFRP composite material with different drills. Advanced Manufacturing: Polymer & Composites Science. 2(1)47-56. 2016 [DOI]
[ACL11]J. Saoudi, R. Zitoune, S. Gururaja, S. Mezlini and A. Amaranath. Prediction of critical thrust force for exit-ply delamination during drilling composite laminates: Thermo-mechanical analysis. International Journal of Machining and Machinability of Materials. 18(1/2)77-98. 2016
[ACL12]R. Prakash, V. Krishnaraj , R. Zitoune and J. Sheikh-ahmad . High-Speed Edge Trimming of CFRP and Online Monitoring of Performance of Router Tools Using Acoustic Emission. Materials. 9(10)1-16. 2016 [DOI]
[ACL13]A. Beddiar, R. Zitoune, F. Collombet, Y.-H. Grunevald, T. Abadlia and N. Bourahla. Compressive behaviour of concrete elements confined with GFRP-prefabricated bonded shells. European Journal of Environmental and Civil Engineering. 19(1)65-88. 2015 [DOI]
[ACL14]M. Haddad, R. Zitoune, F. Eyma and B. Castanié. Influence of machining process and machining induced surface roughness on mechanical properties of continuous fiber composites. Experimental Mechanics. 55(3)519-528. 2015 [DOI]
[ACL15]N. Cadorin and R. Zitoune. Wear signature on hole defects as a function of cutting tool material for drilling 3D interlock composite. Wear. 332-333, 742-751. 2015 [DOI]
[ACL16]M. Saleem , R. Zitoune, I. El Sawi and H. Bougherara. Role of the Surface Quality on the Mechanical Behavior of CFRP bolted Composite joints. International Journal of Fatigue. 80, 246-256. 2015 [DOI]
[ACL17]N. Cadorin, R. Zitoune, P. Seitier and F. Collombet. Analysis of damage mechanism and tool wear while drilling of 3D woven composite materials using internal and external cutting fluid. Journal of Composite Materials. In press, . 2014 [DOI]
[ACL18]M. Haddad, R. Zitoune, F. Eyma and B. Castanié. Study of the surface defects and dust generated during trimming of CFRP: influence of tool geometry, machining parameters and cutting speed range. Composites - Part A: Applied Science and Manufacturing. 66, 142-154. 2014 [DOI]
[ACL19]M. Haddad, R. Zitoune, H. Bougherara, F. Eyma and B. Castanié. Study of trimming damages of CFRP structures in function of the machining processes and their impact on the mechanical behavior. Composites Part B: Engineering. Vol. 57, 136-143. 2014 [DOI]
[ACL20]I. El Sawi, Z. Fawaz, R. Zitoune and Z. Bougherara. An investigation of the damage mechanisms and fatigue life diagrams of flax fiber-reinforced polymer laminates. Journal of Materials Science. 49, 2338–2346. 2014 [DOI]
[ACL21]I. El Sawi, H. Bougherara, R. Zitoune and Z. Fawaz. Influence of the Manufacturing Process on the Mechanical Properties of Flax/Epoxy Composites. Journal of Biobased Materials and Bioenergy. 8, 1-8. 2014 [DOI]
[ACL22]F. Cénac, R. Zitoune, F. Collombet and M. Deleris. Abrasive Water-Jet milling of aeronautic aluminum 2024-T3. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications. 227(3). 2013 [DOI]
[ACL23]R. Zitoune, M. El Mansori and V. Krishnaraj. Tribo-functional Design of Double Cone Drill Implications in Tool Wear During Drilling of Copper mesh/CFRP/Woven ply. Wear. 302(1-2)1560-1567. 2013 [DOI]
[ACL24]B. Hachemane, R. Zitoune, B. Bezzazi and C. Bouvet. Sandwich composites impact and indentation behaviour study. Composites Part B: Engineering. 51, 1-10. 2013
[ACL25]S. Almabouacif, K. Vijayan and R. Zitoune. An investigation on cutting forces and hole quality on drilling of multimaterial. Statistical and experimental analysis. Revue des Composites et des Materiaux Avances. 23(3)437-457 . 2013
[ACL26]M. Saleem, L. Toubal, R. Zitoune and H. Bougherara. Investigating the effect of machining processes on the mechanical behaviour of composite plates with circular holes. Composites - Part A: Applied Science and Manufacturing. 55, 169–177. 2013 [DOI]
[ACL27]M. Haddad, R. Zitoune, F. Eyma and B. Castanié. Machinability and surface quality during high speed trimming of multi directional CFRP. International Journal of Machining and Machinability of Materials. 13(2/3)289-310. 2013 [DOI]
