Production scientifique du Groupe SUMO

528 contributions trouvées correspondantes à votre recherche.

Article de revue internationale avec comité de lecture

[ACL1]V. Wagner, F. Barelli, G. Dessein, R. Laheurte, P. Darnis, O. Cahuc and M. Mousseigne. Comparison of the chip formations during turning of Ti64 β and Ti64 α+β . Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. , 1-11. 2017 [DOI]
[ACL2]O. Shtehin, V. Wagner, S. Seguy, Y. Landon, G. Dessein and M. Mousseigne. Stability of ball end milling on warped surface: semi-analytical and experimental analysis. International Journal of Advanced Manufacturing Technology. 89(9-12)2557-2569. 2017 [DOI]
[ACL3]P. Planques, V. Vidal, P. Lours, V. Proton, F. Crabos, J. Huez and B. Viguier. Mechanical and thermo-physical properties of plasma sprayed thermal barrier coatings : a literature review. Oxidation of Metals. 88(1-2)133-143. 2017 [DOI]
[ACL4]O. Shtehin, S. Seguy, V. Wagner, Y. Landon, G. Dessein and M. Mousseigne. Low-frequency chatter genesis during inclined surface copy-milling with ball-end mill: experimental study. Machining Science and Technology. , Accepted. 2017
[ACL5]F. Monies, I. Danis, P. Lagarrigue, P. Gilles and W. Rubio. Balancing of the transversal cutting force for pocket milling cutters: application for roughing a magnesium-rare earth alloy. International Journal of Advanced Manufacturing Technology. 89(1)45-64. 2017 [DOI]
[ACL6]V.H. Bui, P. Gilles, T. Sultan, G. Cohen and W. Rubio. A new cutting depth model with rapid calibration in abrasive water jet machining of titanium alloy. International Journal of Advanced Manufacturing Technology. , . 2017 [DOI]
[ACL7]H.L. Dorothy and P. Longère. Modelling of high strain rate Adiabatic Shear Banding induced failure: a comparison of two approaches. International Journal of Impact Engineering. In Press, . 2017 [DOI]
[ACL8]E. Copin, X. Massol, S. Amiel, T. Sentenac, Y. Le Maoult and P. Lours. Novel erbia-yttria co-doped zirconia fluorescent thermal history sensor. Smart Materials and Structures. 26(01). 2017 [DOI]
[ACL9]P. Rahme, Y. Landon, F. Lachaud, R. Piquet and P. Lagarrigue. Drilling of thick composite materials using a step gundrill. Composites - Part A: Applied Science and Manufacturing. 103, 304-313. 2017 [DOI]
[ACL10]M. Dos Santos, V. Velay, V. Vidal, G. Bernhart, G. Batalha and H. Matsumoto. Mechanical behavior of a Ti-6Al-4 V titanium alloy with microstructural evolution modeling under hot and superplastic conditions. Materialwissenschaft und Werkstofftechnik. 48(10)952-968. 2017 [DOI]
[ACL11]P. Planques, V. Vidal, P. Lours, V. Proton, F. Crabos, J. Huez and B. Viguier. Characterization of the Mechanical Properties of Thermal Barrier Coatings by 3 Points Bending Tests and Modified Small Punch Tests. Surface and Coatings Technology. , . 2017 [DOI]
[ACL12]S. Segonds, P. Seitier, C. Bordreuil, F. Bugarin, W. Rubio and J.-M. Redonnet. An analytical model taking feed rate effect into consideration for scallop height calculation in milling with torus-end cutter. Journal of Intelligent Manufacturing. online, 1-13. 2017 [DOI]
[ACL13]R. Julien, V. Velay, V. Vidal, Y. Dahan, R. Forestier and F. Rézaï-aria. Tensile behaviour of high temperature forged Ti-6Al-4V during in-situ heat treatments. Materials Letters. 208, 7-9. 2017 [DOI]
[ACL14]H. Matsumoto and V. Velay. Mesoscale modeling of dynamic recrystallization behavior, grain size evolution, dislocation density, processing map characteristic, and room temperature strength of Ti-6Al-4V alloy forged in the (α+β) region. Journal of Alloys and Compounds. 708, 404-413. 2017 [DOI]
[ACL15]H. Matsumoto, T. Nishihara, V. Velay and V. Vidal. Superplastic Property of the Ti–6Al–4V Alloy with Ultrafine-Grained Heterogeneous Microstructure. Advanced Engineering Materials. In press, . 2017 [DOI]
[ACL16]Y. Liu, I. Liu, P. Lours, T. Sentenac, V. Vidal, Z. Wang and K. Ding. Influence of isothermal aging conditions on APS TBC's interfacial fracture toughness. Surface and Coatings Technology. (313)417-424. 2017 [DOI]
[ACL17]I. Danis, F. Monies, P. Lagarrigue and N. Wojtowicz. Cutting forces and their modelling in plunge milling of magnesium-rare earth alloys. International Journal of Advanced Manufacturing Technology. 84(9-12)1801-1820. 2016 [DOI]
[ACL18]F. Abevi, A. Daidié, M. Chaussumier and S. Orieux. Static Analysis of an Inverted Planetary Roller Screw Mechanism. Journal of Mechanisms and Robotics. 8(4)041020_1-14. 2016 [DOI]
[ACL19]S. Cafieri, F. Monies, M. Mongeau and C. Bes. Plunge milling time optimization via mixed-integer nonlinear programming. Computers and Industrial Engineering. 98, 434-445. 2016
[ACL20]P. Rahme, Y. Landon, R. Piquet, F. Lachaud and P. Lagarrigue. Drilling analytical model of composite material with pilot hole. Mechanics and Industry. 17(5). 2016 [DOI]
[ACL21]K. Moussaoui, S. Segonds, W. Rubio and M. Mousseigne. Studying the measurement by X-ray diffraction of residual stresses in Ti6Al4V titanium alloy. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. , . 2016 [DOI]
[ACL22]F. Barelli, V. Wagner, R. Laheurte, G. Dessein, P. Darnis, O. Cahuc and M. Mousseigne. Orthogonal cutting of TA6V alloys with chamfered tools: Analysis of tool–chip contact lengths . Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. , 1-12. 2016 [DOI]
[ACL23]F. Abevi, A. Daidié, M. Chaussumier and M. Sartor. Static Load Distribution and Axial Stiffness in a Planetary Roller Screw Mechanism. Journal of Mechanical Design - Transactions of the ASME. 138(1)012301_1-11. 2016 [DOI]
[ACL24]M. Ullah, C. Song Wu and M. Shah. In situ delta ferrite estimation and their effects on FCPR at different orientations of multipass shielded metal arc welded SS304L. Journal of Manufacturing Processes. 21, 107-123. 2016 [DOI]
[ACL25]C. Manière, U. Kus, L. Durand, R. Mainguy, J. Huez, D. Delagnes and C. Estournes. Identification of the Norton-Green compaction model for the prediction of the Ti-6Al-4V densification during the Spark plasma sintering process. Advanced Engineering Materials. 18(10)1720-1727. 2016 [DOI]
[ACL26]P.A. Rey, J. Ledref, J. Senatore and Y. Landon. Modelling of Cutting forces in orbital drilling of titanium alloy Ti-6Al-4V. International Journal of Machine Tools and Manufacture. 106, 75–88. 2016 [DOI]
[ACL27]V. Velay, H. Matsumoto, V. Vidal and A. Chiba. Behavior modeling and microstructural evolutions of Ti–6Al–4V alloy under hot forming conditions. International Journal Of Mechanical Sciences. 108-109, 1-13. 2016 [DOI] [HAL]
[ACL28]M. Ameur, M. Habak, M. Kenane, H. Aouici and M. Cheikh. Machinability analysis of dry drilling of carbon/epoxy composites: cases of exit delamination and cylindricity error. International Journal of Advanced Manufacturing Technology. , . 2016 [DOI]
[ACL29]V. Velay and A. Michrafy. An analytical model for the prediction of hot roll temperatures in a hot rolling process. Materialwissenschaft und Werkstofftechnik. 47(12)1202-1215. 2016 [DOI]
[ACL30]A. Zouaghi, V. Velay, A. Soveja, T. Pottier, M. Cheikh and F. Rézaï-aria. A multi-scale approach to investigate the nonlinear subsurface behavior and strain localization of X38CrMoV5-1 martensitic tool steel: experiment and numerical analysis. International Journal Of Plasticity. 87, 130-153. 2016 [DOI] [HAL]
[ACL31]V. Potier, C. Pons Lelardeux, M. Lalanne and P. Lagarrigue. Making complexity fun – machining procedures in mechanical engineering. International Journal of Engineering Education. 32(2016/1)491-500. 2016
[ACL32]K. Moussaoui, F. Monies, M. Mousseigne, P. Gilles and W. Rubio. Balancing of the transverse cutting force during inclined milling and effect on the tool wear : applied to a Ti6Al4V. International Journal of Advanced Manufacturing Technology. 82(9-12)1859-1880. 2016 [DOI]
[ACL33]J.-M. Redonnet, A. Gamboa Vazquez, A. Traslosheros Michel and S. Segonds. Optimization of free-form surface machining using parallel planes strategy and torus milling cutter. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. , . 2016 [DOI]
[ACL34]Y. Liu, V. Vidal, S. Le Roux, F. Blas, F. Ansart and P. Lours. Influence of isothermal and cyclic oxidation on the apparent interfacial toughness in thermal barrier coating systems. Journal of the European Ceramic Society. 35(15)4269-4275. 2015 [DOI]
[ACL35]M. Shah, C. Mabru, M. Baccar and F. Rézaï-aria. Normalization of fatigue crack growth data in AISI H11 tool steel at room and elevated temperature . International Journal of Damage Mechanics. 24(8)1111-1140. 2015 [DOI]
[ACL36]S. Djebali, S. Segonds, J.-M. Redonnet and W. Rubio. Using the global optimisation methods to minimise the machining path length of the free-form surfaces in three-axis milling. International Journal of Production Research. 55(17)5296-5309. 2015 [DOI]
[ACL37]S. Djebali, A. Perles, S. Lemouzy, S. Segonds, W. Rubio and J.-M. Redonnet. Milling plan optimization with an emergent problem solving approach. Computers and Industrial Engineering. 87, 506-517. 2015 [DOI]
[ACL38]M. Shah, C. Mabru and F. Rezai-aria. Characterisation of the surface damage of X38CrMoV5 (AISI H11) tool steel at room temperature and 600 degrees C . Fatigue and Fracture of Engineering Materials and Structures. 38(6)742-754. 2015 [DOI]
[ACL39]K. Moussaoui, M. Mousseigne, J. Senatore, R. Chieragatti and P. Lamesle. Influence of Milling on the Fatigue Lifetime of a Ti6Al4V Titanium Alloy. Metals. 5(3)1148-1162. 2015 [DOI]
[ACL40]P. Rahme, Y. Landon, F. Lachaud, R. Piquet and P. Lagarrigue. Delamination-free drilling of thick composite materials. Composites - Part A: Applied Science and Manufacturing. 72, 148-159. 2015
[ACL41]F. Szmytka , M. Salem , F. Rezai-aria and A. Oudin . Thermal fatigue analysis of automotive Diesel piston : experimental procedure and numerical protocol. International Journal of Fatigue. 73, 48-57. 2015 [DOI]
[ACL42]S. Le Roux, F. Deschaux-Beaume, T. Cutard and P. Lours. Quantitative assessment of the interfacial roughness in multi-layered materials using image analysis: Application to oxidation in ceramic-based materials. Journal of the European Ceramic Society. 35(3)1063-1079. 2015 [DOI]
[ACL43]H. Matsumoto, V. Velay and A. Chiba. Flow behavior and microstructure in Ti–6Al–4V alloy with an ultrafine-grained α-single phase microstructure during low-temperature-high-strain-rate superplasticity. Materials and Design. 66, 611-617. 2015 [DOI]
[ACL44]E. Cabrol, C. Boher, V. Vidal and F. Rézaï-aria. Plastic straining of cobalt-based hardfacings under friction loading. Wear. 330-331, 354-363. 2015
[ACL45]K. Dohda, C. Boher, F. Rézaï-aria and P. Mahayotsanun. Tribology in metal forming at elevated temperatures. Friction. 3(1)1-27. 2015
[ACL46]M. Ladonne, M. Chérif, Y. Landon, J.-Y. K'nevez, O. Cahuc and C. De Castelbajac. Modelling the vibration assisted drilling process: identification of influential phenomena. International Journal of Advanced Manufacturing Technology. 81, 1657-1666. 2015 [DOI]
[ACL47]Z. Anjum, F. Qayyum, S. Khushnood, S. Ahmed and S.M.R. Shah. Prediction of non-propagating fretting fatigue cracks in Ti6Al4V sheet tested under pin-in-dovetail configuration: experimentation and numerical simulation. Materials and Design. 87, 750-758. 2015
[ACL48]J. Le Dref, Y. Landon, G. Dessein and C. Espinosa. Modelling kinematics and cutting forces in vibration assisted drilling. Mechanics and Industry. accepted (september 2015). 2015
[ACL49]M. Galaup, F. Segonds, C. Lelardeux and P. Lagarrigue. Mecagenius: An Innovative Learning Game for Mechanical Engineering.. International Journal of Engineering Education. 31(2015/3)786-797. 2015
[ACL50]K. Moussaoui, M. Mousseigne, J. Senatore and R. Chieragatti. The effect of roughness and residual stresses on fatigue life time of an alloy of titanium. International Journal of Advanced Manufacturing Technology. , . 2014 [DOI]
[ACL51]T. Pottier, H. Louche, S. Samper, H. Favrelière, F. Toussaint and P. Vacher. Proposition of a modal filtering method to enhance heat source computation within heterogeneous thermomechanical problems. International Journal of Engineering Science. 81, 163-176. 2014 [DOI]
[ACL52]T. Pottier, G. Germain, M. Calamaz, A. Morel and D. Coupard. Sub-Millimeter Measurement of Finite Strains at Cutting Tool Tip Vicinity. Experimental Mechanics. 54(6)1031-1042. 2014 [DOI]
[ACL53]F. Medjedoub, S. Le Roux, G. Dour and F. Rézaï-aria. Effect of local stress on the heat-checking morphology in high temperature tool steels under thermal fatigue: Transition from multi-axiality to uniaxiality. Mechanics of Materials. 69(1)159-172. 2014 [DOI]
[ACL54]T. Kagnaya, C. Boher, L. Lambert, M. Lazare and T. Cutard. Microstructural analysis of wear micromechanisms of WC-6Co cutting tools during high speed dry machining. International Journal of Refractory Metals and Hard Materials. 42, 151-162. 2014 [DOI]
[ACL55]P. Rahmé, Y. Landon, P. Lagarrigue, F. Lachaud and R. Piquet. Drilling of thick composite material with a small diameter twist drill. International Journal of Advanced Manufacturing Technology. 76, 1543–1553. 2014 [DOI]
[ACL56]L. Pin, V. Vidal, F. Blas, F. Ansart, S. Duluard, J.-P. Bonino, Y. Le Maoult and P. Lours. Optimized sol–gel thermal barrier coatings for long-term cyclic oxidation life. Journal of the European Ceramic Society. (34)961-974. 2014 [DOI]
[ACL57]T. Kagnaya, L. Lambert, M. Lazard, C. Boher and T. Cutard. Investigation and FEA-based simulation of tool wear geometry and metal oxide effect on cutting process variables. Simulation Modelling Practice and Theory. 42C, 84–97. 2014 [DOI]
[ACL58]I. Danis, N. Wojtowicz, F. Monies and P. Lagarrigue. Influence of dry plunge-milling conditions on surface integrity of magnesium alloys. International Journal of Mechatronics and Manufacturing Systems. 7(2-3)141-156. 2014 [DOI]
[ACL59]P. Gilles, G. Cohen, F. Monies and W. Rubio. Machining strategy in five-axis milling using balance of the transversal cutting force. International Journal of Advanced Manufacturing Technology. 72(9-12)1377-1387. 2014 [DOI]
[ACL60]E. Copin, T. Sentenac, Y. Le Maoult, F. Blas, F. Ansart, V. Vidal and P. Lours. Feasibility of luminescent multilayer sol-gel thermal barrier coating manufacturing for future applications in through-thickness temperature gradient sensing. Surface and Coatings Technology. 260, 90-96. 2014 [DOI]
[ACL61]M. Poitrimolt, M. Cheikh, G. Bernhart and V. Velay. Characterisation of the transverse mechanical properties of carbon/carbon composites by spherical indentation. Carbon. 66, 234-245. 2014 [DOI]
[ACL62]V. Velay, H. Matsumoto, L. Sasaki and V. Vidal. Investigation of the mechanical behaviour of Ti-6Al-4V alloy under hot forming conditions: Experiment and Modelling. Materialwissenschaft und Werkstofftechnik. 45(9)847–853. 2014 [DOI]
[ACL63]P. Lepesant, C. Boher, Y. Berthier and F. Rézaï-aria. A phenomenological model of the third body particles circulation in a high temperature contact. Wear. 298, 66-79. 2013
[ACL64]C. Bellot, P. Lamesle and D. Delagnes. XRD synchrotron study of carbide precipitation in martensitic steels during tempering. Acta Metallurgica Sinica (English Letters). 26(5)553-557. 2013 [DOI]
[ACL65]M.-C. Robin, D. Delagnes, R. Logé, P.-O. Bouchard, S. Da Costa, M. Monteagudo-galindo and V. Velay. Thermo-mechanical fatigue behaviour of welded tubular parts made of ferritic stainless steel. International Journal of Fatigue. 54, 84-98. 2013 [DOI]
[ACL66]F. Pettinari-sturmel, B. Kedjar, J. Douin, C. Gatel, D. Delagnes and A. Coujou. TEM study of structural hardening in a new martensitic steel for aeronautic application. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 576, 290-297. 2013 [DOI]
[ACL67]S. Le Roux and F. Rézaï-aria. Topological and metric properties of microscopic crack patterns: application to thermal fatigue of high temperature tool steels. Journal of Physics D - Applied Physics. 46(29)295301. 2013 [DOI]
[ACL68]A. Nafi, M. Cheikh and O. Mercier. Identification of mechanical properties of CuSil-steel brazed structures joints : A numerical Approach . Journal of Adhesion Science and Technology. 27(24)2705-2713. 2013 [DOI]
[ACL69]J.-M. Redonnet, S. Djebali, S. Segonds, J. Senatore and W. Rubio. Study of the effective cutter radius for end milling of free-form surfaces using a torus milling cutter. CAD Computer Aided Design. 45(6)951–962. 2013 [DOI]
[ACL70]S. Le Roux, F. Medjedoub, G. Dour and F. Rézaï-aria. Role of heat-flux density and mechanical loading on the microscopic heat-checking of high temperature tool steels under thermal fatigue experiments. International Journal of Fatigue. 51, 15-25. 2013 [DOI]
[ACL71]E. Cabrol, C. Bellot, P. Lamesle, D. Delagnes and E. Povoden-karadeniz. Experimental investigation and thermodynamic modeling of molybdenum and vanadium-containing carbide hardened iron-based alloys. Journal of Alloys and Compounds. 556, 203-209. 2013 [DOI]
[ACL72]S. Le Roux, F. Medjedoub, G. Dour and F. Rézaï-aria. Image analysis of microscopic crack patterns applied to thermal fatigue heat-checking of high temperature tool steels. Micron. 44, 347-358. 2013 [DOI]
[ACL73]M. Mousseigne, Y. Landon, S. Seguy, G. Dessein and J.-M. Redonnet. Predicting the dynamic behaviour of torus milling tools when climb milling using the stability lobes theory. International Journal of Machine Tools and Manufacture. 65, 47-57. 2013 [DOI]
[ACL74]K. Faria-pinho, C. Boher and C. Scandian. Effect of molybdenum and chromium contents on sliding wear of high-chromium white cast iron at high temperature. Lubrication Science. 25, 153-162. 2013
[ACL75]A. Duchosal, F. Deschaux-beaume, P. Lours, S. Haro and G. Fras. Analysis of weld-cracking and improvement of the weld-repair process of superplastic forming tools. Materials and Design. 46, 731-739. 2013 [DOI]
[ACL76]X. Pessoles, Y. Landon, S. Segonds and W. Rubio. Optimisation of workpiece setup for continuous five-axis milling: application to a five-axis BC type machining centre . International Journal of Advanced Manufacturing Technology. 65, 67-79. 2013 [DOI]
[ACL77]S. Segonds, C. Bes, F. Monies and J.-M. Redonnet. Variability influence of machining context on tool tips wear estimation - Application to dry turning of 42CrMo4 steel. International Journal of Manufacturing Research. 8(3)277 - 295. 2013 [DOI]
