Thomas Pottier




Maître assistant à l'Ecole Nationale Supérieure des Mines d'Albi-Carmaux (Mines Albi)
Membre du groupe Surfaces, Usinages, Matériaux et Outillages (SUMO)
Mines d'Albi-Carmaux, Campus Jarlard
81013 Albi


☎ +33 (0) 5 63 49 30 48

Production scientifique

12 contributions

Article de revue internationale avec comité de lecture

[ACL1]A. Zouaghi, V. Velay, A. Soveja, T. Pottier, M. Cheikh and F. Rézaï-aria. A multi-scale approach to investigate the nonlinear subsurface behavior and strain localization of X38CrMoV5-1 martensitic tool steel: experiment and numerical analysis. International Journal Of Plasticity. 87, 130-153. 2016 [DOI] [HAL]
[ACL2]T. Pottier, H. Louche, S. Samper, H. Favrelière, F. Toussaint and P. Vacher. Proposition of a modal filtering method to enhance heat source computation within heterogeneous thermomechanical problems. International Journal of Engineering Science. 81, 163-176. 2014 [DOI]
[ACL3]T. Pottier, G. Germain, M. Calamaz, A. Morel and D. Coupard. Sub-Millimeter Measurement of Finite Strains at Cutting Tool Tip Vicinity. Experimental Mechanics. 54(6)1031-1042. 2014 [DOI]
[ACL4]T. Pottier, H. Louche, F. Toussaint and P. Vacher. Inelastic heat fraction estimation from two successive mechanical and thermal analyses and full-field measurements. European Journal of Mechanics, A/Solids. 38, 1-11. 2013 [DOI]
[ACL5]T. Pottier, P. Vacher, F. Toussaint, H. Louche and T. Coudert. Out-of-plane testing procedure for inverse identification purpose: application in sheet metal plasticity. Experimental Mechanics. 52(7)951-963. 2012 [DOI]
[ACL6]T. Pottier, F. Toussaint and P. Vacher. Contribution of heterogeneous strain field measurements and boundary conditions modelling in inverse identification of material parameters. European Journal of Mechanics, A/Solids. 30(3)373-382. 2011 [DOI]
[ACL7]T. Pottier, M.P. Moutrille, J.B. Le Cam, X. Balandraud and M. Grédiac. Study on the use of motion compensation techniques to determine heat sources. Application to large deformations on cracked rubber specimens. Experimental Mechanics. 49(4)561-574. 2009 [DOI]

Article de revue avec comité de lecture non répertorié

[ACLN1]M. Rollin, V. Velay, L. Penazzi, T. Pottier, T. Sentenac, L. Irranzo-perez, A. Dupuy and G. Khélifati. Thermo-mechanical modeling of distortions promoted during cooling of Ti-6Al-4V part produced by superplastic forming. Materials Science Forum. 838-839, 196-201. 2016 [DOI]

Communication avec actes dans un congrès international ou national

[ACT1]M. Harzallah, T. Pottier, J. Senatore, M. Mousseigne, G. Germain and Y. Landon. A New Behavior Model for Better Understanding of Titanium alloys Ti-6Al-4V Chip Formation in Orthogonal Cutting. Proceedings of ESAFORM 2016 2016
[ACT2]A. Zouaghi, V. Velay, A. Soveja, F. Rézaï-aria, T. Pottier and M. Cheikh. Multiscale Modelling of the Surface Behaviour of AISI H11 Tool Steels. Proceedings of 10th TOOL Conference 2016 - TOOL 2016 2016

Communication sans actes dans un congrès international ou national

[COM1]A. Zouaghi, A. Soveja, F. Rézaï-aria, T. Pottier, M. Cheikh and V. Velay. Multi-scale surface modeling of the nonlinear mechanical behaviour of AISI H11 hot work tool steel. International Conference on Plasticity, Damage, and Fracture 2016

Thèse de Doctorat ou HdR

[TH1]T. Pottier. Identification paramétrique par recalage de modèles éléments finis couplée à des mesures de champs cinématiques et thermiques. Thèse de doctorat, Université de Savoie. 2010 [HAL]



INSTITUT CLEMENT ADER, 3, rue Caroline Aigle F-31400 Toulouse, France.
Livraisons : +33 (0)5 61 17 10 07
Secrétariat ICA: +33 (0)5 61 17 10 85 ou +33 (0)5 61 17 10 82
Fax : +33 (0)5 61 17 10 80