[ACL28]A. Prabukarthi, V. Krishnaraj, M. Santhosh, M. Senthilkumar and R. Zitoune. Optimization and tool life study in drilling of Titanium (Ti-6Al-4V) alloy. International Journal of Machining and Machinability of Materials. 13(2/3)138-157. 2013 [DOI]
[ACL29]V. Krishnaraj, A. Prabukarthi, A. Ramanathan, N. Elanghovan, M.S. Kumar, R. Zitoune and J.P. Davim. Optimization of machining parameters at high speed drilling of carbon fiber reinforced plastic (CFRP) laminates. Composites Part B: Engineering. 43(4)1791-1799. 2012 [DOI]
[ACL30]R. Zitoune, V. Krishnaraj, S. Almabouacif, F. Collombet, M. Sima and A. Jolin. Influence of machining parameters and new nano-coated tool on drilling performance of CFRP/Aluminium sandwich. Composites Part B: Engineering. 43(3)1480-1488. 2012 [DOI]
[ACL31]A. Mir, B. Bezzazi, R. Zitoune and F. Collombet. Study of mechanical and hygrothermal properties of agglomerated cork. Mechanika. 1, 40-45. 2012 [DOI]
[ACL32]M. Haddad, R. Zitoune, F. Eyma, B. Castanié and H. Bougherara. Surface quality and dust analysis in high speed trimming of CFRP . Applied Mechanics and Materials. 13(2/3)57-62. 2012 [DOI]
[ACL33]L. Crouzeix, F. Cenac, F. Collombet, R. Zitoune, Y.-H. Grunevald and M. Déléris. Comportement d’une réparation en escalier obtenue par Jet d’Eau Abrasif. Matériaux et Techniques. 100, 681–690. 2012
[ACL34]R. Zitoune, L. Crouzeix, F. Collombet, T. Tamine and Y.H. Grunevald. Behaviour of composite plates with drilled and moulded hole under tensile load. Composite Structures. 93(9)2384-2391. 2011 [DOI]
[ACL35]A. Mir, R. Zitoune, F. Collombet and B. Bezzazi. Study of Mechanical and Thermomechanical Properties of Jute/Epoxy Composite Laminate. Journal of Reinforced plastics and composites. 11(29)1669-1680. 2010 [DOI]
[ACL36]R. Zitoune, V. Krishnaraj and F. Collombet. Study of drilling of composite material and aluminium stack. Composite Structures. 92(5)1246-1255. 2010 [DOI]
[ACL37]M. Mulle, R. Zitoune, F. Collombet, L. Robert and Y.-H. Grunevald. Measuring strains through the thickness of a composite structural specimen subjected to bending. Experimental Mechanics. 49(6)877-880. 2009 [DOI]
[ACL38]M. Mulle, R. Zitoune, F. Collombet, L. Robert and Y.-H. Grunevald. Embedded FBGs and 3-D DIC for the stress analysis of a structural specimen subjected to bending. Composite Structures. 91(1)48-55. 2009 [DOI]
[ACL39]M. Mulle, F. Collombet, P. Olivier, R. Zitoune, C. Huchette, F. Laurin and Y.H. Grunevald. Assessment of cure-residual strains through the thickness of carbon-epoxy laminates using FBGs Part II: Technological specimen. Composites - Part A: Applied Science and Manufacturing. 40(10)1534-1544. 2009 [DOI]
[ACL40]R. Zitoune, F. Collombet and G. Hernaiz Lopez. Experimental and analytical study of the influence of HexFit® glass fiber composite manufacturing process on delamination during drilling. International Journal of Machining and Machinability of Materials. 3(3/4)326-342. 2008 [DOI]
[ACL41]R. Zitoune and F. Collombet. Numerical prediction of the thrust force responsible of delamination during the drilling of the long-fibre composite structures. Composites - Part A: Applied Science and Manufacturing. 38(3)858-866. 2007 [DOI]
[ACL42]M. Mulle, R. Zitoune, F. Collombet, P. Olivier and Y.H. Grunevald. Thermal expansion of carbon–epoxy laminates measured with embedded FBGS – Comparison with other experimental techniques and numerical simulation. Composites - Part A: Applied Science and Manufacturing. 38(5)1414-1424. 2007 [DOI]
[ACL43]F. Collombet, M. Mulle, Y.-H. Grunevald and R. Zitoune. Multiscale method for optimal design of composite structures incorporating sensors. Solid Mechanics and Its Applications . 135, 141-149. 2006 [DOI]
[ACL44]R. Zitoune, F. Collombet, R. Piquet, F. Lachaud and P. Pasquet. Experiment–calculation comparison of the cutting conditions representative of the long fiber composite drilling phase. Composites Science and Technology. 65(3/4). 2005 [DOI]