[ACL78]E. Vermesse, C. Mabru and L. Arurault. Surface integrity after pickling and anodization of Ti-6Al-4V titanium alloy . Applied Surface Science. 285, 629-637. 2013
[ACL79]M. Chaussumier, C. Mabru, M. Shahzad, R. Chieragatti and F. Rézaï-aria. A predictive fatigue life model for anodized 7050 aluminium alloy. International Journal of Fatigue. 48, 205-213. 2013 [DOI] [OATAO]
[ACL80]L. Pin, C. Pilgrim, J. Feist, Y. Le Maoult, F. Ansart and P. Lours. Characterisation of thermal barrier sensor coatings synthesised by sol-gel route. Sensors and Actuators, A: Physical. , . 2013 [DOI]
[ACL81]B. Romuald, M. Cheikh, Y. Barranger, P. Doumalin, A. Germaneau and J.-C. Dupré. Experimental and numerical study of the load distribution in a ball screw system. Journal of Mechanical Science and Technology. , . 2013
[ACL82]K. Moussaoui, M. Mousseigne, J. Senatore, P. Lagarrigue and Y. Caumel. Influence of milling on surface integrity of Ti-6Al-4V. Advanced Materials Research. 698, 127-137. 2013 [DOI]
[ACL83]M. Cheikh and A. Fermy . Prototype fretting device and some experimental results. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology. , . 2013 [DOI]
[ACL84]Y. Landon and M. Cherif. Characterization of the surface quality of holes drilled in CFRP laminates. Advanced Materials Research. 201 - 698, 107-116. 2013 [DOI]
[ACL85]L. Tapie, B. Mawussi, W. Rubio and B. Furet. Machining of complex-shaped parts with guidance curves. International Journal of Advanced Manufacturing Technology. , . 2013 [DOI]
[ACL86]J. Le Dref, F. Eyma, G. Dessein, L.-E. Denaud and Y. Landon. Comparative study of tools in drilling composites T700-M21 and T800-M21. Advanced Materials Research. 201 - 698, 59-68. 2013 [DOI]
[ACL87]P. Gilles, G. Cohen, F. Monies and W. Rubio. Torus cutter positioning in 5-axis milling using balance of the transversal cutting force. International Journal of Advanced Manufacturing Technology. 66(5-8)965-973. 2013 [DOI]
[ACL88]J. Senatore, K. Moussaoui, S. Segonds, F. Monies and W. Rubio. Analysis of drift in iso-scallop planning – Machining by regions. International Journal of Advanced Manufacturing Technology. 67, 719-732. 2013
[ACL89]L. Pin, F. Ansart, J.-P. Bonino, Y. Le Maoult, V. Vidal and P. Lours. Reinforced sol gel thermal barrier coatings and their cyclic oxidation life. Journal of the European Ceramic Society. 33(2)269-276. 2013 [DOI]
[ACL90]K. Ben Slima, L. Penazzi, C. Mabru and F. Ronde-Oustau. Fatigue analysis-based numerical design of stamping tools made of cast iron. . 67(5-8)1643-1650. 2012 [DOI]
[ACL91]S. Le Roux, C. Boher, L. Penazzi, C. Dessain and B. Tavernier. A methodology and new criteria to quantify the adhesive and abrasive wear damage on a die radius using white light profilometry. Tribology International. 52, 40-49. 2012 [DOI]
[ACL92]C. Boher, S. Le Roux, L. Penazzi and C. Dessain. Experimental investigation of the tribological behavior and wear mechanisms of tool steel grades in hot stamping of a high-strength boron steel. Wear. 294-295, 286-295. 2012 [DOI]
[ACL93]C. Demian, S. Costil, P. Sallamand, A. Soveja, H. Liao and S. Matteï. Laser densification of organic coating: Effects of laser wavelength, operating parameters and substrate properties. Surface and Coatings Technology. 206(16)3526–3533. 2012 [DOI]
[ACL94]M. Perrut, M.-H. Mathon and D. Delagnes. Small-angle neutron scattering of multiphase secondary hardening steels. Journal of Materials Science. 47(4)1920-1929. 2012 [DOI]
[ACL95]X. Pessoles, J.-M. Redonnet, S. Segonds and M. Mousseigne. Modelling and optimising the passage of tangency discontinuities in NC linear paths . International Journal of Advanced Manufacturing Technology. 58(5-8)631–642. 2012 [DOI]
[ACL96]L. Robert, V. Velay, N. Decultot and S. Ramde. Identification of hardening parameters using finite element models and full-field measurements: some case studies. Journal of Strain Analysis for Engineering Design. 47(1)3-17. 2012 [DOI] [HAL]
[ACL97]M. Cusic, F. Abu-farha, P. Lours, Y. Le Maoult, G. Bernhart and M. Kraisheh. Towards superplastic forming of AZ31 magnesium alloy with controlled microstructure. Materialwissenschaft und Werkstofftechnik. 43(9)810-816. 2012 [DOI]
[ACL98]M. Shahzad, M. Chaussumier, R. Chieragatti, C. Mabru and F. Rézaï-aria. Effect of sealed anodic film on fatigue performance of 2214-T6 aluminium alloy. Surface and Coatings Technology. 206(11-12)2733-2739. 2012 [DOI]
[ACL99]Y. Goueffon, G. Aldebert, C. Mabru, L. Arurault, C. Tonon and P. Guigue. Flaking of black anodic films in space environment: Ageing and numerical simulation. Mechanics of Materials. 45, 72-82. 2012 [DOI] [OATAO]
[ACL100]M. Shah, C. Mabru, F. Rézaï-aria, I. Souki and R.A. Pasha. An estimation of stress intensity factor in a clamped SE(T) specimen through numerical simulation and experimental verification : case of FCGR of AISI H11 tool steel. Acta Metallurgica Sinica (English Letters). 25(4)307-319. 2012
[ACL101]L. Benezech, Y. Landon and W. Rubio. Study of manufacturing defects and tool geometry optimisation for multi-material stack drilling. Advanced Materials Research. 423, 1-11. 2012 [DOI]
[ACL102]D. Delagnes, F. Pettinari-sturmel, M.-H. Mathon, R. Danoix, F. Danoix, C. Bellot , P. Lamesle and A. Grellier. Cementite-free martensitic steels: A new route to develop high strength/high toughness grades by modifying the conventional precipitation sequence during tempering. Acta Materialia. 60(16)5877-5888. 2012 [DOI]
[ACL103]J. Senatore, S. Segonds, W. Rubio and G. Dessein. Correlation between machining direction, cutter geometry and step-over distance in 3-axis milling: application to milling by zones. CAD Computer Aided Design. 44, 1151-1160. 2012
[ACL104]V. Velay, T. Cutard and N. Guegan. Thermal behaviour modelling of superplastic forming tools. Materialwissenschaft und Werkstofftechnik. 43(9)799-804 . 2012 [DOI]
[ACL105]F. Danoix, R. Danoix, J. Akre, A. Grellier and D. Delagnes. Atom probe tomography investigation of assisted precipitation of secondary hardening carbides in a medium carbon martensitic steels. Journal of Microscopy. 244(3)305-310. 2011 [DOI]
[ACL106]P. Gilles, J. Senatore, S. Segonds, F. Monies and W. Rubio. Determination of angular fields outside low and high collisions to mill free-form surfaces on 5-axis CNC machines . International Journal of Production Research. 50(4)1045-1061. 2011 [DOI]
[ACL107]G. Cohen, P. Gilles, S. Segonds, M. Mousseigne and P. Lagarrigue. Thermal and mechanical modeling during dry turning operations . International Journal of Advanced Manufacturing Technology. 58(1-4)133-140. 2011 [DOI]
[ACL108]J.-J. Orteu, F. Bugarin, J. Harvent, L. Robert and V. Velay. Multiple-Camera Instrumentation of a Single Point Incremental Forming Process Pilot for Shape and 3D Displacement Measurements: Methodology and Results. Experimental Mechanics. 51(4)625-639. 2011 [DOI] [HAL]
[ACL109]Z. Zhang, D. Delagnes and G. Bernhart. Cyclic behaviour and plastic strain memory effect of 55NiCrMoV7 steel under low cycle fatigue. Rare Metals. 30(SI)443-446. 2011 [DOI]
[ACL110]A. Michrafy, H. Diarrab, J. Dodds, M. Michrafy and L. Penazzi. Analysis of strain stress state in roller compaction process. Powder Technology. 208(2)417-422. 2011 [DOI]
[ACL111]P. Rahmé, Y. Landon, F. Lachaud, R. Piquet and P. Lagarrigue. Analytical models of composite material drilling. International Journal of Advanced Manufacturing Technology. 52(5)609-617. 2011 [DOI]
[ACL112]P. Rahmé, Y. Landon, P. Lagarrigue, F. Lachaud and R. Piquet. Drilling thick composite materials using large diameter drills. International Journal of Machining and Machinability of Materials. 10(3)202-221. 2011
[ACL113]J. Limido, C. Espinosa, M. Salaün, C. Mabru, R. Chieragatti and J.-L. Lacome. Metal cutting modelling SPH approach. International Journal of Machining and Machinability of Materials. 9(3-4)177-196. 2011 [DOI] [OATAO]
[ACL114]T. Kagnaya, M. Lazard, L. Lambert, C. Boher and T. Cutard. Temperature evolution in a WC-6%Co cutting tool during turning machining: experiment and finite element simulations. WSEAS Transactions on Heat and Mass Transfer. 6(3)71-80. 2011
[ACL115]J. Sniezewski, Y. Le Maoult and P. Lours. Buckling and spalling failure of alumina grown by oxidation on ODS FeCrAl alloys. Materials at High Temperatures. 28(1)17-20. 2011 [DOI]
[ACL116]M. Shahzad, M. Chaussumier, R. Chieragatti, C. Mabru and F. Rézaï-aria. Surface characterization and influence of anodizing process on fatigue life of Al 7050 alloy. Materials and Design. 32(6)3328-3335. 2011 [DOI] [OATAO]
[ACL117]L. Pin, F. Ansart, J.-P. Bonino, Y. Le Maoult, V. Vidal and P. Lours. Processing, repairing and cyclic oxidation behaviour of sol-gel thermal barrier coatings. Surface and Coatings Technology. 206, 1609-1614. 2011 [DOI]
[ACL118]A. Hamasaiid, G. Dour, T. Loulou and M.S. Dargusch. A predictive model for the evolution of the thermal conductance at the casting–die interfaces in high pressure die casting. International Journal of Thermal Sciences. 49(2)365–372. 2010 [DOI]
[ACL119]S. Chevalier, J.-N. Felices, X. Pessoles and W. Rubio. Study of polynomial path parameterisation for side milling of sculptured surfaces. International Journal of Machining and Machinability of Materials. 8(3-4)384-407. 2010
[ACL120]Y. Goueffon, L. Arurault, S. Fontorbes, C. Mabru, C. Tonon and P. Guigue. Chemical characteristics, mechanical and thermo-optical properties of black anodic films prepared on 7175 aluminium alloy for space applications . Materials Chemistry and Physics. 120(2-3)636-642. 2010 [DOI] [OATAO]
[ACL121]J. Sniezewski, Y. Le Maoult and P. Lours. Oxidation and spallation of FeCrAl alloys and Thermal Barrier Coatings: in situ investigation under controlled temperature gradient . Materials at High Temperatures. 27(2)101-108. 2010 [DOI]
[ACL122]M. Shahzad, M. Chaussumier, R. Chieragatti, C. Mabru and F. Rézaï-aria. Influence of surface treatments on fatigue life of Al 7010 alloy. Journal of Materials Processing Technology. 210(13)1821-1826. 2010 [DOI] [OATAO]
[ACL123]J. Sniezewski, Y. Le Maoult, P. Lours, L. Pin, V. Minvie Bekale, D. Monceau, D. Oquab, J. Fenech, F. Ansart and J.-P. Bonino. Sol-gel thermal barrier coatings : optimization of the manufacturing route and durability under cyclic oxidation. Surface and Coatings Technology. 205, 1256-1261. 2010 [DOI]
[ACL124]X. Pessoles, Y. Landon and W. Rubio. Kinematic modelling of a 3-axis NC machine tool in linear and circular interpolation. International Journal of Advanced Manufacturing Technology. 47(5)639-655. 2010 [DOI]
[ACL125]Y. Goueffon, C. Mabru, M. Labarrère, L. Arurault, C. Tonon and P. Guigue. Investigations into the coefficient of thermal expansion of porous films prepared on AA7175 T7351 by anodizing in sulphuric acid electrolyte. Surface and Coatings Technology. 205(7)2643-2648. 2010 [DOI] [OATAO]
[ACL126]X. Pessoles, Y. Landon, M. Mousseigne and W. Rubio. Simulation of the behaviour of CNC machine-tools in three-axis milling of sculptured surfaces. International Journal of Machining and Machinability of Materials. 8(3-4)326-338. 2010 [DOI]
[ACL127]A. Hamasaiid, G. Wang, C. Davidson, G. Dour and M.S. Dargusch. Interfacial Heat Transfer during Die Casting of an Al-Si-Cu Alloy. Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. 40A(13)3056-3058. 2009 [DOI]
[ACL128]M. Shah, C. Mabru, C. Boher, S. Le Roux and F. Rézaï-aria. Crack Propagation in Tool Steel X38CrMoV5 (AISI H11) in SET Specimens. Advanced Engineering Materials. 11(9)695-754. 2009 [DOI]
[ACL129]L. Thilly, S. Van Petegem, P.-O. Renault, F. Lecouturier, V. Vidal, B. Schmitt and H. Van Swygenhovenb. A new criterion for elasto-plastic transition in nanomaterials: Application to size and composite effects on Cu–Nb nanocomposite wires. Acta Materialia. 57(11)3157-3169. 2009 [DOI] [HAL]
[ACL130]C. Scandian, C. Boher, J. De Mello and F. Rézaï-aria. Effect of molybdenum and chromium contents in sliding wear of high-chromium white cast iron: The relationship between microstructure and wear. Wear. 267(1-4)401-408. 2009 [DOI]
[ACL131]T. Kagnaya, C. Boher, L. Lambert, M. Lazard and T. Cutard. Wear mechanisms of WC–Co cutting tools from high-speed tribological tests. Wear. 267(5-8)890-897. 2009 [DOI]
[ACL132]M. Calamaz, J. Limido, M. Nouari, C. Espinosa, D. Coupard, M. Salaün, F. Girot and R. Chieragatti. Toward a better understanding of tool wear effect through a comparison between experiments and SPH numerical modelling of machining hard materials. International Journal of Refractory Metals and Hard Materials. 27(3)595–604. 2009 [DOI] [OATAO]
[ACL133]P. Rahmé, Y. Landon, P. Lagarrigue, F. Lachaud, R. Piquet, B. Marguet, J. Bouriquet and C. Leroy. Chisel Edge Effect on Delamination when Drilling Thick Composite Materials with a Twist Drill. SAE International Journal of Aerospace. 1, 776-781. 2009
[ACL134]M.S. Dargusch, A. Hamasaaid, G. Dour and X. Yao. Measurements of heat lossest during solidification of light meals. International Journal of Modern Physics B. 23(6-7)802-807. 2009 [DOI]
[ACL135]V. Vidal, L. Thilly, S. Van Petegem, U. Stuhr, F. Lecouturier, P.-O. Renault and H. Van Swygenhoven. Plasticity of nanostructured Cu–Nb-based wires: Strengthening mechanisms revealed by in situ deformation under neutrons. Scripta Materialia. 60(3)171-174. 2009 [DOI]
[ACL136]Y. Qi, P. Lours, Y. Le Maoult and Z.B. Zhang. Spallation Behavior of Thermally Grown Oxide Ceramic Film under Compressive Stresses. Rare Metal Materials and Engineering. 38(2)1150-1153. 2009
[ACL137]P. Gilles, G. Cohen, F. Monies and W. Rubio. Dynamic behaviour improvement for a torus milling cutter using balance of the transversal cutting force. International Journal of Advanced Manufacturing Technology. 40(7-8)669-675. 2009 [DOI]
[ACL138]C. Boher, O. Barrau, R. Gras and F. Rézaï-aria. A wear model based on cumulative cyclic plastic straining. Wear. 267(5-8)1087-1094. 2009 [DOI]
[ACL139]M. Shah, C. Boher, S. Le Roux, F. Rézaï-aria and C. Mabru. An investigation of the crack propagation in tool steel X38CrMoV5(AISI H11) in SET specimens. Revue de Métallurgie - Cahiers d'Informations Techniques. 106(3)140-145. 2009 [DOI] [OATAO]
[ACL140]T. Branza, F. Deschaux-beaume, V. Velay and P. Lours. A microstructural and low-cycle fatigue investigation of weld-repaired heat-resistant cast steels. Journal of Materials Processing Technology. 209(2)944-953. 2009 [DOI]
[ACL141]Y. Goueffon, L. Arurault, C. Mabru, C. Tonon and P. Guigue. Black anodic coatings for space applications: study of the process parameters, characteristics and mechanical properties. Journal of Materials Processing Technology. 209(11)5145-5151 . 2009 [DOI] [OATAO]
[ACL142]T. Branza, F. Deschaux-beaume and P. Lours. Study and prevention of cracking during weld-repair of heat-resistant cast steels. Journal of Materials Processing Technology. 209(1)944-953. 2009 [DOI]
[ACL143]Y. Qi, P. Lours and Y. Le Maoult. Spallation process of thermally grown oxides by in situ CCD monitoring technique. Journal of Iron and Steel Research International. 16(6)90-94. 2009
[ACL144]J. Sniezewski, V. Vidal, P. Lours and Y. Le Maoult. Thermal Barrier Coatings adherence and spallation : interfacial indentation resistance and cyclic oxidation behaviour under thermal gradient. Surface and Coatings Technology. 204, 807-811. 2009 [DOI]
[ACL145]Y. Goueffon, C. Mabru, M. Labarrère, L. Arurault, C. Tonon and P. Guigue. Mechanical Behaviour Of Black Anodic Films On 7175 Aluminium Alloy For Space Applications. Surface and Coatings Technology. 204(6-7)1013-1017. 2009 [DOI] [OATAO]
[ACL146]K. Mocellin, M. Ferrarro, V. Velay, R. Logé and F. Rézaï-aria. Numerical Life Prediction of Mechanical Fatigue for Hot Forging Tools. International Journal of Material Forming. 2, 129-132. 2009 [DOI] [HAL]
[ACL147]Y. Fares, M. Chaussumier and A. Daidié. Comparative study of the mechanical characteristics of 42CrMo4 class 8.8 steel bolts depending on the manufacture process . Mécanique & Industries. 9(4)315-322. 2008 [DOI]
[ACL148]J. Senatore, F. Monies, Y. Landon and W. Rubio. Optimising positioning of the axis of a milling cutter on an offset surface by geometric error minimisation . International Journal of Advanced Manufacturing Technology. 37(9-10)861-871. 2008 [DOI]
[ACL149]J. Senatore, Y. Landon and W. Rubio. Analytical estimation of error in flank milling of ruled surfaces. CAD Computer Aided Design. 40(5)595-603. 2008 [DOI]
[ACL150]G. Cohen, S. Segonds, M. Mousseigne and P. Lagarrigue. Tool Flank Wear Influence On Workpiece Heating In Dry Machining . International Journal of Machining and Machinability of Materials. , . 2008 [DOI]
[ACL151]Z. Zhang, G. Bernhart and D. Delagnes. Cyclic behaviour constitutive modelling of a tempered martensitic steel including ageing effect. International Journal of Fatigue. 30(4)706-716. 2008 [DOI]
[ACL152]D.H. Nguyen, M. Lazard, F. Bilteryst, P. Lamesle and G. Dour. Modelling the brazed assembly by the coupling of the eXtended Finite Element and the matched asymptotic development methods. International Journal of Material Forming. 1, 1119-1122. 2008 [DOI]
[ACL153]P. Lours, J. Sniezewski, Y. Le Maoult and B. Pieraggi. Direct observations and analysis of the spallation of alumina scales grown on PM2000 alloy. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 480(1-2)40-48. 2008 [DOI]
[ACL154]J. Sniezewski, Y. Le Maoult and P. Lours. In Situ Thermal Gradient Controlled Investigation of Spallation - Experimental Design and Preliminary Results. Materials Science Forum. 595-598, 1135-1143. 2008
[ACL155]J. Rishmany, C. Mabru, R. Chieragatti and F. Rézaï-aria. Simplified Modelling Of The Behaviour Of A 3d Periodic Structures Such As Aircraft Heat Exchanger. International Journal Of Mechanical Sciences. 50(6)1114-1122 . 2008 [DOI] [OATAO]
[ACL156]E. Herny, P. Lours, E. Andrieu, J.-M. Cloué and P. Lagain. Evolution of microstructure and impact-strength energy in thermally and thermomechanically aged 15-5 PH. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications. 222, 209-304. 2008 [DOI]
[ACL157]M. Suraratchai, J. Limido , C. Mabru and R. Chieragatti. Modelling The Influence Of Machined Surface Roughness On The Fatigue Life Of Aluminium Alloy. International Journal of Fatigue. 30(12)2119-2126. 2008 [DOI] [OATAO]
[ACL158]A. Duchosal, F. Deschaux-beaume, C. Bordreuil, G. Fras and P. Lours. Method for predicting risk of cracking during weld repair of heat resistant cast steels. Science and Technology of Welding and Joining. 13(2)126. 2008 [DOI]
[ACL159]P. Rahmé, Y. Landon, P. Lagarrigue, F. Lachaud and R. Piquet. Study into causes of damage to carbon epoxy composite material during the drilling process. International Journal of Machining and Machinability of Materials. 3(3-4)309-325. 2008 [DOI]
[ACL160]S. Segonds, C. Bes, G. Cohen and Y. Landon. Statistical Study Of The Spindle Dilatation Phenomena—application To A Nc Lathe . International Journal of Machine Tools and Manufacture. 47(15)2307-2311. 2007 [DOI]
[ACL161]P. Gilles, F. Monies and W. Rubio. Optimum orientation of a torus milling cutter: Method to balance the transversal cutting force. International Journal of Machine Tools and Manufacture. 47(15)2263–2272. 2007
[ACL162]Z. Zhang, Y.-H. Qi, D. Delagnes and G. Bernhart. Microstructure Variation and Hardness Diminution During Low Cycle Fatigue of 55NiCrMoV7 Steel . Journal of Iron and Steel Research International. 14(6)68-73. 2007 [DOI]
[ACL163]P. Michaud, D. Delagnes, P. Lamesle, M.-H. Mathon and C. Levaillant . The effect of the addition of alloying elements on carbide precipitation and mechanical properties in 5% chromium martensitic steels. Acta Materialia. 55(14)4877-4889. 2007 [DOI]
[ACL164]M. Oudjene, J.L. Batoz, L. Penazzi and F. Mercier. Methodology for analyzing and designing layered tools for sheet metal stamping. Journal of Materials Processing Technology. 189(1-3)334-343. 2007
[ACL165]O. Oudjene, M. Penazzi and J.L. Batoz. Towards the three-dimensional FE analysis of rapid prototyping tools for sheet metal stamping process,. Finite Elements in Analysis and Design. 43(8)611-619. 2007
[ACL166]M. Cheikh, S. Quilici and G. Cailletaud. Presentation of KI-COF, a phenomenological model of variable friction in fretting contact. Wear. 262(7-8)924. 2007
[ACL167]P. Lours, Y. Qi, Y. Le Maoult and B. Pieraggi. in situ and ex situ investigation of the spallation of thermally grown oxides. Materials Science Forum. 539-543, 1134. 2007
[ACL168]Z. Zhang, Y.-H. Qi, X.-J. Wang, D. Delagnes and G. Bernhart. Relationship between microstructure and tempering time and temperature in 55NiCrMoV7 steel . transactions of materials and heat treatment. 28(2)73-76. 2007
[ACL169]Z. Zhang , D. Delagnes and G. Bernhart. Ageing effect on cyclic plasticity of a tempered martensitic steel. International Journal of Fatigue. 29(2)336-346. 2007 [DOI]
[ACL170]J. Senatore, F. Monies, J.-M. Redonnet and W. Rubio. Improved positioning for side milling of ruled surfaces : analysis of the rotation axis’s influence on machining error. International Journal of Machine Tools and Manufacture. 47(6)934-945. 2007
[ACL171]S. Segonds, Y. Landon, F. Monies and P. Lagarrigue. Method For Rapid Characterisation Of Cutting Forces In End Milling Considering Runout . International Journal of Machining and Machinability of Materials. 1(1)45-61. 2006
[ACL172]S. Segonds, G. Cohen, Y. Landon, F. Monies and P. Lagarrigue. Characterising The Behaviour Of Workpieces Under The Effect Of Tangential Cutting Force During Nc Turning. Application To Machining Of Slender Workpieces . Journal of Materials Processing Technology. 171(3)471-479. 2006 [DOI]
[ACL173]V. Velay, G. Bernhart and L. Penazzi. Cyclic behavior modeling of a tempered martensitic hot work tool steel. International Journal Of Plasticity. 33(3)459-496. 2006 [DOI] [HAL]
[ACL174]P. Gilles, J.-M. Redonnet, P. Lagarrigue, R. Beceril, B. Fraysse and V. Boucharessas. Improving NC milling skills through practise of simulated work. Materials Science Forum. 526, 121-126. 2006
[ACL175]P. Gilles, F. Monies and W. Rubio. Modelling cutting forces in milling on torus cutters. International Journal of Machining and Machinability of Materials. 1(2)166-185. 2006 [DOI]
[ACL176]C. Mabru, N. Stephan and R. Chieragatti. Influence Of Coating On The Thermal Resistance Of A Ni-based Superalloy. International Journal of Damage Mechanics. 15(4)375-391 . 2006 [DOI] [OATAO]
[ACL177]S. Segonds, J.-M. Redonnet, Y. Landon, C. Bes and P. Lagarrigue. Characterisation Of The Workpiece Dilatation Phenomenon During Milling Using The Neural Network Method. Application To The Nc Turning . International Journal of Advanced Manufacturing Technology. 27(1-2)83-89. 2005 [DOI]
[ACL178]V. Velay, G. Bernhart, D. Delagnes and L. Penazzi. A continuum damage model applied to high-temperalture fatigue lifetime prediction of a martensitic tool steel. Fatigue and Fracture of Engineering Materials and Structures. 28(11)1009-1023. 2005 [DOI] [HAL]
[ACL179]C. Boher, D. Attaf, L. Penazzi and C. Levaillant. Wear behaviour on the radius portion of a die in deep-drawing : identification, localisation and evolution of the surface damage. Wear. 259(7-12)1097-1108. 2005
[ACL180]D. Delagnes, P. Lamesle, M.-H. Mathon, N. Mébarki and C. Levaillant. Influence of silicon content on the precipitation of secondary carbides and fatigue properties of a 5%Cr tempered martensitic steel. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 394(1-2)435-444. 2005 [DOI]
[ACL181]G. Dour, F. Medjedoub, S. Le Roux, G. Diaconu and F. Rézaï-aria. Normalized thermal stresses analysis to design a thermal fatigue experiment. Journal of Thermal Stresses. 28(1)1-16. 2005 [DOI]
[ACL182]J. Senatore, F. Monies, J.-M. Redonnet and W. Rubio. Analysis of improved positioning of five-axis ruled surface milling using envelope surface. CAD Computer Aided Design. 37(10)989-998. 2005
[ACL183]C.Y. Gao, P. Lours and G. Bernhart. Thermomechanical stress analysis of superplastic forming tools. Journal of Materials Processing Technology. 169, 281-291. 2005 [DOI]
[ACL184]N. Mébarki, D. Delagnes, P. Lamesle, F. Delmas and C. Levaillant. Relationship between microstructure and mechanical properties of a 5% Cr tempered martensitic tool steel. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 387-389, 171-175. 2004 [DOI]
[ACL185]Z. Zhang, D. Delagnes and G. Bernhart. Microstructure evolution of hot-work tool steels during tempering and definition of a kinetic law based on hardness measurements. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 380(1-2)222-230. 2004 [DOI]
[ACL186]S. Segonds, Y. Landon, M. Mousseigne and P. Lagarrigue. The Characterisation Of Dimensional Change Of Z Axis In Nc Turning . International Journal of Advanced Manufacturing Technology. 23(11-12)800-805. 2004 [DOI]
[ACL187]Y. Landon, S. Segonds, P. Lascoumes and P. Lagarrigue. Tool Positioning Error (tpe) Characterisation In Milling . International Journal of Machine Tools and Manufacture. , . 2004 [DOI]
[ACL188]T. Branza, A. Duchosal, G. Fras, F. Deschaux Beaume and P. Lours. Experimental and numerical investigation of the weld repair of superplastic forming dies. Journal of Materials Processing Technology. 155-156, 1673–1680. 2004 [DOI]
[ACL189]F. Delmas, P. Lours, M.-J. Casanove, A. Couret and A. Coujou. Quantitative TEM study of the precipitation microstructure in aluminium alloy Al(MgSiCu) 6056 T6. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 373, 80-89. 2004 [DOI]
[ACL190]G. Bernhart, F. Nazaret, A. Martinier, C.Y. Gao, D. Garriga Majo, T. Cutard and P. Lours. Design of SPF dies based on advanced material behaviour models. Materials Science Forum. 447-448, 123-130. 2004 [DOI]
[ACL191]P. Lours, Y. Le Maoult, D. Adé and B. Pieraggi. Direct Examinations of Oxide Scales Upon Cooling: a New Way to Analyse Oxide Scale Spallation. Materials Science Forum. 461-464, 639-646. 2004
[ACL192]P. Lours, H.V. Bui, A. Nafi, O. Mercier and G. Bernhart. Rapid Tooling for Injection Moulding Process . Materials Science Forum. 449-452, 789-792. 2004 [DOI]
[ACL193]P. Bruckel, P. Lamesle, P. Lours and B. Pieraggi. Isothermal Oxidation Behaviour of a Hot-Work Tool Steel. Materials Science Forum. 461-464, 831-838. 2004 [DOI]
[ACL194]C.Y. Gao, P. Lours and G. Bernhart. Damages induced by thermomechanical cycles in superplastic forming tools. Key Engineering Materials. 274-276, 93-98. 2004 [DOI]
[ACL195]T. Boulanger, A. Chrysochoos, C. Mabru and A. Galtier. Calorimetric Analysis Of Dissipative And Thermoelastic Effects Associated With The Fatigue Behavior Of Steels. International Journal of Fatigue. 26(3)221-229. 2004 [DOI]
[ACL196]Z. Zhang, Y.-H. Qi, D. Delagnes and G. Bernhart. Microstructures and properties of the tempered steel 55NiCrMoV7. Heat Treatment of Metals. 29(3)27-32. 2004
[ACL197]Z. Zhang, Y.-H. Qi, D. Delagnes and G. Bernhart. Time-Temperature-Hardness Kinetics Relation of Tempering Steels . transactions of materials and heat treatment. 25(1)41-45. 2004
[ACL198]Z. Zhang, D. Delagnes and G. Bernhart. Influence of Tempering Temperature on Cyclic Viscoplastic Behaviour of 55NiCrMoV7 Steel . transactions of materials and heat treatment. 25(5)623-626. 2004
[ACL199]F. Monies, M. Mousseigne, J.-M. Redonnet and W. Rubio. Determining a collision-free domain for the tool in five-axis machining. International Journal of Production Research. 42(21)4513-4530. 2004 [DOI]
[ACL200]Y. Qi, P. Bruckel, P. Lours and Z. Zhang. investigation of adhesion and fracture of thermally grown oxide scales by interface indentation test. transactions of materials and heat treatment. 25(5)1233-1236. 2004
[ACL201]Y. Landon, S. Segonds, M. Mousseigne and P. Lagarrigue. Correction Of Milling Tool Paths By Tool Positioning Defect (TPD) Compensation . Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 217(8)1063-1073. 2003
[ACL202]P. Bruckel, P. Lours, B. Pieraggi and P. Lamesle. in situ ESEM investigation of the oxide growth on hot work tool steel - effect of the water vapour. Materials at High Temperatures. 20(4)551-560. 2003
[ACL203]Y. Qi, P. Bruckel and P. Lours. Interfacial toughness of the nickel - nickel oxide system . Journal of Materials Science Letters. 22(5)371. 2003
[ACL204]F. Delmas, M. Vivas, P. Lours, A. Couret and A. Coujou. Straining mechanisms in aluminium alloy 6056. In-situ investigation by transmission electron microscopy. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 340, 286-291. 2003
[ACL205]M. Cheikh, S. Quilici and G. Cailletaud. Modeling of variable friction in contact with fretting. Tribology Series. 41, 153-164. 2003 [DOI]
[ACL206]D. Garcia, J.-J. Orteu and L. Penazzi. A Combined Temporal Tracking and Stereo-correlation Technique for Accurate Measurement of 3D Displacements: Application to Sheet Metal Forming. Journal of Materials Processing Technology. 125-126, 736-742. 2002 [DOI]
[ACL207]S. Claudinon, P. Lamesle, J.-J. Orteu and R. Fortunier. Continuous in-situ measurement of quenching distortions using computer vision. Journal of Materials Processing Technology. 122(1)69-81. 2002 [DOI] [HAL]
[ACL208]M. Cheikh and A. Loredo. Static reanalysis of discrete elastic structures with reflexive inverse. Applied Mathematical Modelling. 26(9)877-891. 2002
[ACL209]A. Oudin, P. Lamesle, L. Penazzi, S. Le Roux and F. Rezai-Aria. Thermomechanical fatigue behaviour and life assessment of hot work tool steels. European Structural Integrity Society. 29, 195-201. 2002 [DOI]
[ACL210]Z. Zhang, D. Delagnes and G. Bernhart. Anisothermal cyclic plasticity modelling of martensitic steels. International Journal of Fatigue. 24(6)635-648. 2002 [DOI]
[ACL211]S. Baleix, G. Bernhart and P. Lours. Oxidation and oxide spallation of heat resistant cast steels for superplastic forming dies. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 327, 155-166. 2002
[ACL212]F. Monies, J.-N. Felices, W. Rubio, J.-M. Redonnet and P. Lagarrigue. Five-axis NC milling of ruled surfaces: optimal geometry of a conical tool . International Journal of Production Research. 40(12)2901-2922. 2002
[ACL213]S. Baleix, S. Le Roux, G. Bernhart and P. Lours. Surface and image analysis of oxides grown and spalled on heat resistant cast steels exposed to thermal cycles. Journal of Materials Processing Technology. 118(1-3)321-328. 2001 [DOI]
[ACL214]M. Cheikh, P. Coorevits and A. Loredo. Modelisation of the stress vector continuity at the interface of bonded joints. International Journal of Adhesion and Adhesives. 21, 249-257. 2001
[ACL215]S. Baleix, G. Bernhart and P. Lours. Investigation on the Spallation of Oxides Grown on Thermally Cycled Heat Resistant Cast Steels. Materials Science Forum. 539, 369-372. 2001
[ACL216]P. Lours, T. Cutard, G. Bernhart and C. Levaillant. Performances of metallic and ceramic tools for superplastic forming. International Journal of Materials and Product Technology. SPM1(2)445-452. 2001
[ACL217]P. Lours, S. Baleix and G. Bernhart. Investigation on the Damages of Superplastic Forming Tools. Journal of Materials Processing Technology. 117/3(G2). 2001
[ACL218]F. Monies, W. Rubio, J.-M. Redonnet and P. Lagarrigue. Comparative study of interference caused by standard and improved positioning of a conical milling cutter working on a ruled surface. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 215, 1305-1317. 2001
[ACL219]P. Lours, S. Le Roux and G. Bernhart. Oxidation behavior of creep resistant oxide-dispersion-strengthened alloy PM2000. Journal of Advanced Materials. 34(2)11-20. 2001
[ACL220]S. Segonds, P. Lagarrigue, J.-M. Redonnet and W. Rubio. Compensation For Machining Defects Due To Spindle Dilatation . International Journal of Machine Tools and Manufacture. , . 2001
[ACL221]M. Cheikh. Reanalysis of structures with modification of the stiffness, application to the modeling of damage in unidirectiornal composites. Computers and Structures. 78(5)725-736. 2000
[ACL222]J.-M. Redonnet, W. Rubio, F. Monies and G. Dessein. Optimising tool positioning for end-mill machining of free-form surfaces on 5-axis machines for both semi-finishing and finishing. International Journal of Advanced Manufacturing Technology. 16(6)383-391. 2000
[ACL223]F. Monies, J.-M. Redonnet, W. Rubio and P. Lagarrigue. Improved positioning of a conical mill for machining ruled surfaces : application to turbine blade. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. 214, 625-634. 2000
[ACL224]G. Bernhart, G. Moulinier , O. Brucelle and D. Delagnes. High temperature low cycle fatigue behaviour of a martensitic forging tool steel. International Journal of Fatigue. 21(2)179-186. 1999 [DOI]
[ACL225]T. Cutard, E. Cailleux, P. Lours and G. Bernhart. structural and mechanical properties of refractory concrete for superplastic forming tools. Industrial Ceramics. 19(2)100. 1999
[ACL226]P. Lours, J. Alexis and G. Bernhart. Oxidation resistance of ODS alloy PM2000 from 880°C to 1400°C. Journal of Materials Science Letters. 17, 1089. 1998
[ACL227]J.-M. Redonnet, W. Rubio and G. Dessein. Side milling of ruled surfaces: Optimum positioning of the milling cutter and calculation of interference. International Journal of Advanced Manufacturing Technology. 14(7)459-465. 1998 [DOI]
[ACL228]G. Dessein, P. Lagarrigue and W. Rubio. The configuration of a machining centre and its influence on accuracy. International Journal of Advanced Manufacturing Technology. 14(1)38-42. 1998 [DOI]
[ACL229]W. Rubio, P. Lagarrigue, G. Dessein and F. Pastor. Calculation of tool paths for a torus mill on free-form surfaces on five-axis machines with detection and elimination of interference. International Journal of Advanced Manufacturing Technology. 14(1)13-20. 1998 [DOI]
[ACL230]M. Vivas, P. Lours, C. Levaillant, A. Couret, M.-J. Casanove and A. Coujou. Transmission electron microscopy study of precipitate morphology and precipitate overcoming processes in aluminium alloy 6056-T6. Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. 664, 234-236. 1997
[ACL231]M. Vivas, P. Lours, C. Levaillant, A. Couret, M.-J. Casanove and A. Coujou. Determination of precipitate strength in aluminium alloy 6056 from transmission electron microscopy data. Philosophical Magazine A. 76(5)921. 1997
[ACL232]M. Cheikh, A. Loredo and S. Aivazzaddeh. Application de la méthode de réanalyse aux assemblages collés. European Journal of Computational Mechanics. 6(4)431-449. 1997 [DOI]
[ACL233]L. Penazzi, G. Yang, C. Levaillant and A. Le Floch. assessment of thermal effect in sheet metal forming processes. International Deep Drawing Group, Iddrg 18th Biennal Congress,. , . 1996
[ACL234]M. Vivas, P. Lours, C. Levaillant, A. Couret, M.-J. Casanove and A. Coujou. some aspects of preciptation hardening in aluminium alloy 6056-T6. Materials Science Forum. 1305(217-222). 1996
[ACL235]M. Cheikh and A. Loredo. Structural reanalysis with the Moore-Penrose partial inverse. Comptes Rendus de l'Académie des Sciences, Série IIb. 323(B)83-86. 1996
[ACL236]P. Lamesle, P. Steinmetz, J. Steimetz and S. Alperine. Palladium-modified aluminide coatings-mechanisms of formation. Journal of the Electrochemical Society. 142(2)497-505. 1995 [DOI]
[ACL237]P. Lamesle and P. Steimetz. Growth mechanisms and hot corrosion-resistance of palladium modified aluminide coatings on superalloys. Materials and Manufacturing Processes. 10(5)1053-1075 . 1995 [DOI]
[ACL238]P. Lours, A. Coujou and P. Coulomb. on the deformation of <100> orientated gamma prime strengthening phase of the CMSX2 superalloy. Acta Metallurgica et Materialia. 39(8)1787. 1991
[ACL239]A. Coujou, P. Lours, N.A. Roy, D. Caillard and N. Clément. determination of the local tensile axis direction in a TEM in situ strained gamma prime single crystal - a finite element approach. Acta Metallurgica et Materialia. 38(5)825. 1990
[ACL240]P. Lours, A. Coujou and B. De Mauduit. on the high temperature stress induced spreading of SISFs in gamma prime single crystals. Philosophical Magazine A. 62(2)921. 1990
[ACL241]N. Clément, D. Caillard, P. Lours and A. Coujou. TEM in situ straining of a Ni base gamma prime single crystal - unlocking of dissociated screw dislocations at low temperature. scipta metallurgica. 23, 563. 1989
[ACL242]D. Caillard, N. Clément, A. Couret, P. Lours and A. Coujou. (111) glide in Ni3Al at room temperature. In situ observations under weak beam conditions. Philosophical Magazine Letters. 58(6)263. 1988