Article de revue avec comité de lecture non répertorié

[ACLN1]R. Zitoune, S. Almabouacif, F. Collombet and H. Bouguerara. Optimization of twist drill geometry for drilling CFRP and multi-material made of CFRP/Al. International Journal of Materials, Mechanics and Manufacturing. 2(4). 2014 [DOI]
[ACLN2]R. Zitoune, N. Cadorin, B. Castanié and M. Sève. Perçage d’un matériau composite tissé 3D : Influence des conditions d’usinage et de l’usure de l’outil sur les efforts de coupe et la qualité d’usinage. Revue des Composites et des Materiaux Avances. 23(3)387-404. 2013
[ACLN3]K. Vijayan, R. Zitoune and F. Collombet. Study of Drilling of Multi-Material (CFRP/Al) using Taguchi and Statistical Techniques. Journal of Materials Science. (2)95-109. 2012
[ACLN4]K. Vijayan, R. Zitoune and F. Collombet. Comprehensive Review on Drilling of Multimaterials Stacks. Journal of Machining and Forming Technologies. 2(3/4) 171-200. 2010
[ACLN5]R. Zitoune and F. Collombet. Comparaison expérience Calcul numérique des endommagements induits par perçage de structures composites fibres longues en Carbone/Epoxy. Revue des Composites et des Materiaux Avances. 15(1)105-125. 2005

Communication invitée dans un congrès national ou international

[INV1]F. Collombet, M. Mulle, H. Hernandez-moreno, R. Zitoune, B. Douchin and Y.-H. Grunevald. Benefit from embedded sensors to study polymeric composite structures. Proceedings of AIQ-ICF2008 – The first African InterQuadrennial ICF conference, Alger (Algeria). Invited lecture p.485-496 2008 [DOI]