Article de revue avec comité de lecture non répertorié

[ACLN1]C. Le Nué, J.-M. Cloué, M.-H. Mathon, S. Puech, D. Béchet and D. Delagnes. Relationship between the yield strength-fracture toughness balance and the multiscale microstructure of a maraging stainless steel for aircraft applications. Materials Science Forum. 879, 413-418. 2017 [DOI]
[ACLN2]M. Rollin, V. Velay, L. Penazzi, T. Pottier, T. Sentenac, L. Irranzo-perez, A. Dupuy and G. Khélifati. Thermo-mechanical modeling of distortions promoted during cooling of Ti-6Al-4V part produced by superplastic forming. Materials Science Forum. 838-839, 196-201. 2016 [DOI]
[ACLN3]V. Velay, H. Matsumoto, V. Vidal, L. Penazzi, F. Nazaret, Y. Marcel and M. Bouillane. Hot forming process analysis of Ti6Al-4V alloy: experiment, behaviour modelling and Finite Element simulation. Materials Science Forum. 838-839, 183-189. 2016 [DOI]
[ACLN4]M. Chérif, C. Bois and Y. Landon. Rôle des défauts de perçage sur le comportement en matage des composites stratifiés sous sollicitation de fatigue. Revue des Composites et des Materiaux Avances. 24(4)423-434. 2014
[ACLN5]I. Souki, D. Delagnes and P. Lours. Influence of heat treatment on the fracture toughness and crack propagation in 5% Cr martensitic steel. Procedia Engineering. 10, 631-637. 2011 [DOI]
[ACLN6]D. Delagnes, F. Rézaï-aria and C. Levaillant. Influence of testing and tempering temperatures on fatigue behaviour, life and crack initiation mechanisms in a 5%Cr martensitic steel. Procedia Engineering. 2(1)427-439. 2010 [DOI]
[ACLN7]V. Velay, G. Bernhart, A. Martinier and J.-Y. Moraux. High Temperature Fatigue of SPF Die Ni-Cr-Fe Heat Resistant Nickel-Chromium Cast Steels. Key Engineering Materials. 433, 69-76. 2010 [DOI]
[ACLN8]G. Bernhart, V. Velay and P. Lours. Heat resistant Ni-Cr-Fe steels for superplastic forming dies : from material microstructure to die design. Key Engineering Materials. 433, 77-84. 2010 [DOI]
[ACLN9]L. Pin, F. Ansart, J. Fenech, P. Lours, J.-P. Bonino, J. Sniezewski and Y. Le Maoult. Advances in the field of new smart thermal barrier coatings. Advances in Science and Technology. 66, 136-141. 2010 [DOI]
[ACLN10]S. Chevalier, J.-N. Felices and W. Rubio. Modelling the Surface Generated by a Cutting Tool in Wooden Workpieces. Journal of Manufacturing Technology Research. 1, 117-136. 2009
[ACLN11]T. Kagnaya, C. Boher, M. Lazard, L. Lambert and T. Cutard. Friction at high sliding speed of WC-6Co pin versus steel disc AISI 1045 : estimation of the contact temperature. International Journal of Multiphysics. 3(141-145). 2009
[ACLN12]M. Guichon, C. Boher, B. Hassoune-rhabbour, F. Schmidt and Y. Baziard. Identification des contraintes de rupture et de cisaillement à l'interface polymère injecté-moule métallique à l'aide du test couronne. Matériaux et Techniques. 96(1-2)65-78. 2008 [DOI]
[ACLN13]P. Lamesle, M. Salem, S. Le Roux, G. Dour and F. Rezai-Aria. Oxidation and corrosion effects on thermal fatigue behaviour of hot work tool steel X38CrMoV5 (AISI H11). Materials Science Forum. 595-598 , 789-796. 2008 [DOI]
[ACLN14]Z. Ahmer, V. Velay, G. Bernhart and F. Rezai-aria. Cyclic behaviour simulation of X38CrMoV5-47HRc (AISI H11) tempered martensitic hot-work tool steel. International Journal of Microstructure and Materials Properties. 3(2/3)326-335. 2008 [DOI]
[ACLN15]V. Velay, D. Delagnes and G. Bernhart. Advances in cyclic behavior and lifetime modelling of tempered martensitic steels based on microstructural considerations. Key Engineering Materials. 378-379, 81-100. 2008 [DOI] [HAL]
[ACLN16]V. Velay, G. Bernhart and D. Delagnes. Identification and validation of a continuum damage model applied for the lifetime prediction of H11 tool steel. International Journal of Microstructure and Materials Properties. 3(2-3)282-296. 2008 [DOI]
[ACLN17]F. Rézaï-aria, C. Boher, G. Dour, P. Lamesle and S. Le Roux. Endommagement et durée de vie des outillages de mise en forme à chaud. Bulletin du cercle d'études des métaux. 17(18). 2007
[ACLN18]P. Lamesle, J. Maury and S. Le Roux. Monitoring distorsions of metallic parts during quenching. Bulletin du cercle d'études des métaux. 17(18). 2007
[ACLN19]S. Hmida-maamar, F. Schmidt, L. Robert, V. Velay and D. Mercier. Identification de paramètres de comportement de membranes en polymères durant le procédé de soufflage. Matériaux et Techniques. 94(5)371-378. 2006 [DOI]
[ACLN20]S. Claudinon, R. Fortunier , P. Lamesle and J.-J. Orteu. Suivi continu par vision de la distorsion d'outils au traitement thermique. Bulletin du cercle d'études des métaux. 16(17)22.1-22.7. 1998

Articles dans des revues sans comité de lecture

[ASCL1]H.L. Dorothy , P. Longère and A. Dragon. Coupled ASB-and-microvoiding-assisted Dynamic Ductile Failure. Procedia Engineering. 197, 60-68. 2017 [DOI]
[ASCL2]H.L. Dorothy , P. Longère and A. Dragon. Modelling of high strain rate failure under ASB and microvoiding. Procedia Engineering. 173, 593-600. 2017 [DOI]

Communication invitée dans un congrès national ou international

[INV1]N. Saintier, A. Hor, C. Robert, R. Guerchais, T. Palin-luc and F. Morel. Calculs de microstructures en fatigue : pourquoi, comment et avec quels résultats ?. Colloque National MECAMAT Aussois 2017 : Fatigue des structures et des matériaux Invited lecture 2017
[INV2]Y. Landon. Manufacturing’21 : Expériences de fédération des activités de recherche en fabrication. 13ème Colloque National AIP-PRIMECA – Démarche et Innovation dans la Conception et la Production des Systèmes Intégrés Invited plenary lecture 2012
[INV3]G. Bernhart, V. Velay and P. Lours. Heat Resistant Ni-Cr-Fe Steels for Superplastic Forming Dies : from material microstructure to die design. ICSAM 2009, 10th International Conference on Superplasticity in Advanced materials, Seattle, USA Invited plenary lecture 2009
[INV4]F. Medjedoub, G. Dour, S. Le Roux, P. Lamesle, M. Salem and F. Rézaï-aria. Experimental conditions and environment effects on thermal fatigue damage accumulation and life of die-casting steel X38CrMoV5 (AISI H11). Proceedings of 7th International Tooling Conference Invited lecture p.461-469 2006
[INV5]P. Lours, Y. Qi, Y. Le Maoult and B. Pieraggi. In situ and ex situ investigation of the spallation of thermally grown oxides . THERMEC 2006 - PROCEEDINGS INTERNATIONAL CONFERENCE ON PROCESSING AND MANUFACTURING OF ADVANCED MATERIALS, VANCOUVER, CANADA, JULY 2006 published in Materials Science Forum Invited lecture 2006
[INV6]F. Rézaï-aria, F. Medjedoub, G. Dour and S. Le Roux. Some aspects of thermal fatigue of metallic tools. Abrasion Conference 2005 Invited lecture 2005
[INV7]P. Lours, Y. Le Maoult, D. Adé and B. pieraggi. Direct examinations of oxide scales upon cooling: a new way to analyse oxide scale spallation . 6TH INTERNATIONAL CONFERENCE ON HIGH TEMPERATURE CORROSION AND PROTECTION OF MATERIALS - Les Embiez, France, May 2004 Invited keynote lecture 2004
[INV8]P. Lours, H.V. bui, A. Nafi, O. Mercier and G. Bernhart. Rapid tooling for injection moulding process . ISAEM 2003 - PROCEEDINGS INTERNATIONAL SYMPOSIUM ON ADVANCED ENGINEERING MATERIALS , JEJU, KOREA, NOVEMBER 2003 published in ”Materials Science Forum” Invited lecture 2003
[INV9]P. Lours, T. Cutard, G. Bernhart and C. Levaillant. Performances of metallic and ceramic tools for superplastic forming tools . ISAEM 2000 - PROCEEDINGS INTERNATIONAL SYMPOSIUM ON ADVANCED ENGINEERING MATERIALS , GUILIN, PEOPLE REPUBLIC OF CHINA, OCTOBER 2000, SPM1, 2, 445, 2001 ”Special Issue: Int Journal of Materi Invited lecture 2001
[INV10]P. Lours, S. Baleix and G. Bernhart. Investigation on the damages of superplastic forming tools. THERMEC 2000 - PROCEEDINGS INTERNATIONAL CONFERENCE ON PROCESSING AND MANUFACTURING OF ADVANCED MATERIALS, LAS VEGAS, USA, DECEMBER 2000 Invited lecture 2000

Communication avec actes dans un congrès international ou national

[ACT1]H.L. Dorothy and P. Longère. Modélisation isotrope vs. anisotrope du processus de dégradation dynamique par cisaillement adiabatique. Proceedings of CSMA2017, 13ème Colloque National en Calcul des Structures, Giens (France), 15-19 mai 2017 2017
[ACT2]Q. Sirvin, V. Velay, R. Bonnaire and L. Penazzi. Mechanical Behavior And Modelisation Of Ti-6Al-4V Titanium Sheet Under Hot Stamping Conditions. Proceedings of ESAFORM 2017 2017
[ACT3]C. Melgar, M. Gomez-jimenez, L. Cot, S. Dejean, C. Mabru and J. Martinez-vega. Paris law parameter identification based on the Extended Kalman Filter. Proceedings of MATEC Web Conf. Volume 83, 2016 CSNDD 2016 - International Conference on Structural Nonlinear Dynamics and Diagnosis p. 03003 2016 [DOI]
[ACT4]F. Bruno, I. Thabet, J. Huez, A. Hor, B. Malard, N. Ratel-ramond, G. Chevalier, V. Baylac and C. Estournès. Evaluation des contraintes résiduelles dans les alliages de Ti-6Al-4V mis en forme par SLM et « Spark Plasma Sintering - SPS ». Proceedings of SF2M, Journées Annuelles (JA 2016), Matériaux pour le domaine aérospatial : de l’innovation dans l’air, Albi, France 2016
[ACT5]S. Naanani, A. Couret, J.-P. Monchoux, M. Hantcherli, C. Mabru and A. Hor. Etude du comportement à hautes températures d’un alliage TiAl densifié par frittage flash. Proceedings of SF2M, Journées Annuelles (JA 2016), Matériaux pour le domaine aérospatial : de l’innovation dans l’air, Albi, France 2016
[ACT6]R. Gomes, C. Boher and L. Penazzi. Hot blanking tool wear assessment. Proceedings of 10th TOOL Conference 2016 - TOOL 2016 p.239-247 2016
[ACT7]E. Cabrol, C. Boher, V. Vidal, F. Rézaï-aria and F. Touratier. Wear mechanisms of hardfaced aeronautical high temperature forging tools. Proceedings of ASMET - TOOL STEEL 2016 2016
[ACT8]V. Bonnot, Y. Landon and S. Segonds. Tool/Material Interferences Sensibility to Process and Tool Parameters in Vibration- Assisted Drilling. Proceedings of International Joint Conference on Mechanics, Design Engineering & Advanced Manufacturing JCM, Catania, Italy 2016
[ACT9]P. Longère, A. Dragon and H.L. Dorothy . Modelling of shear failure caused by adiabatic shear banding and subsequent microvoiding. Proceedings of ICTAM 2016, 24th International Congress of Theoretical and Applied Mechanics, Montréal (Canada), 21-26 august 2016 2016
[ACT10]S. Arki, S. Marguet, J.-M. Redonnet, J.-F. Ferrero, P. Navarro and A. Aury. Semi-continous approach for the modelling of complex shaped thick composite parts. Proceedings of 2nd International conference on mechanics of composites p.176 2016 [DOI]
[ACT11]R. Gomes, C. Boher and L. Penazzi. Hot blanking tools thermo-mechanical loading simulations. Proceedings of NUMIFORM 2016 p.3 2016
[ACT12]M. Harzallah, T. Pottier, J. Senatore, M. Mousseigne, G. Germain and Y. Landon. A New Behavior Model for Better Understanding of Titanium alloys Ti-6Al-4V Chip Formation in Orthogonal Cutting. Proceedings of ESAFORM 2016 2016
[ACT13]A. Zouaghi, V. Velay, A. Soveja, F. Rézaï-aria, T. Pottier and M. Cheikh. Multiscale Modelling of the Surface Behaviour of AISI H11 Tool Steels. Proceedings of 10th TOOL Conference 2016 - TOOL 2016 2016
[ACT14]U. Kus, J. Huez, D. Delagnes, G. Chevallier and C. Estournes. Relationship between microstructure and tensile properties of a Ti-6Al-4V produced by spark plasma sintering. Proceedings of 13th World conference on Titanium, San Diego, USA August 16-20, 2015 p.651-656 2016 [DOI]
[ACT15]M. Ladonne, M. Chérif, Y. Landon, J.-Y. K'nevez, O. Cahuc and C. De Castelbajac. A Dynamic Modelling of Vibrations Assisted Drilling. Proceedings of Productica 2015, Romania, May 29, 2015 2015
[ACT16]A. Hor, N. Saintier, C. Robert, T. Palin-luc and F. Morel. Utilisation des statistiques des extrêmes pour l’analyse de la durée de vie en fatigue multiaxiale des polycristaux. Proceedings of SF2M, 34èmes Journées de Printemps : Microstructure-procédés-propriétés en fatigue, Paris, France 2015
[ACT17]H. Matsumoto, V. Velay and A. Chiba. Superplasticity of the Ultrafine‐Grained Ti‐6Al‐4V Alloy with a Metastable α‐Single Phase Microstructure. Proceedings of 13th World Conference on Titanium p.789-792 2015 [DOI]
[ACT18]J. Le Dref, Y. Landon and G. Dessein. Thrust force and torque model applied to the vibration assisted drilling of Aluminium 7010. Proceedings of 32nd Machinery Vibration CMVA Annual Seminar – 4th International Congress on Engineering of Industrial Risks, Montreal, Canada, October 29-31, 2014 2014
[ACT19]J. Le Dref, Y. Landon, G. Dessein and C. Espinosa. Contribution to understanding and modelizing vibration assisted drilling. Proceedings of 4th ICEIR Int. Congress on Engineering of Industrial Risks & 32nd CMVA Annual Seminar on Machinery Vibration 2014
[ACT20]M. Ladonne, Y. Landon, M. Chérif, J.-Y. K'nevez, O. Cahuc and C. De Castelbajac. A Dynamic Cutting Forces Model of Vibrations Assisted Drilling. Proceedings of 32nd Machinery Vibration CMVA Annual Seminar – 4th International Congress on Engineering of Industrial Risks, Montreal, Canada, October 29-31, 2014 2014
[ACT21]A. Zouaghi, V. Velay, A. Soveja and F. Rézaï-aria. A NUMERICAL INVESTIGATION ON THE HETEROGENEOUS AND ANISOTROPIC MECHANICAL BEHAVIOUR OF AISI H11 STEEL USING VARIOUS STRESS-STRAIN FORMULATIONS: A MULTI-SCALE APPROACH. Proceedings of 11th World Congress on Computational Mechanics (WCCM XI) 2014
[ACT22]E. Copin, Y. Le Maoult, T. Sentenac, F. Blas, T.H.G. Tran and P. Lours. Comparison of IR Thermography and Reflectance-Enhanced Photoluminescence for early Quantitative Diagnostic of Thermal Barrier Coatings Spallation. Proceedings of 12th International Conference on Quantitative InfraRed Thermography (QIRT 2014), Bordeaux, 07 - 11 July 2014 2014
[ACT23]E. Cabrol, C. Boher, V. Vidal, F. Touratier and F. Rezai-aria. A wear damage assessment of high temperature forging. Proceedings of Proceedings of 6th ICTMP International Conference on Tribology in Manufacturing Processes & Joining by Plastic Deformation, June 22–24, Darmstadt, Germany, Editors : P.Groche, Publisher: Trans Tech p.103-110 2014
[ACT24]T. Sultan, P. Gilles, G. Cohen, F. Cenac and W. Rubio. Profile incision modeling in Abrasive waterjet milling of Titanium alloys Ti6Al4V. Proceedings of Integrated Design and Manufacturing in Mechanical Engineering 2014
[ACT25]P. Rahmé, Y. Landon, R. Piquet, F. Lachaud and P. Lagarrigue. Drilling of thick composite structures with pilot hole using a twist drill. Proceedings of 16th European Conference on Composite Materials (ECCM16), Seville, Spain, June 22-26, 2014 2014
[ACT26]P. Rahmé, Y. Landon, R. Piquet, F. Lachaud and P. Lagarrigue. Analytical model for drilling thick composite structures with pilot hole using a twist drill. Proceedings of Joint Conference on Mechanical, Design Engineering & Advanced Manufacturing, Toulouse, France, June 18-20, 2014 2014
[ACT27]A. Zouaghi, V. Velay, A. Soveja and F. Rezai-aria. Multi-scale modelling of AISI H11 martensitic tool steel surface anisotropic mechanical behaviour. Proceedings of Fatigue Design & Material Defects 2014 [DOI]
[ACT28]P.A. Rey, K. Moussaoui, J. Senatore and Y. Landon. Modelling of chip geometry in orbital drilling. Proceedings of Joint Conference on Mechanical, Design Engineering & Advanced Manufacturing, Toulouse, France, June 18-20, 2014 p.502-508 2014
[ACT29]J. Le Dref, Y. Landon, G. Dessein and F. Blanchet. Thrust force and torque model applied to the vibratory drilling process. Proceedings of Joint Conference on Mechanical, Design Engineering & Advanced Manufacturing, Toulouse, France, June 18-20, 2014 2014
[ACT30]E. Copin, T. Sentenac, Y. Le Maoult, F. Blas, F. Ansart, V. Vidal and P. Lours. Feasibility of luminescent multilayer sol-gel thermal barrier coating manufacturing for future applications in through-thickness temperature gradient sensing.. Proceedings of 41st International Conference on Metallurgical Coatings and Thin Film San Diego California April 2014 2014
[ACT31]F. Blas, F. Ansart, P. Lours, J.-P. Bonino, S. Duluard, V. Vidal and L. Pin. Microstructural control of new generation thermal barrier coatings via a sol-gel route : cyclic oxidation behaviour. Proceedings of Thermal Barrier Coatings IV - An ECI Conference Series - Irsee - Germany - June 2014 2014
[ACT32]E. Copin, T. Sentenac, Y. Le Maoult, F. Blas, F. Ansart, V. Vidal and P. Lours. Feasibility of luminescent multilayer sol-gel thermal barrier coating manufacturing for future applications in through-thickness temperature gradient sensing. Proceedings of 41st International Conference on Metallurgical Coatings and Thin Film San Diego California April 2014 2014
[ACT33]P. Le Baillif, P. Lamesle, D. Delagnes, V. Velay, C. Dumont and F. Rézaï-aria. Influence of the quenching rate and step-wise cooling temperatures on microstructural and tensile properties of PER72 R © Ni-based superalloy. Proceedings of SUPERALLOYS 2014 - 2nd European Symposium on Superalloys and their Applications 2014 [DOI]
[ACT34]M. Ladonne, Y. Landon, O. Cahuc, M. Chérif, J.-Y. K'nevez and C. De Castelbajac. Dynamic Modeling of Vibrations Assisted Drilling. Proceedings of 5th International Conference on Structural Analysis of Advanced Materials (ICSAAM), Island of Kos, Greece, September 23-26, 2013 2013
[ACT35]S. Djebali, S. Segonds, J.-M. Redonnet and W. Rubio. Using Clarke and Wright's Algorithm to Minimize the Machining Time of Free-Form Surfaces in 3-Axis Milling. Proceedings of World Congress on Engineering 2013
[ACT36]N. Wojtowicz, I. Danis, F. Monies, P. Lamesle and R. Chieragatti. The influence of cutting conditions on surface integrity of a wrought magnesium alloy. Proceedings of The Manufacturing Engineering Society International Conference, MESIC 2013 p.20-28 2013 [DOI]
[ACT37]I. Danis, N. Wojtowicz, F. Monies, P. Lamesle and P. Lagarrigue. Cutting Conditions and Surface Integrity During Dry Plunge-milling of a Wrought Magnesium Alloy. Proceedings of The Manufacturing Engineering Society International Conference, MESIC 2013 p.36-44 2013 [DOI]
[ACT38]C. Bellot, D. Delagnes, P. Lamesle and D. Béchet. Developing cementite-free martensitic steels: a relevant route to obtain high strength-high toughness steels for tools applications. Proceedings of 9th international tooling conference p.241-247 2012
[ACT39]F. Abevi, M. Chaussumier and A. Daidié. Répartition de charge dans une vis à rouleaux. Proceedings of 13ème Colloque National Mont-Dore 2012
[ACT40]J. Senatore, F. Monies and W. Rubio. Analyse de la vrille des surfaces réglées, application à l'usinage par bande. Proceedings of AIP Priméca, Mont Dore 2012
[ACT41]K. Pinho-faria, C. Boher and C. Scandian. Effect of molybdenum and chromium contents on sliding wear of high-chromium white cast iron at high temperature. Proceedings of TribBR-2010 First INternational brazilian conference on Tribology 24-26th November 2010 2012 [DOI]
[ACT42]P. Gilles, G. Cohen, F. Monies and W. Rubio. Positionnement d'outil torique avec équilibrage de l'effort de coupe transversal . Proceedings of AIP Priméca, Mont Dore 2012
[ACT43]L. Benezech, Y. Landon and W. Rubio. Study of manufacturing defects and tool geometry optimisation for multi-material stack drilling. Proceedings of 4th International Conference on Structural Analysis of Advanced Materials (ICSAAM), Sinaia, Romania, September 7-10, 2011 2011
[ACT44]F. Abevi, M. Chaussumier, A. Daidié and F. Bouillot. Comprehensive study of a normal elastic contact in a satellite roller screws device under static loading. Proceedings of 4th International Congress CMSM’2011, Sousse, Tunisia, May 30 – June 1 2011
[ACT45]I. Souki, D. Delagnes and P. Lours. Influence of heat treatment on the fracture toughness and crack propagation in 5% Cr martensitic steel. Proceedings of International Conference on the Mechanical Behaviour of Materials ICM- Lago di Como, Italy 2011 2011
[ACT46]V. Vidal, Y. Balcaen, F. Pettinar-strumel, J. Douin, P. Lours, V. Velay and L. Robert. Experimental study of the deformation mechanisms in textured pure alpha-titanium sheets. Proceedings of Proceedings of the 12th World Congresss on Titanium Beijing China 2011
[ACT47]Y. Balcaen, V. Vidal, V. Velay, L. Robert, F. Pettinari-strumel, J. Douin and P. Lours. Comparative Study, in pure titanium sheet, of the microstructural evolution induced by incremental forming process and plane strain tensile tests. Proceedings of Proceedings of the 12th World Congresss on Titanium Beijing China 2011
[ACT48]K. Ben Slima, L. Penazzi, C. Mabru, F. Ronde-oustau and F. Rézaï-aria. A new method for advanced virtual design of stamping tools for automotive industry: application to nodular cast iron EN-GJS-600-3 . Proceedings of The 14th International Conference on Material Forming - Esaform 2011 p.1713-1720 2011 [DOI] [OATAO]
[ACT49]I. Souki, D. Delagnes and P. Lours. Influence of heat treatment on the fracture toughness and crack propagation in 5% Cr martensitic steel. Proceedings of ICM 11 - 11th International conference on the mechanical behavior of materials - Como Italy 2011 [DOI]
[ACT50]L. Pin, F. Ansart, J.-P. Bonino, Y. Le Maoult, V. Vidal and P. Lours. Processing, repairing and cyclic oxidation behaviour of sol gel thermal barrier coatings. Proceedings of ICMCTF - 38th International Conference on Metallurgical Coatings and Thin Films - San Diego USA 2011 [DOI]
[ACT51]R. Chieragatti, C. Espinosa, J.-L. Lacome, J. Limido, C. Mabru and M. Salaün. Détermination d’un kt local associé à la rugosité de surface; influence sur la tenue en fatigue. Proceedings of 29ème Journées de Printemps de la SF2M : Influence des procédés sur la tenue en fatigue, Rôle des défauts - Paris (France), Mai 2010 [OATAO]
[ACT52]F. Abevi, M. Chaussumier and A. Daidié. Contribution à l’étude du contact normal élastique dans un système de vis à rouleaux satellites d’actionneurs aéronautiques sous un chargement statique. Proceedings of Journées Internationales Francophones De Tribologie, Albi (France), 27-28 Mai 2010
[ACT53]L. Pin, F. Ansart, P. Lours, J. Sniezewski, J. Fenech, J.-P. Bonino and Y. Le Maoult. Caractérisation du comportement en oxydation cyclique de barrières thermiques élaborées par voie sol-gel. Proceedings of Matériaux 2010 - Nantes, FRANCE 2010
[ACT54]I. Souki, D. Delagnes and P. Lours. Influence du traitement thermique sur la ténacité et la propagation de fissures pour un acier à 5% Cr. Proceedings of Matériaux 2010 - Nantes, FRANCE 2010
[ACT55]M. Chaussumier, M. Shahzad, C. Mabru, R. Chieragatti and F. Rézaï-aria. Modélisation de la multi-fissuration d’un alliage d’aluminium 7010 traité par oxydation anodique chromique. Proceedings of 29èmes Journées De Printemps De La Sf2m, ”influence Des Procédés Sur La Tenue En Fatigue, Rôle Des Défauts” p.147-154 2010 [OATAO]
[ACT56]J. Pancrace, P. Lamesle, E. Rodier, F. Schmidt, Y. Le Maoult and F. Berthet. 2209 - Evolution de la microstructure et influence de la pollution atmosphérique lors de la mise en oeuvre d'une résine thermodurcissable . Proceedings of Matériaux 2010 p.9p 2010
[ACT57]M. Shah, C. Mabru and F. Rézaï-aria. Investigation Of Crack Propagation In X38crmov5 (aisi H11) Tool Steel At Elevated Temperatures . Proceedings of 10th International Fatigue Conference p.2045-2054 2010 [DOI] [OATAO]
[ACT58]M. Shahzad, M. Chaussumier, R. Chieragatti, C. Mabru and F. Rézaï-aria. Influence of anodizing process on fatigue life of machined aluminium alloy . Proceedings of 10th International Fatigue Conference p.1015-1024 2010 [DOI] [OATAO]
[ACT59]M. Chaussumier, M. Shahzad, C. Mabru, R. Chieragatti and F. Rézaï-aria. A fatigue multi-site cracks model using coalescence, short and long crack growth laws, for anodized aluminum alloys. Proceedings of 10th International Fatigue Conference p.995-1004 2010 [DOI] [OATAO]
[ACT60]N. Decultot, L. Robert, V. Velay and G. Bernhart. Single point incremental sheet forming investigated by in-process 3D digital image correlation. Proceedings of 14th International Conference on Experimental Mechanics (ICEM'14), Poitiers (France), 4-9 July 2010 p.1151-1154 2010 [DOI]
[ACT61]L. Pin, F. Ansart, J. Fenech, P. Lours, J.-P. Bonino, J. Sniezewski and Y. Le Maoult. Advances in the field of new smart thermal barrier coatings . Proceedings of CIMTECH Venezzia 2010 2010
[ACT62]F. Taina, M. Pasqualon, V. Velay, D. Delagnes and P. Lours. Effect of the LCF loading cycle characteristics on the fatigue life of Inconel 718 at high temperature. Proceedings of 7th International symposium on superalloy 718 and derivatives - Pittsburgh, USA 2010
[ACT63]J. Sniezewski, Y. Le Maoult, P. Lours, L. Pin, V. Minvie Bekale, D. Monceau, D. Oquab, J. Fenech, F. Ansart and J.-P. Bonino. Sol-gel thermal barrier coatings : optimization of the manufacturing route and durability under cyclic oxidation. Proceedings of 37th International Conference on Metallurgical Coatings & Thin films, ICMCTF 2010 San Diego (USA), April 2010 2010
[ACT64]V. Velay, G. Bernhart, A. Martinier and J.Y. Moraux. High temperature fatigue of spf die ni-cr-fe heat resistant nickel-chromium cast steels. Proceedings of ICSAM 2009 - 10th International Conference On Superplasticity In Advanced Materials - Seattle, USA p.69-76 2010 [DOI]
[ACT65]J. Sniezewski, Y. Le Maoult, P. Lours, L. Pin, V. Minvie Bekale, D. Monceau, D. Oquab, J. Fenech, F. Ansart and J.-P. Bonino. Sol-gel thermal barrier coatings : optimization of the manufacturing route and durability under cyclic oxidation. Proceedings of ICMCTF 2010 - 37th International Conference on Metallurgical Coatings and Thin Films - San Diego, USA 2010 [DOI]
[ACT66]X. Pessoles, Y. Landon, W. Rubio and J.-M. Redonnet. Dynamic model of CNC milling machines. Proceedings of 3rd International Conference on Structural Analysis of Advanced Materials (ICSAAM), Tarbes, France, September 7-10, 2009 2009
[ACT67]S. Ramde, L. Penazzi and F. Ronde-oustau. Optimisation géométrique des outillages de découpe. Proceedings of Cfm'09 - Marseille 2009
[ACT68]J. Limido, M. Suraratchaï, C. Mabru, C. Espinosa, M. Salaün, R. Chieragatti and V. Vergnes. Machining parameters effects on surface and fatigue life of Aluminum alloy aeronautical parts. Proceedings of EUCASS 2009 - 3rd European Conference for Aero-Space Sciences - Versailles (France), Juillet 2009
[ACT69]M. Salem, P. Lamesle, H. Laribou, S. Le Roux, G. Dour and F. Rézaï-aria. Oxidation and corrosion effects on non-isothermal fatigue of hot work tool steel X38CrMoV5 (AISI H11). Proceedings of 8th International Tooling Conference p.437-445 2009
[ACT70]J. Limido, C. Espinosa, M. Salaün, C. Mabru and R. Chiergatti. High speed machining modelling : SPH method capabilities. Proceedings of 4th SPHERIC Workshop, mai 2009, Nantes (FR) 2009
[ACT71]S. Chevalier, J.-N. Felices and W. Rubio. Detection and reduction of zones of burning in 5-axis machining of wooden parts. Proceedings of International Conference on Structural Analysis of Advanced Materials 2009
[ACT72]G. Bernhart, V. Velay and P. Lours. Heat resistant Ni-Cr-Fe steels for superplastic forming dies : from material microstructure to die design. Proceedings of ICSAM 2009 - 10th International Conference on Superplasticity in Advanced Materials - Seattle, USA 2009 [DOI]
[ACT73]J. Sniezewski, V. Vidal, P. Lours and Y. Le Maoult. Thermal barrier coatings adherence and spallation : interfacial indentation resistance and cyclic oxidation behaviour under thermal gradient. Proceedings of ICMCTF 2009 - 36th International Conference on Metallurgical Coatings and Thin Films - San Diego USA 2009 [DOI]
[ACT74]M. Shah, C. Mabru, C. Boher, S. Le Roux and F. Rézaï-aria. Crack propagation in X38CrMoV5 (AISI H11) tool steel. Proceedings of 8th International Tooling Conference p.83-94 2009 [OATAO]
[ACT75]Y. Goueffon, M. Monjauze, C. Mabru, L. Arurault, C. Tonon and P. Guigue. Study of degradation mechanisms of black anodic films in simulated space environment. Proceedings of 11th International Symposium On Materials In Space Environment 2009 [OATAO]
[ACT76]M. Chaussumier, M. Shahzad, C. Mabru, R. Chieragatti and F. Rézaï-aria. Influence du décapage sur la tenue en fatigue de l'alliage al7010-t7451 traité par oxydation anodique chromique. Proceedings of Cfm 2009 19ème Congrès Français De Mécanique 2009 [OATAO]
[ACT77]J. Limido, C. Espinosa, M. Salaün, J.-L. Lacome, C. Mabru and R. Chieragatti. Metal cutting analysis : SPH approach. Proceedings of JSTMM08 - 6th Scientific and Technical Symposium on Manufacturing and Materials - Monastir (Tunisie), Novembre 2008 [OATAO]
[ACT78]P. Rahmé, Y. Landon, P. Lagarrigue, R. Piquet, F. Lachaud, B. Marguet, J. Bouriquet and C. Leroy. Analytical and numerical models for drilling of composite materials using twist drill. Proceedings of 7th International Conference on Integrated Design and Manufacturing in Mechanical Engineering (IDMME 2008) – Virtual Concept 2008, Beijing, China, October 8-10, 2008 2008
[ACT79]C. Dessain, P. Hein, J. Wilsius, L. Penazzi, C. Boher and J. Weikert. Experimental investigation of friction and wear in hot stamping of usibor 1500p. Proceedings of 1rst International Conference On Hot Sheet Metal Forming Of High Performance Steel, Chs2 2008