Communication avec actes dans un congrès international ou national

[ACT1]A. Hajjaji, R. Zitoune, L. Crouzeix, F. Collombet and S. Le Roux. Impact of the abrasive water jet milling process on the damage and surface characteristics of CFRP composite.. Proceedings of 17th european conference on composites materials. Munich 2016
[ACT2]S. Braiek , R. Zitoune, A. Ben Khalifa and M. Zidi . Experimental and numerical study of adhesively bonded tubular specimens under uniaxial loading . Proceedings of Proceedings of Proceedings of 17th european conference on composites materials. Munich 2016 2016
[ACT3]J. Saoudi, R. Zitoune, S. Gururaja , S. Mezlini and P. Seitier . Analytical model of critical thrust force for exi-ply delamination during drilling: thermo-mechanical analysis . Proceedings of Proceedings of 17th european conference on composites materials. Munich 2016
[ACT4]N. Cadorin, R. Zitoune and P. Seitier . Influence of cutting parameters and wear in drilling of 3D woven carbon/epoxy composites. Proceedings of International Mechanical Engineering Congress and Exposition p.IMECE2014-37467 2014
[ACT5]S. Prabhakaran, V. Krishnarajb, K. Senthil Kumar and R. Zitoune. Sound and Vibration Damping Properties of Flax Fiber Reinforced Composites. Proceedings of p.Vol. 97, 573-581 2014 [DOI]
[ACT6]R. Zitoune, V. Krishnaraj, S. Almabouacif and F. Collombet. DESIGN OF DOUBLE CONE TWIST DRILL GEOMETRY TO IMPROVE THE HOLES QUALITY WHILE DRILLING IN MULTI-STACK MADE OF CFRP/AL. Proceedings of Proceedings of International Mechanical Engineering Congress and Exposition. P. IMECE2014-36526 2014
[ACT7]M. Haddad, R. Zitoune, H. Bougherara, F. Eyma and B. Castanié. Influence of trimming process on the surface quality and on the mechanical behavior of CFRP structures.. Proceedings of 19th International Conference on Composite Materials. 2013
[ACT8]N. Cadorin, R. Zitoune, F. Collombet, B. Castanié and M. Seve. Influence of cutting parameters and wear in drilling of 3D wowen carbon/epoxy composite. Proceedings of 19th International Conference on Composite Materials, ICCM 19, 2013 Montréal, Canada, July 28, August 2 2013
[ACT9]M. Haddad, R. Zitoune, F. Eyma and B. Castanié. Influence du procédé d'usinage sur l'usinabilité et le comportement mécanique de pièces composites. Proceedings of JNC 18, Journées Nationales sur les Composites, Nantes, 12-14 Juin 2013 2013
[ACT10]N. Cadorin, R. Zitoune, B. Castanié, F. Collombet and M. Seve. Etude expérimentale de l'influence des paramètres de coupe et de l'usure de l'outil sur la qualité de percage d'un composite tissé 3D.. Proceedings of JNC 18, Journées Nationales sur les composites, Nantes, 12-14 Juin 2013 2013
[ACT11]L. Crouzeix, Y. Davila, F. Collombet, B. Douchin, Y.-H. Grunevald and R. Zitoune. Study of step-lap repairs from elementary coupons to structural evaluators. Proceedings of SEICO13 – Sampe Europe 34th International Conference & Forum, Paris (France), March 11-12 p.167-172 2013
[ACT12]L. Crouzeix, Y. Davila, F. Collombet, B. Douchin, Y.-H. Grunevald, R. Zitoune and F. Cénac. Study of double step lap composite repairs on CFRP evaluators. Proceedings of ECCM15 - The 15th European Conference on Composite Materials, Venice (Italy), June 24-28. 2012
[ACT13]M. Haddad, R. Zitoune, F. Eyma and B. Castanié. Effect of Machining Parameters on high speed trimming of CFRP. Proceedings of 15th EUROPEAN CONFERENCE ON COMPOSITE MATERIALS 2012
[ACT14]F. Collombet, G. Luyckx, C. Sonnenfeld, N. Lammens, Y.-H. Grunevald, M. Torres, Y. Davila, B. Douchin, L. Crouzeix, H. Hernandez-moreno, R. Zitoune and R. Bazer-bachi. Embedded instrumentation: from coupon level to a representative composite part. Proceedings of SEICO12 - Sampe Europe 33rd International Technical Conference & Forum, Paris (France) p.262-291 2012
[ACT15]M. Mulle, R. Zitoune, F. Collombet, L. Robert and Y.-H. Grunevald. hrough-the-thickness material properties identification using 3D-DIC and FBG measurements. Proceedings of 13th European Conference on Composite Materials (ECCM13), Stockholm, Sweden, June 2008
[ACT16]F. Collombet, M. Mulle, H. Hernandez-moreno, B. Douchin, R. Zitoune, P. Olivier and Y.-H. Grunevald. On the use of optical fibres with bragg gratings for the identification of process-properties relations of composite structures. Proceedings of ICCM16 – The 16th International Conference on Composite Materials, Kyoto (Japan) 2007
[ACT17]F. Collombet, M. Mulle, H. Hernandez-moreno, B. Douchin, R. Zitoune, P. Olivier and Y.-H. Grunevald. De l'utilisation des fibres optiques à réseaux de Bragg pour l'établissement de relations procédé-propriétés des structures composites. Proceedings of JNC15 - 15èmes Journées Nationales sur les Composites, Marseille (France) p.975-982 2007
[ACT18]M. Mulle, R. Zitoune, F. Collombet, L. Robert and Y.-H. Grunevald. Identification de propriétés matériau sur éprouvette technologique par croisement des mesures par stéréo-corrélation d’images numériques et réseaux de Bragg avec le modèle numérique associé. Proceedings of 15èmes Journées Nationales sur les Composites (JNC'15), Marseille (France), 6-8 juin 2007
[ACT19]M. Mulle, R. Zitoune, F. Collombet, L. Robert and Y.-H. Grunevald. Déformations à coeur et en surface sur éprouvette technologique en composite - Essai de flexion 3 et 4 points. Proceedings of 8ème Colloque National en Calcul des Structures, Giens, France, mai 2007
[ACT20]M. Mulle, R. Zitoune, F. Collombet, L. Robert and Y.-H. Grunevald. Mesures de déformation à coeur sur éprouvette technologique durant la cuisson autoclave puis des essais de flexion 3 et 4 points. Proceedings of 1er Congrès Méditerranéen sur les Matériaux Composites (C2MC1), Béchar, Algérie, décembre 2006