[ACT80]P. Rahmé, Y. Landon, P. Lagarrigue, R. Piquet, F. Lachaud, B. Marguet, J. Bouriquet and C. Leroy. Chisel Edge Effect on Delamination when Drilling Thick Composite Materials with a Twist Drill. Proceedings of Aerospace Manufacturing and Automated Fastening (AMAF) SAE International Conference, Detroit, MI, USA, April 14–17, 2008 2008
[ACT81]C. Espinosa, J.-L. Lacome, J. Limido, M. Salaün, C. Mabru and R. Chieragatti. Modeling High Speed Machining with the SPH Method. Proceedings of 10th International LS-DYNA(R) Users Conference, June 2008, Dearborn (USA) 2008
[ACT82]G. Kaza, C. Boher, G. Dour, L. Penazzi and T. Loulou. Contribution to the determination of the thermal contact resistance : algorithm of evaluation of the number of asperities involved in the contact, . Proceedings of Nordtrib 2008 - 13th Nordic Symposium On Tribology 2008
[ACT83]N. Decultot, V. Velay, L. Robert, G. Bernhart and E. Massoni. Behaviour modelling of aluminium alloy sheet for single point incremental forming. Proceedings of 11th Esaform Conference On Material Forming, Lyon (france) p.1151-1154 2008 [DOI]
[ACT84]N. Decultot, G. Bernhart, L. Robert, V. Velay and E. Massoni. Etude du comportement de tôle d’aluminium embouties par formage incrémental. Proceedings of Colloque MECAMAT 2008, Aussois, France, Janvier 2008
[ACT85]M. Suraratchai, J. Limido, C. Mabru and R. Chieragatti. Determination of a local stress concentration induced by machining and its effect on fatigue life of an aluminum alloy. Proceedings of JSTMM'08 - Sixth Scientific and Technical Symposium on Manufacturing and Materials 2008 [OATAO]
[ACT86]M. Shah, C. Mabru, C. Boher, S. Le Roux and F. Rézaï-aria. Crack Propagation In Tool Steel X38CrMoV5 (aisi H11) In Set Specimens. Proceedings of 27th Spring Meeting On Fatigue And Plasticity p.746-749 2008 [DOI] [OATAO]
[ACT87]V. Velay, T. Cutard and N. Guégan. Thermal behaviour modelling of superplastic forming tools. Proceedings of EuroSPF2008, 7th European Conference on Superplastic Forming, Carcassone (France) 2008
[ACT88]T. Kagnaya, C. Boher, L. Lambert, M. Lazard and T. Cutard. Friction at high sliding speed of WC/Co pin versus steel disc: estimation of the contact temperature. Proceedings of ACE-X International Conference, Barcelona, 2008
[ACT89]J. Sniezewski, Y. Le Maoult and P. Lours. In situ thermal gradient controlled investigation of spallation – Experimental design and preliminary results. Proceedings of 7th International Conference on High Temperature Corrosion and Protection of Materials, Les Embiez, France, May 2008 2008
[ACT90]J. Limido, M. Suraratchai, C. Mabru, C. Espinosa, M. Salaün and R. Chieragatti. Machining parameters effects on fatigue life of aluminum alloy aeronautical parts. Proceedings of Fatigue Design 2007 - International Conference on the respective input of the numerical simulation and the experimental approach in fatigue design - Senlis (France), Novembre 2007 [OATAO]
[ACT91]L. Robert, S. Hmida-maamar, V. Velay and F. Schmidt. Determination of the elongational properties of polymers using a mixed numerical-experimental method. Proceedings of International Conference on Experimental Mechanics (ICEM'13), Alexandroupolis, Greece p.667-668 2007 [DOI]
[ACT92]M. Bordival, F. Schmidt, Y. Le Maoult and V. Velay. Simulation of the two stages Stretch-Blow Molding Process. Proceedings of 9th International Conference on Numerical Methods in Industrial Forming Processes 2007
[ACT93]L. Penazzi, F. Baillon and E. Loubignac. Campus : retour d'expériences sur une application de la plate-forme, moodle à l'apprentissage en mécanique. Proceedings of Colloque Moodlemoot, Castres, 14-15 June 2007. 2007
[ACT94]P. Lamesle, J. Maury and S. Le Roux. Monitoring distorsions of metallic parts during quenching. Proceedings of 5th International Conference and European Conference on Heat Treatment 2007 p.191-198 2007
[ACT95]V. Velay, L. Robert, F. Schmidt, S. Hmida and T. Vallet. Behaviour model identification based on inverse modeling and using optical full field measurements (offm): application on rubber and steel. Proceedings of 10th Esaform Conference On Material Forming p.33-38 2007 [DOI]
[ACT96]Y. Goueffon, C. Mabru, L. Arurault, P. Guigue and C. Tonon. Problématique d'adhérence des revêtements anodisés inorganiques noirs pour applications spatiales. Proceedings of 14e Journées D'étude Sur L'adhésion 2007 [OATAO]
[ACT97]P. Rahmé, Y. Landon, P. Lagarrigue, R. Piquet, F. Lachaud, B. Marguet, J. Bouriquet and C. Leroy. Drilling of thick composite structures – State of the art. Proceedings of Aerospace Manufacturing and Automated Fastening (AMAF) SAE International Conference, Toulouse, France, September 12–14, 2006 2006
[ACT98]V. Velay, G. Bernhart and D. Delagnes. Identification and validation of a continuum damage model applied for the lifetime prediction of h11 tool steel. Proceedings of 7th International Tools 06 Conference, Torino Italie 2006 [DOI]
[ACT99]J. Sniezewski, P. Lours and Y. Le Maoult. Etude in situ de l’écaillage des couches d’oxyde de l’alliage PM2000 . Proceedings of Actes du congrès Matériaux 2006, Dijon France, 13-17 Novembre 2006 2006
[ACT100]J. Rishmany, L. Renault, C. Mabru, R. Chieragatti and F. Rézaï-aria. Static and dynamic behaviour of a 3d periodic structure. Proceedings of 16th European Conference Of Fracture : Ecf 16 Failure Analysis Of Nano And Engineering Materials And Structures 2006 [DOI] [OATAO]
[ACT101]E. Herny, P. Lours, P. Lagain, J.-M. Cloué, M.-C. Lafont and E. Andrieu. Evolution of the mechanical properties of two precipitation hardening stainless steels after ageing at 400°C : comparison between 15-5PH and 13-8PH . Proceedings of Proceedings of the 3rd International Conference on Use of Steels, Instituto Argentina de Siderurgia (IAS), San Nicolas, Argentina, November 7-10th, 2006 2006
[ACT102]G. Pellegrino, F. Chaffotte, J.F. Douce, S. Denis, J.P. Bellot and P. Lamesle. Efficient numerical simulation techniques for high pressure gas quenching. Proceedings of 23rd ASM-Heat-Treating-Society Conference, Pittsburgh, PA, SEP 25-28, 2005 p.320-328 2006
[ACT103]Z. Ahmer, V. Velay, G. Bernhart and F. Rezaï-aria. Cyclic behaviour simulation of x38crmov5-47hrc (aisi h11)-tempered martensitic hot-work tool steel . Proceedings of Proceedings Of 7th International Tools 06 Conference, Torino Italie p.326-335 2006 [DOI]
[ACT104]M. Guichon, C. Boher and F. Schmidt. An Understanding of Polymer/Mold Contact during Injection Moulding Cycle. Proceedings of PPS-2005: America Regional Meeting 2005
[ACT105]M. Suraratchai, C. Mabru, C. Espinosa and R. Chieragatti. Rôle de la rugosité d'une surface usinée sur la fatigue d'un alliage d'aluminium aéronautique. Proceedings of 24èmes Journées de Printemps SF2M 2005
[ACT106]M. Suraratchai, C. Mabru, R. Chieragatti and F. Rézaï-aria. Influence de gammes d'usinage sur la tenue en fatigue d'un alliage léger aéronautique. Proceedings of Cfm 2005 : 17ème Congrès Français De Mécanique 2005 [OATAO]
[ACT107]E. Herny, P. Lours, J.-M. Cloué, P. Lagain, S. Pérusin, E. Jourdain and E. Andrieu. Local mechanical and microstructural characterization of EB welded 15-5 PH stainless steel . Proceedings of Proceedings of AIM conference, Roma, Italia, November 2005 2005
[ACT108]A. Duchosal, T. Branza, C. Bordreuil, F. Deschaux Beaume, P. Lours and G. Fras. Macro-micro transition to model cracking phenomena during multipasses welding processes. Proceedings of Proceedings of the eigth International Conference on Computational Plasticity, COMPLAS VIII, Ed. by E. Oñate & DRJ Owen, Barcelona, Spain, September 2005 2005
[ACT109]Y. Le Maoult, P. Lours and B. Pieraggi. In situ investigation of the spallation of oxide scales grown on ODS alloy PM2000. Proceedings of 2005
[ACT110]T. Branza, A. Duchosal, C. Bordreuil, F. Deschaux Beaume, G. Fras and P. Lours. Influence of the welding processing on weld repair quality of SPF tools. Proceedings of Proceedings of the fourth European Conference on Superplastic Forming, EURO-SPF05, Birmingham, England, June 2005 2005
[ACT111]E. Mathey, L. Penazzi, F. Ronde-oustau and F. Schmidt. Automatic optimization of the cooling of injection mould based on the boundary element method. Proceedings of 8th International Conference on Numerical Methods in Industrial Forming Processes 2004
[ACT112]L. Penazzi, D. Attaf, L. Robert, J.C. Dupré, V. Valle and J.-J. Orteu. Etude expérimentale par photoélasticimétrie de la localisation de la pression de contact d'une tôle en glissement sur un rayon de matrice d'emboutissage. Proceedings of Colloque Photomécanique 2004, Albi, France 2004
[ACT113]Y. Qi, P. Bruckel, P. Lours and Z. Zhang. Investigation of adhesion and fracture of thermally grown oxide scales by interface indentation test. Proceedings of Proceedings of the fourteenth IFHTSE Congress, Shanghai, China, October 2004 2004
[ACT114]T. Branza, A. Martinier, A. Duchosal, F. Deschaux Beaume, G. Bernhart and P. Lours. Fatigue damage and weld repair of heat resistant cast steel SPF dies. Proceedings of Proceedings of the third European Conference on Superplastic Forming, EURO-SPF04, Ed. by G. Bernhart, T. Cutard & P. Lours, Albi, France, July 2004 2004
[ACT115]Y. Le Maoult, P. Lours, D. Adé and B. Pieraggi. Etude dynamique de l'écaillage des oxides de l’alliage PM2000: apport d'une nouvelle technique de trajectographie vidéo. Proceedings of Actes du Colloque Photomécanique - Albi, France, Mai 2004 2004
[ACT116]C. Gao, G. Bernhart and P. Lours. Damages induced by thermomechanical cycles in superplastic forming tools . Proceedings of Proceedings of the 7th Asia-Pacific Symposium on Engineering Plasticity and Its Application AEPA’04 Shanghai, China, september 2004 2004
[ACT117]P. Bruckel, P. Lamesle, P. Lours and B. Pieraggi. Isothermal oxidation behaviour of a hot-work tool steel . Proceedings of Proceedings of the 6th International Conference on High Temperature Corrosion and Protection of Materials - Les Embiez, France, May 2004 2004
[ACT118]C. Mabru, C. Espinosa and R. Chieragatti. Étude thermomécanique d’une nouvelle géométrie d’éprouvette de fatigue en environnement sévère. Proceedings of 16 ème Congrès Français de Mécanique 2003 [OATAO]
[ACT119]F. Rézaï-aria, F. Medjedoub, S. Le Roux, G. Dour, P. Hairy, H. Khang-Ny and M. Golin. An investigation on thermal fatigue surface cracking of 5CrMoV die tool steel. Proceedings of 22nd International Die Casting Congress & Exposition p.363-368 2003
[ACT120]E. Mathey, L. Penazzi, F. Schmidt and F. Ronde-oustau. Numerical Simulations of Polymer Cooling in Laminated Injection Moulds. Proceedings of 6th ESAFORM 2003
[ACT121]P. Bruckel, P. Lamesle, P. Lours and B. Pieraggi. XRD investigations on the oxides grown on hot work tool steels in H2O-containing atmospheres. Proceedings of Proceedings of the Electrochemical Society Symposium on High Temperature Corrosion and Materials Chemistry IV, pp 135-146 Paris, France, April-May 2003 2003
[ACT122]G. Bernhart, F. Nazaret, A. Martinier, C. Gao, D. Garriga Majo, T. Cutard and P. Lours. Design of SPF dies based on advanced material behaviour models. Proceedings of International Conference on Superplasticity of Advanced Materials ICSAM 2003, Oxford, UK, July 2003 2003
[ACT123]T. Branza, A. Duchosal, G. Fras, F. Deschaux Beaume and P. Lours. Experimental and numerical investigations of the weld repair of superplastic forming dies. Proceedings of Proceedings of the International Conference AMPT Advanced Materials Processing Technology Industrial Tools Dublin, Ireland, July 2003 2003
[ACT124]H.V. Bui, P. Lours, G. Bernhart, B. Le Razer and P. Barcq. L'outillage rapide: nouvelle technologie de fabrication rapide de pièces et d’outillage par frittage de poudre - Analyse technique et scientifique. Proceedings of Actes du colloque PMF 2003, Commission poudres et matériaux frittés de la SF2M-GFC « De la poudre au matériau massif» Albi, Ecole des Mines, Juin 2003 2003
[ACT125]H.V. Bui, P. Lours and G. Bernhart. Influence of porosity and anisotropy on the mechanical properties of direct laser sintered metal powder for injection moulding tools. Proceedings of Proceedings of the 4th International Conference on Industrial Tools Bled, Slovenia, April 2003 2003
[ACT126]D. Garcia, J.-J. Orteu and L. Penazzi. A Combined Temporal Tracking and Stereo-correlation Technique for Accurate Measurement of 3D Displacements: Application to Sheet Metal Forming. Proceedings of 9th International Metal Forming Conference, Birmingham (UK), 9-11 September 2002 2002
[ACT127]F. Monies, Y. Landon, W. Rubio and J.-M. Redonnet. Detection and correction of local and global collisions for the end milling of sculptured surfaces. Proceedings of 4th International Conference on Integrated Design and Manufacturing in Mechanical Engineering (IDMME 2002), Clermont-Ferrand, France, May 14–16, 2002 2002
[ACT128]Y. Landon, G. Cohen, J.-M. Redonnet and P. Lagarrigue. Elaboration of a master-piece for the characterisation of the Tool Positioning Defect in milling. Proceedings of 4th International Conference on Integrated Design and Manufacturing in Mechanical Engineering (IDMME 2002), Clermont-Ferrand, France, May 14–16, 2002 2002
[ACT129]S. Segonds, Y. Landon, G. Cohen and P. Lagarrigue. Virtual Reality : Application to the turning center. Proceedings of 18th Conference on Manufacturing Research, Leeds, United Kingdom, May 27–31, 2002 2002
[ACT130]R. Chieragatti, C. Mabru, C. Espinosa and F. Rézaï-aria. A new specimen for fatigue investigations . Proceedings of High Temperature Fatigue CAMP2002 ; Paderborn (D), p.207-213 2002
[ACT131]B. Miquel, S. Jean, S. Le Roux, P. Lamesle and F. Rézaï-aria. Heat-checking of hot work tool steels. Proceedings of 9th SF2M Spring Meeting on Temperature Fatigue Interaction p.185-193 2002
[ACT132]V. Velay, A. Persson, G. Bernhart, L. Penazzi and J. Bergström. Thermal fatigue of a tool steel: experiment and numerical simulation. Proceedings of 6th International Tooling Conference: The Use Of Tool Steels: Experience And Research p.667-685 2002
[ACT133]G. Bernhart, S. Baleix, P. Lours and T. Cutard. Thermomechanical behaviour and characterisation of SPF tooling materials. Proceedings of Second European Conference on Superplastic Forming, EURO-SPF02 Bristol, UK, June 2002 2002
[ACT134]G. Bernhart, S. Baleix and P. Lours. Fissuration et écaillage de couches d’oxyde lors de cycles thermiques . Proceedings of Journée thématique du groupe de travail «Interfaces dans les milieux solides»-Colloque Mécamat ONERA Châtillon, France, Janvier 2002 2002
[ACT135]Y. Landon, P. Lagarrigue, F. Monies and W. Rubio. Correction of circularity defects of a N.C. Machine Tool. Proceedings of 2nd International Conference of the European Society for Precision Engineering and Nanotechnology (EUSPEN), Turin, Italy, May 27–31, 2001 2001
[ACT136]A. Oudin, P. Lamesle, L. Penazzi, S. Le Roux and F. Rézaï-aria. Thermomechanical fatigue behaviour and life assessment of hot work tool steels. Proceedings of 9th SF2M Spring Meeting on Temperature Fatigue Interaction p.195-201 2001
[ACT137]S. Claudinon, P. Lamesle, J.-J. Orteu and R. Fortunier. Contribution à l'étude de la distorsion au traitement thermique : suivi continu par vision artificielle et simulation numérique par éléments finis. Proceedings of Colloque Photomécanique 2001, Futuroscope, Poitiers (France), 24-26 avril 2001 2001
[ACT138]S. Claudinon, P. Lamesle, J.-J. Orteu and R. Fortunier. Monitoring distortions of metallic parts during heat treatment. Proceedings of 5th ASM Heat Treatment and Surface Engineering Conference in Europe, Gothenburg (Sweden), 7-9 June 2000 2000
[ACT139]N. Roustit, D. Garcia, J.-J. Orteu and F. Rézaï-aria. Monitoring of in-plane cracking using correlation-based image processing: preliminary results . Proceedings of International Workshop on Video-Controlled Materials Testing and In-Situ Microstructural Characterization, Nancy (France), 16-18 November 1999 1999
[ACT140]S. Baleix, S. Le Roux, G. Bernhart and P. Lours. Surface and image analysis of oxides grown and spalled on heat resistant cast steels exposed to thermal cycles. Proceedings of International Conference on Advances in Materials and Processing Technologies AMPT 99 p.1175-1184 1999
[ACT141]G. Bernhart, P. Lours, F. Rézaï-aria and C. Levaillant. Effet de la thermique transitoire sur l’endommagement des outillages dans les procédés de formage . Proceedings of Actes des journées de la Société Française des Thermiciens (SFT) sur la thermique de la machine outil et de l’usinage, Bordeaux (France), 20 janvier, 1999 1999
[ACT142]Y. Le Maoult, S. Baleix, P. Lours and G. Bernhart. Application industrielle de la thermographie infrarouge au comportement des outillages de formage superplastique . Proceedings of Actes des journées du GAMI du CETIM sur les applications de la thermographie dans les industries mécaniques, Senlis (France), 22-23 juin, 1999 1999
[ACT143]S. Baleix, P. Lours and G. Bernhart. High temperature mechanical behaviour of NiCrFe heat resistant cast steel . Proceedings of Proceedings of the 8th International Conference on Mechanical Behaviour, Victoria (Canada), 1999 1999
[ACT144]S. Baleix, Y. Le Maoult, S. Frenois, Y. Marcel, P. Lours and G. Bernhart. Simulation of service life cycle induced thermomechanical stresses in a superplastic forming tool . Proceedings of Proceedings of the 3rd international Congress on Thermal Stresses, edited by J.J. Skrzypek and R.B. Hetnarski, Cracow (Poland), 317, 1999 p.317 1999
[ACT145]S. Claudinon, R. Fortunier, P. Lamesle and J.-J. Orteu. Suivi continu par vision de la distorsion d'outils au traitement thermique. Proceedings of 37èmes Journées du Cercle d'Étude des Métaux - "les aciers pour moules et outils", Albi (France), 27-28 mai 1998 1998
[ACT146]S. Claudinon, J.-J. Orteu, P. Lamesle and R. Fortunier. Mesure par voie optique des distorsions au traitement thermique de matériaux métalliques. Proceedings of Colloque Photomécanique 98, Marne la Vallée (France), 14-16 avril 1998 1998
[ACT147]M. Vivas, P. Lours, C. Levaillant, A. Couret, M.-J. Casanove and A. Coujou. On the strengthening of aluminium alloy 6056-T6 . Proceedings of Proceedings of the 6th International Conference on Aluminum alloys, edited by T. Sata, S. Kumai, T Kobayashi and Y. Murakami, Toyohashi (Japan), 2, 943, 1998 p.943 1998
[ACT148]S. Claudinon, P. Lamesle, J.-J. Orteu and R. Fortunier. Utilisation des éléments finis pour la prévision des déformations en traitement thermique. Proceedings of Journées franco-allemandes ATTT-AWT sur les déformations en traitement thermique, Belfort (France), 24-25 avril 1997 1997
[ACT149]P. Lamesle, M. Vilasi, J.-M. Claude and P. Steinmetz. Effect of palladium and chromium additions on the oxidation behaviour of beta-NiAl alloys. Proceedings of 4th International Symposium on High Temperature Corrosion and Protection of Materials p.171-178 1997
[ACT150]P. Lamesle, P. Steinmetz, M. Vilasi and J.-M. Claude. Influence of palladium on diffusion processes in the B2 NiAl phase. Proceedings of 4th International Symposium on High Temperature Corrosion and Protection of Materials p.163-170 1997
[ACT151]L. Penazzi, G. Yang, C. Levaillant and A. Le Floch. Assessment Of Thermal Effect In Sheet Metal Forming Processes. Proceedings of International Deep Drawing Group, IDDRG 18th Biennal Congress, Miskolc, Hungary, 1996
[ACT152]U. Dahmen, N. Thangararaj and P. Lours. Applications of hrem to the structural analysis of crystalline interfaces . Proceedings of Proceedings Of The 50th Annual Meeting Of The Electron Microscopy Society Of America, Edited By G.w Bailey, J.bentley And J.a.small, San Francisco Press Inc., 114, 1992 1992
[ACT153]P. Lours, K. Westmacott and U. Dahmen. Shape transformation of germanium precipitates in aluminum . Proceedings of In « Structure & Properties Of Interfaces In Materials » Edited By W. A. T. Clark, U. Dahmen & C. L. Briant - Materials Research Society Symposium Proceedings Pittsburgh Pa, 238, 207, 1992 1992
[ACT154]N. Clément, P. Lours, A. Coujou and D. Caillard. Stress anomalies in the gamma prime strengthening phase of cmsx2 superalloy - macroscopic & microscopic deformation tests . Proceedings of Proceedings Of The 9th International Conference On The Strength Of Metals And Alloys, Haïfa Israël, 1991 1991
[ACT155]N. Clément, D. Caillard, A. Couret, G. Molena , A. Coujou, A. Bénéteau, P. Lours and B. De Mauduit. Déformation in situ à différentes températures de monocristaux de phase gamma prime de cmsx2 . Proceedings of Actes Du Colloque National Superalliages Monocristallins, Nancy, 151, 1990 p.151 1990
[ACT156]P. Lours, A. Coujou, B. De Mauduit and N. Clément. High temperature stress induced spreading of superlattice intrinsic stacking fault in the gamma prime phase of the cmsx2 superalloy . Proceedings of Advanced Materials And Processes - Proceedings Of The First European Conference Euromat 89, Aachen FRG, Vol. 1, P 481-486, 1990 p.481-486 1990
[ACT157]A. Coujou, A. Bénéteau, G. Alcouffe and P. Lours. A geometrical method to characterize the order in microtwins from in situ observations . Proceedings of Proceedings Of The 8th International Conference On The Strength Of Metals And Alloys, Edited By P.o.kettunen, T.k.lepistö, M.e.lehtonen, Pergamon Press Oxford, 1, 133, 1988 - Tampere Finland p.133 1988

Communication sans actes dans un congrès international ou national

[COM1]H.L. Dorothy , P. Longère and A. Dragon. Coupled ASB- and microvoiding-assisted dynamic ductile failure. 23rd DYMAT Technical Meeting, Dynamic fracture of ductile materials, Trondheim (Norway), 12-14 September 2017 2017
[COM2]H.L. Dorothy and P. Longère. Modelling of Adiabatic Shear Band and Microvoid induced Material Degradation . COMPLAS 2017, XIV International Conference on Computational Plasticity. Fundamentals and Applications, Barcelona (Spain), 5-7 September 2017 2017
[COM3]H.L. Dorothy and P. Longère. Numerical modelling of structural degradation under adiabatic shear banding and micro-voiding. CFRAC2017, 5th International Conference on Computational Modeling of Fracture and Failure of Materials and Structures, Nantes (France), 14-16 june 2017 2017
[COM4]H.L. Dorothy , P. Longère, A. Hor and A. Dragon. Modeling of high strain rate failure unser ASB and microvoiding. IMPLAST 2016, 11th International Symposium on Plasticity and Impact Mechanics, New Delhi (India), 11-14 December 2016 2016
[COM5]A. Hor, I. Thabet, B. Malard, N. Ratel-ramond, J. Huez, V. Baylac and C. Estournès. Évaluation des contraintes résiduelles dans l’alliages Ti-6Al-4V mis en forme par SLM. Groupement Français d'Analyse des Contraintes - GFAC 2016, Toulouse, France 2016
[COM6]C.M. Sanchez Camargo, A. Hor, C. Mabru and R. Chieragatti. Détermination des paramètres des lois de comportement à partir de la courbe de nanoindentation et de la topographie de l'empreinte résiduelle. Indentation 2016, Lille, France 2016
[COM7]C.M. Sanchez Camargo, A. Hor, C. Mabru and R. Chieragatti. Dispersion sources in nanoindentation test data used to determinate the constitutive law of metallic materials.. Materials Science and Engineering (MSE 2016), Darmstadt, Germany 2016
[COM8]M. Rollin, L. Penazzi, V. Velay, A. Dupuy and S. Gallet. Superplastic forming optimization technique based on average strain rate controlling – Numerical simulation and experimental validation. EuroSPF 2016 2016
[COM9]G. Manar, P. Longère, E. Roux, A. Hor and M. Salem. Effect of strain rate on the behavior and failure of 2024 and 7075 aluminum alloys. DSTC 2016, 3rd International Conference on Defence and Security Technology, Kuala Lumpur (Malaysia), 15-17 August 2016 2016
[COM10]H.L. Dorothy , P. Longère, A. Hor and A. Dragon. Description of ASB-dynamic localisation as a degradation mechanism. MTDM2016 - The 10th International Conference on the Mechanics of Time Dependent Materials, Paris (France), 17-20 May 2016 2016
[COM11]P. Longère and H.L. Dorothy . Strain localisation described as a damage-like mechanism: (1-D) vs. D type modeling. MécaDymat - Comportement et rupture des matériaux sous sollicitations dynamiques, Strasbourg (France), 30-31 Mars 2016 2016
[COM12]A. Zouaghi, A. Soveja, F. Rézaï-aria, T. Pottier, M. Cheikh and V. Velay. Multi-scale surface modeling of the nonlinear mechanical behaviour of AISI H11 hot work tool steel. International Conference on Plasticity, Damage, and Fracture 2016
[COM13]G. Bernhart, V. Velay and T. Cutard. Moules pour formage superplastique du titane : matériaux, propriétés et conception. Moules et Outils 2015 2015
[COM14]S. Cafieri, F. Monies, M. Mongeau and C. Bes. Optimizing plunge milling aeronautical parts via MINLP. orsc - euro - 2015, Shanghai, May 10-12 2015
[COM15]R. Julien, V. Velay, V. Vidal, M. Salem, Y. Dahan, R. Forestier and F. Rézaï-aria. Thermomechanical behaviour and microstructural evolution of high temperature forged Ti-6Al-4V during heat treatment quenching. 12th International Conference on the Mechanical Behavior of Materials, Karlsruhe - GERMANY 2015
[COM16]E. Copin, T. Sentenac, Y. Le Maoult, F. Blas, F. Ansart and P. Lours. Feasibility of multilayer sol-­gel thermal barrier coating manufacturing for through thickness temperature gradient sensing. 41st International Conference on Metallurgical Coatings and Thin Films 2014 (ICMCTF), 27 Avril – 2 Mai 2014, San Diego (USA) 2014
[COM17]E. Vermesse, C. Mabru and L. Arurault. Influence of surface integrity induced by anodizing process on fatigue life of Ti-6Al-4V. JIP 2013 13th International Spring Meeting FATIGUE BEHAVIOUR: FROM SPECIMEN TO STRUCTURE Paris, France, May 22-23, 2013 2013
[COM18]E. Copin, M. Assali, M. Portela, Y.-F. Huang, J. Rao and D. Bhattacharyya. RF sputtered multilayer yttria stabilised zirconia near-infrared mirrors. 26th International Conference on Surface Modification Technologies (SMT26), 20-­‐22 juin 2012, Ecully (France) 2012
[COM19]J. Limido, M. Suraratchai, C. Mabru, C. Espinosa, M. Salaün, R. Chieragatti and M. Chaussumier. Surfaces usinées: cas d'aillages d'aluminium aéronautiques. Séminaire du GT 7 de la SF2M, 29 mars 2012, Paris (FR) 2012
[COM20]C. Bellot, F. Taina, E. Cabrol, C. Carniel, P. Lamesle and P. Lours. Nouvelle technique de caractérisation physico-chimique des alliages à durcissement structural. Journées d'Automne de la SF2M 2012
[COM21]K. Ben Slima, C. Mabru, L. Penazzi and F. Ronde-oustau. Effet des défauts de fonderie sur la tenue en fatigue des pièces en fonte à graphite sphéroïdal : application au dimensionnement des outils d’emboutissage de tôles de véhicules automobiles . Colloque Moules et Outils 2011, Ecole des Mines d'Albi, 20-21 octobre 2011 2011
[COM22]L. Penazzi, S. Ramde, F. Ronde-oustau, H. Sfar and C. Piat. Effet de déformation de lames de cisaillage : comparaison des résultats d'essais et de simulation numérique. Colloque Moules Et Outils 2011 - Ecole Des Mines d'Albi, 20-21 Octobre 2011 2011
[COM23]C. Boher, L. Penazzi, S. Le Roux, V. Lucin, S. Tovar, C. Dessain and B. Tavernier. Etude de la dégradation à hautes températures de matériaux d’outils d’emboutissage vis-à vis d’une tôle USIBOR 1500P revêtue AluSi : quantification expérimentale de l’adhésion. Congrès Moules et Outils 2011
[COM24]Y. Balcaen, L. Robert, V. Velay, V. Vidal and P. Lours. Accurate strain analysis of Titanium sheet in single point incremental forming process by digital image correlation. Photomechanics 2011, Brussels, Belgium, february 2011
[COM25]T. Kagnaya, L. Lambert, C. Boher, T. Cutard, M. Lazard and L. Velnom. Endommagement du WC-Co en usinage. Matériaux 2010 , Nantes, FRANCE , 18-22 octobre 2010 2010
[COM26]T. Kagnaya, C. Boher, L. Lambert, M. Lazard and T. Cutard. Mécanismes d’endommagement du WC-6%Co en usinage.. JIFT 2010 – Journées Internationales Francophones de Tribologie, Albi, Mai, 2010. 2010
[COM27]L. Pin, F. Ansart, J. Fenech, P. Lours, J.-P. Bonino, J. Sniezewski and Y. Le Maoult. Advances in the field of new smart thermal barrier coatings . CIMTECH Venezzia Italy 2010 2010
[COM28]J. Sniezewski, V. Vidal, Y. Le Maoult and P. Lours. In situ and ex situ investigation of thermal barrier coating adherence and spallation. EUROCORR 2009 – The European Corrosion Congress - EFC Event n°310 - Nice, France, September 2009 2009
[COM29]F. Bugarin, N. Decultot, M. Devy, J. Harvent, J.-J. Orteu, L. Robert and V. Velay. Multi-camera computer vision for large volume inspection: (a) aeronautical parts inspection and (b) incremental forming. Large Volume Metrology Conference 2008 (LVMC'2008), Liverpool (UK), 4-5 November 2008 2008
[COM30]L. Robert, N. Decultot, V. Velay, S. Ramde and G. Bernhart. Behaviour identification of aluminium sheet used in Single Point Incremental Forming by Finite Element Method Updated. Photomechanics 2008, Loughborough, UK 2008
[COM31]J. Limido, M. Suraratchai, C. Mabru, C. Espinosa, M. Salaün and R. Chieragatti. Effet des paramètres d'usinage sur la durée de vie en fatigue d'un alliage d'aliminium. Les journées techniques du CETIM: Fatigue et procédés de fabrication, 26 juin 2008, Senlis (FR) 2008
[COM32]J. Limido, C. Espinosa, J.-L. Lacome, R. Chieragatti, M. Salaün and C. Mabru. Utilisation de la méthode SPH pour simuler l’interaction outil matière en coupe orthogonale. Journées "Simulation et rhéologie de la coupe", Réseau "Procédés" de l'ENSAM, 20-21 mars 2008, Talence (FR) 2008
[COM33]S. Chevalier, J.-N. Felices and W. Rubio. Génération de surfaces enveloppes pour l'usinage de pièces en Bois avec des outils de forme. XIV Colloque National de la Recherche en IUT à Villeurbanne, 2008
[COM34]F. Pettinari-Strumel, M. Benyoucef, J. Douin, P. Lours and A. Coujou. The role of the gamma - gamma prime interface in the creep behavior of the NR3 superalloy. 2nd International Symposium on Aircraft Materials ACMA08, Agadir, Marocco, May 2008 2008
[COM35]T. Branza, V. Velay, F. Deschaux Beaume and P. Lours. Weld-repair of heat resistant cast steels for SPF dies – prevention of cracking and fatigue behavior. EURO-SPF 2008, Carcasonne, France, 2008 2008
[COM36]J. Sniezewski, Y. Le Maoult, F. Crabos and P. Lours. Cyclic oxidation of thermal barrier coatings – In situ analysis under controlled temperature gradient. 19th AEROMAT - Annual Advanced Aerospace Materials and Processes Conference & Exhibition - Austin, Texas, USA, June 2008 2008
[COM37]J. Sniezewski, Y. Le Maoult and P. Lours. Oxidation and spallation of FeCrAl alloys and thermal barrier coatings – In situ investigation under controlled temperature gradient. 2nd International Symposium on Aircraft Materials ACMA08, Agadir, Marocco, May 2008 2008
[COM38]P. Lamesle, S. Le Roux and F. Rézaï-aria. Suivi in-situ par vision artificielle des déformations d’une pièce métallique pendant une trempe. Congrès national A3TS - Journées "Moules & Outils" 2007
[COM39]F. Rézaï-aria, C. Boher, G. Dour, P. Lamesle and S. Le Roux. Endommagement et durée de vie des outillages de mise en forme à chaud. Congrès national A3TS - Journées "Moules & Outils 2007
[COM40]S. Hmida-mamaar, F. Schmidt, L. Robert, V. Velay and L. Chevalier. Identification du Comportement de Membranes en Polymères par Analyse Inverse au cours du Procédé de Soufflage. 2ème congrès Rotomoulage, Thermoformage et Soufflage 2007
[COM41]M. Tata, D. Miroud, S. Lebaili, N. Fouchal, T. Cutard and C. Boher. Etude de la caractérisation des frittés WC-W-Ni infiltrés par Cu-Mn. Colloque "Science et Technologie des Poudres & Poudres et Matériaux Frittés" Ecole des Mines d'Albi, du 23 au 25 mai 2007 2007
[COM42]E. Herny, P. Lours, E. Andrieu, J.-M. Cloué and P. Lagain. Evolution of microstructure and impact-strength energy in thermally and thermomechanically aged 15-5 PH. 1st International Symposium on Aircraft Materials ACMA07, Agadir, Marocco, Mai 2007 2007
[COM43]S. Hmida-maamar, F. Schmidt, L. Robert and V. Velay. Parameters Identification using Field Measurements of Polymer Membranes during Bubble Inflation Technique. Photomechanics 2006, Clermont-Ferrand (France), 10-12 July 2006
[COM44]S. Hmida, F. Schmidt, L. Robert, V. Velay and D. Mercier. Modélisation du comportement de membranes en polymères durant le procédé de soufflage. 1er congrès Rotomoulage, Thermoformage et Soufflage 2005
[COM45]T. Cutard, P. Lours and G. Bernhart. Mechanical Properties of SPF-tooling Materials. Second European Conference on the Superplastic Forming Process (EuroSPF02) – Bristol (Angleterre) – Juin 2002. 2002
[COM46]S. Claudinon, P. Lamesle, J.-J. Orteu and R. Fortunier. Amélioration de la connaissance et de la prévision des distorsions d'aciers au traitement thermique. Journées d'Automne 2000 de la Société Française de Métallurgie et de Matériaux, Paris (France), 17-19 octobre 2000 2000
[COM47]T. Cutard, P. Lours and G. Bernhart. New developments on metallic and ceramic toolings for the superplastic forming of titanium alloys. Journées du Groupe Anglais de Superplasticité - Farnborough (UK) – Juin 2000. 2000