Communication sans actes dans un congrès international ou national

[COM1]F. Collombet, L. Crouzeix, Y.-H. Grunevald, A. Cerisier, R. Zitoune, Y. Davila and B. Douchin. Repair of primary composite structures - a challenge in aeronautics for the composite solution. Franco-Chinese Symposium on Damage and Fracture of Composite Structures: Assessment and Monitoring, Tarbes (France), July 14 - 17 2015

Ouvrage scientifique

[OS1]K. Vijayan, R. Zitoune and J.P. Davim. Drilling of polymer matrix composites. Ed. Springer (http://www.springer.com/engineering/production+engineering/book/978-3-642-38344-1) 120p. 2014 ISBN:978-3-642-38345-8

Chapitre d'ouvrage scientifique

[OSC1]R. Zitoune and H. Bouguerara. Machining and drilling processes in composites manufacture: Damage and material integrity. In book Advances in Composites Manufacturing and Process Design, Chap. 9, p.177-195. Ed. Elsevier. 2015 ISBN:978-1-78242-307-2 [DOI]
[OSC2]F. Collombet, Y.-H. Grunevald, L. Crouzeix, B. Douchin, R. Zitoune, Y. Davila, A. Cerisier and R. Thévenin. Repairing composites. In book Advances in Composites Manufacturing and Process Design, Chap. 10, p.197-227. Ed. © 2015 Elsevier Ltd. 2015 ISBN:978-1-78242-307-2 [DOI]
[OSC3]M. Haddad, R. Zitoune, F. Eyma and B. Castanié. Influence of Tool Geometry and Machining Parameters on the Surface Quality and the Effect of Surface Quality on Compressive Strength of Carbon Fibre Reinforced Plastic . In book Materials Science Forum - Vol 763, p.107-125. Ed. Trans Tech Publications, Switzerland. 2013 ISBN:doi:10.4028/www.scientific.net/MSF.763.107
[OSC4]R. Zitoune, A. Mir, B. Hachemane, F. Boyer, C. Bouvet, F. Collombet and B. Bezzazi. chapter 5: Static and dynamic behaviours of composite laminate. In book Fiber reinforced composites, Chap. 5, p.. Ed. Nova publishers. 2011
[OSC5]F. Cènac, F. Collombet, M. Deliris and R. Zitoune. Abrasive Water Jet Machining of Composites. In book Machining Composite Materials, Chap. 4, p.167-180. Ed. Hardback. 2009 ISBN:9781848211704
[OSC6]F. Collombet, M. Mulle, H. Hernandez-moreno, R. Zitoune, B. Douchin and Y.-H. Grunevald. Benefit from embedded sensors to study polymeric composite structures. In book Damage and fracture mechanics - failure analysis of engineering materials and structures, p.485-496. Ed. Boukharouba Et Al Editor. 2009 ISBN:978-90-481-2668-2

Direction d'ouvrage collectif

[DO1]K. Vijayan, R. Zitoune and J.P. Davim. Special Issue on Advances in the Machining of Aerospace Materials. International Journal of Machining and Machinability of Materials. 18 (1/2) 130p. Ed. Inderscience Publishers. 2016
[DO2]R. Zitoune, R. Serra and F. Laurin. Usinage des matériaux Composites. Revue des composites et des matériaux avancés. 23(3) 130p. Ed. Lavoisier. 2013
[DO3]R. Zitoune, K. Vijayan and J.P. Davim. . International Journal of Machining and Machinability of Materials. 13 (2/3) 120p. Ed. Inderscience Publishers. 2013 ISBN:1748-572X
[DO4]R. Zitoune, K. Krishnaraj and J.P. Davim. Developments in Machining of Aerospace Materials. Journal of Machining and Forming Technologies. 4(3/4) 140p. Ed. Nova Publishers : https://www.novapublishers.com/catalog/product_info.php?products_id=37335&osCsid=8. 2012

Thèse de Doctorat ou HdR

[TH1]R. Zitoune. De la fabrication à l'usinage des matériaux composites et des multi-matériaux. Habilitation à diriger des recherches, Université Paul Sabatier. 2012



INSTITUT CLEMENT ADER, 3, rue Caroline Aigle F-31400 Toulouse, France.
Livraisons : +33 (0)5 61 17 10 07
Secrétariat ICA: +33 (0)5 61 17 10 85 ou +33 (0)5 61 17 10 82
Fax : +33 (0)5 61 17 10 80