Communication par poster dans un congrès international ou national

[AFF1]J. Huez, B. Malard, F. Bruno, K. Ugras, A. Hor, N. Ratel-ramond, G. Chevalier, C. Estournès and G. Geandier. Evaluation des contraintes résiduelles dans les alliages de TA6V « Near Net Shape » mis en forme « Spark Plasma Sintering ». 2016
[AFF2]S. Amiel, E. Copin, T. Sentenac, Y. Le Maoult and P. Lours. Caractérisation de marqueurs de l’histoire thermique photoluminescents. Congrès Français de Thermique 2016, 31 Mai – 3 Juin 2016, Toulouse 2016
[AFF3]E. Copin, T. Sentenac, Y. Le Maoult and P. Lours. Fonctionnalisation de barrières thermiques sol-gel YSZ pour la mesure de température et le CND par fluorescence. 6e colloque de l’Institut Mines-Télécom « Matériaux : réalités et nouvelles frontières», 30-31 Mars 2016, Paris 2016
[AFF4]A. Zouaghi, V. Velay, A. Soveja, R. Chieragatti and F. Rézaï-aria. Une étude multi-échelle du comportement en surface de l´acier X38CrMoV5 : approche numérique et expérimentale. 21ème CONGRÉS FRANÇAIS DE MÉCANIQUE [CFM2013] 2013
[AFF5]S. Ramde, L. Penazzi, F. Ronde-oustau, A. Jefat, C. Thuilliez and P.Y. Manach. De l'opération d'emboutissage à celle de poinçonnage en suivant le comportement de la tôle. Journée Aum / Afm 2010, Lorient, 25-27 Août 2010. 2010
[AFF6]G. Kaza, C. Boher, G. Dour, T. Loulou, P. Carré and L. Penazzi. Influence des paramètres de rugosité pour la modélisation de la résistance thermique de contact à l'interface tôle-outil en emboutissage à chaud. Journées. Internationales Francophones De Tribologie, Albi, 27-28 Mai 2010 2010
[AFF7]L. Penazzi, S. Le Roux, V. Lucin, J.-M. Mouys, S. Tovar, J.-P. Arcens and C. Boher. Etude des dégradations des outils d'emboutissage et estimation des volumes d'usure. Colloque Des J. Internationales Francophones De Tribologie, Albi, 27-28 Mai 2010 2010
[AFF8]Y. Balcaen, N. Decultot, V. Vidal, V. Velay, L. Robert and P. Lours. Etude des mécanismes de déformation en formage incrméntal. Colloque Plasticité 2010, Toulouse, France 2010
[AFF9]S. Le Roux, F. Medjedoub, G. Dour and F. Rézaï-aria. Application of image analysis for thermal fatigue heat checking investigations. 8th International Tooling Conference 2009
[AFF10]A. Sellidj, S. Lebaili and P. Lours. Morphology of the interface of a deposit alloy type stellite on steel and his evolution in thermal fatigue. International Conference- Fatigue and Plasticity : from mechanisms to design Paris, France, May 2008 2008
[AFF11]M. Salem, P. Lamesle, H. Laribou, S. Le Roux, G. Dour and F. Rézaï-aria. Effet de l’environnement par fatigue thermique des aciers à outils pour travail à chaud X38CrMoV5 (AISI H11). Congrès national A3TS - Journées "Moules & Outils 2007
[AFF12]J. Limido, M. Suraratchai, C. Mabru, C. Espinosa, M. Salaün and R. Chieragatti. Effet des paramètres d'usinage sur la drée de vie en fatigue des pièces aéronautiques en alliages d'aluminium de la série 7000. MECAMAT 2007 Fatigue des matériaux et des srtuctures, 22-26 janvier, Aussois (FR) 2007 [OATAO]
[AFF13]A. Sellidj, S. Lebaili and P. Lours. Vieillissement d’un dépôt d’alliage de type Stellite F durant des recuits à haute température. 26ième journée de printemps de la SF2M, Paris, France, Mai 2007 2007
[AFF14]E. Herny, P. Lours, P. Lagain, J.-M. Cloué, M.-C. Lafont and E. Andrieu. Evolution de la microstructure et des propriétés mécaniques de l’acier inoxydable martensitique 15-5PH après vieillissement . Actes du congrès Matériaux 2006, Dijon France, 13-17 Novembre 2006 2006
[AFF15]E. Herny, P. Lours, P. Lagain, J.-M. Cloué, S. Pérusin and E. Andrieu. Local mechanical and microstructural characterization of EB welded 15-5 PH stainless steel. Proceedings of EUROMAT conference, Praha, Czech Republic, September 2005 2005
[AFF16]T. Branza, G. Bernhart, P. Lours, F. Deschaux Beaume, V. Richefeu, A. Duchosal and G. Fras. Rechargement TIG d’outillages de formage superplastique: essais et simulation . Actes du Colloque National MECAMAT, Ecole de Mécanique des Matériaux : « Assemblages : des Matériaux à la Structure » Ed. V. Aubin, S. Degallaix, Y. Desplanques, MC. Tan 2003
[AFF17]P. Lours, K. Bavard, H.V. Bui and G. Bernhart. Influence of casting defects on the fatigue behaviour of martensitic tool steel . 4th International Conference on Mechanics and Materials in Design Nagoya, Japon, June 2002 2002
[AFF18]S. Baleix, G. Bernhart, E. Cailleux, T. Cutard and P. Lours. Matériaux réfractaires pour outillages de formage superplastique . Actes du Colloque Matériaux Réfractaires de la SF2M Section sud-est, Cavaillon (France), 13-14 janvier, 1999 1999
[AFF19]E. Cailleux, P. Lours, T. Cutard and G. Bernhart. Structural and mechanical properties of a refractory concrete for superplastic forming tools. CIMTEC'98-World Ceramics Congress & Forum on New Materials–Florence (Italie) - Juin 1998. 1998
[AFF20]P. Lours, J. Alexis and G. Bernhart. High temperature oxidation behaviour and creep properties of ODS alloy PM2000 . Proceedings of the 14th International Plansee Seminar, edited by G. Kneringer, P. Rödhammer & P. Wilhartitz, Reutte (Austria), 1, 869, 1997 1997
[AFF21]P. Lours, A. Coujou and B. De Mauduit. Observation in situ dans un met de l’étalement des sisf sous contrainte à haute température- phase gamma prime du superalliage cmsx2. Colloque Plasticité 89 Saint-etienne (france), 1989 1989
[AFF22]A. Coujou, P. Lours, N. Clément and D. Caillard. Simulation par la méthode des éléments finis de la répartition des contraintes dans une microéprouvette de traction in situ - phase gamma prime du superalliage cmsx2. Colloque Plasticité 89 Saint-Etienne (france), 1989 1989
[AFF23]P. Lours, B. De Mauduit, A. Bénéteau, N. Clément and A. Coujou. Formation of prismatic loops induced by in situ straining of the γ’ phase of a ni-base superalloy . Proceedings Of The 8th International Conference On The Strength Of Metals And Alloys, Edited By P.o.kettunen, T.k.lepistö, M.e.lehtonen, Pergamon Press Oxford, 1, 251, 1988 - Tampere Finland 1988
[AFF24]N. Clément, D. Caillard, P. Lours and A. Coujou. In situ deformation of a gamma prime nickel base single crystal. the movement of screw dislocations in (001) planes from -100°c to 880°c . Proceedings Of The 8th International Conference On The Strength Of Metals And Alloys, Edited By P.o.kettunen, T.k.lepistö, M.e.lehtonen, Pergamon Press Oxford, 1, 205, 1988- Tampere Finland 1988
[AFF25]A. Bénéteau, P. Lours, B. De Mauduit, N. Clément and A. Coujou. Observation in situ de la déformation plastique par traction suivant [100] de monocristaux de phase gamma prime . Colloque Plasticité 87 Lusanne Suisse 1987

Chapitre d'ouvrage scientifique

[OSC1]J. Senatore, F. Monies and W. Rubio. 5-axis Flank milling of sculptured surfaces. In book Machining of complex sculptured surfaces, Chap. 2, p.33-67. Ed. Springer. 2012 ISBN:978-1-4471-2355-2
[OSC2]D. Delagnes. Annexe 19 : Outillage. In book La Métallurgie - Science et ingénierie, p.. Ed. EDP SCIENCES. 2011 ISBN:978-2-7598-0538-9
[OSC3]G. Bernhart, P. Lours, T. Cutard, V. Velay and F. Nazaret. Processes and equipments for superplastic forming of metals . In book Superelastic Forming of Advanced Metallic Materials – Methods & Applications, Chap. 3, p.49-71. Ed. Woodhead Publishing in Materials. 2011 ISBN:978-1-84569-753-2 [DOI]
[OSC4]L. Berquez, M. Mousseigne, V. Haas and J.-L. Franceschi. Contrôle non destructif thermoacoustique. In book Instrumentation, interdisciplinarité et innovation : colloque interdisciplinaire en instrumentation C2I'98, p.. Ed. Lavoisier-Hermes. 1998 ISBN:9782866017309

Direction d'ouvrage collectif

[DO1]C. Boher and J.-F. Rouchon. Modélisation du contact et de l'usure. Sciences de la matière - Presses des Mines. , 513p. Ed. Presses des Mines. 2013 ISBN:978-235671-033-8
[DO2]G. Bernhart, T. Cutard and P. Lours. Third European Conference on SuperPlastic Forming - Proceedings. CEPADUES-EDITIONS. , Ed. CEPADUES-EDITIONS. 2004 ISBN:2.85428.649.9

Thèse de Doctorat ou HdR

[TH1]C. Boher. Réponses aux sollicitations tribologiques d'oxydes métalliques et d'alliages ductiles : Organisation de la déformation plastique dans les Transformées Tribologiques de Surface, conséquences sur le débit source de troisième corps. Habilitation à diriger des recherches, . 2016 [HAL]
[TH2]T. Sultan. Usinage des métaux durs par jet d'eau abrasif. Thèse de doctorat, Université de Toulouse. 2015
[TH3]E. Copin. Fonctionnalisation de barrières thermiques aéronautiques YSZ issues de la voie sol-­gel : mesure de température et diagnostic de l’endommagement par fluorescence. Thèse de doctorat, École Nationale Supérieure des Mines d'Albi-Carmaux. 2015 [HAL]
[TH4]K. Moussaoui. Influence de l’usinage sur la durée de vie en fatigue de pièces aéronautiques en alliage de titane. Thèse de doctorat, Université Paul Sabatier. 2013
[TH5]C. Mabru. Etats de surface - Matériaux de surface : résistance à l'endommagement. Habilitation à diriger des recherches, Institut National Polytechnique de Toulouse. 2012 [OATAO]
[TH6]D. Delagnes. La microstructure des aciers martensitiques revenus : une approche multi-échelles nécessaire à la maîtrise des propriétés mécaniques. Habilitation à diriger des recherches, Institut National Polytechnique de Toulouse. 2011
[TH7]Y. Landon. Analyse et optimisation des processus de fabrication par une approche globale. Habilitation à diriger des recherches, Université Toulouse 3 - Paul Sabatier. 2010
[TH8]L. Penazzi. Dimensionnement thermomécanique des outillages de mise en forme des matériaux. Habilitation à diriger des recherches, Université De Toulouse. 2010
[TH9]G. Cohen. Etude des effets thermiques et mécaniques en usinage à sec. Application à la qualité de la pièce en tournage. Thèse de doctorat, Université Paul Sabatier. 2009
[TH10]P. Gilles. Positionnement d'outil torique pour l'usinage de surfaces gauches en fraisage 5-axes avec équilibrage de l'effort de coupe transversal. Thèse de doctorat, l'Université Toulouse III - Paul Sabatier. 2008
[TH11]J. Senatore. Analyse qualitative des paramètres influents pour la planification des trajectoires sur surfaces gauches. Thèse de doctorat, Université Paul Sabatier. 2007
[TH12]Y. Landon. Contribution à l’amélioration de la qualité d’usinage en fraisage 3 axes sur Machines-Outils à Commande Numérique par la mise en place d’un Compagnon Virtuel. Thèse de doctorat, Université Toulouse 3 - Paul Sabatier. 2004
[TH13]P. Lours. Habilitation à diriger des recherches : mémoire de synthèse présenté par Philippe Lours. Habilitation à diriger des recherches, Institut National Polytechnique de Toulouse . 2003
[TH14]P. Lours. Mécanismes de déformation plastique de la phase gamma prime du superalliage CMSX2 - Etude par microscopie électronique in situ. Thèse de doctorat, Université Paul Sabatier de Toulouse. 1989

Autre publication

[AP1]R. Chieragatti, E. Paroissien and J. Huet. Faisabilité d’assemblages mixtes boulonnés-collés en aéronautique. Journées Techniques, CETIM, Saint-Etienne (F-42) 2004

Brevet

[BR1]F. Nazaret, E. Lebard, Y. Le Maoult, L. Penazzi, V. Vidal and V. Velay. Procédé de pilotage d'une machine de formage superplastique et machine correspondante. Brevet No. WO2016162642, 2016
[BR2]M. Cheikh and A. Fermy . Appareil polyvalent de recherche des propriétés mécaniques d'une éprouvette. Brevet No.2.971.845, 2012
[BR3]F. Szmytka, A. Oudin, F. Rézaï-aria and M. Salem. Banc de fatigue thermique par induction pour piston. Brevet No.FR11/51562, 2011
[BR4]R. Chieragatti, M. Suraratchai, C. Mabru, C. Espinosa and V. Vergnes. Method for characterizing the endurance limite of a part from ist surface profile. Brevet No., 2006



INSTITUT CLEMENT ADER, 3, rue Caroline Aigle F-31400 Toulouse, France.
Livraisons : +33 (0)5 61 17 10 07
Secrétariat ICA: +33 (0)5 61 17 10 85 ou +33 (0)5 61 17 10 82
Fax : +33 (0)5 61 17 10 80